2.53@3287 , Diablo II

[Diablo II]

Hmmm.... This 2.53 isn't so bad ;)

30 Lt H20 at 20°C...

With these low temps at 3287@1.8V (h20 not chilled!!!)

http://digilander.libero.it/DiabloIIx/Temps%20@%203287%20Mhz%201.800V.JPG

I've done this 3x mem bench ;) System not stable for other benches with 20°C H20 ;)

http://digilander.libero.it/DiabloIIx/Memory%20173x19%20=%203287%20Mhz%201.800V%20RDRAM% 20@%203x%20Yes%20Ext.JPG

[Diablo II]

next step is pintrick and 1.85V to reach 3300+ with 20C h20, then... chilled water at -5C for the 3dmark at 3300 or more... :D

[Jupiler]

That's a real nice oc, congrats.
Is it stable at that speed?
3300 Mhz should be possible, good luck with it.

[Diablo II]

Originally posted by Jupiler
That's a real nice oc, congrats.
Is it stable at that speed?
3300 Mhz should be possible, good luck with it.

it is not so unstable but not stable... Note that h20 is at 20°C not chilled ;)

I think that with -5C chilled h20 i'll do 3dmark flawlessly at 3300 ;)

I did pintrick successfully 15 minutes ago but setting 1.85V i had the same VCore values when setting 1.8V via jumper, so i didn't see any 3300+ mhz...

[Tom Holck]

But the problem is, that you can't use the 3/4 settings for the mem fx: 183 x 3/4 = 244 a little to high

P2.66 or 2.8 are better


Best OC

Tom Holck
Denmark

The land of Prometeia

[Diablo II]

Note i have RIMMs not DDR ;)

[ns_ripper]

real nice result diablo II !!

[Diablo II]

Originally posted by ns_ripper
real nice result diablo II !!

Thx m8! :toast:

I just realised that this is very stable in any application:

3153 mhz 166x19 at 1.7V with 25C H20 with CPU much under 40°C on full load... My new 24/7 use then...

I'm working on 169x19=32xx for the 3dmark, I just tried but it kicked me to desktop at the last test, arrgh! I can bring it totally stable even at 1.8V... Over 3.2G i'm not stable, but not so unstable though... The wall is 3300 mhz cant reach it even with 20C h20, i have to chill i, coming industrial freezer to chill 5l h20 at -5C, all at les than 200€-->190€

[ns_ripper]

Originally posted by Diablo II
Thx m8! :toast:

I just realised that this is very stable in any application:

3153 mhz 166x19 at 1.7V with 25C H20 with CPU much under 40°C on full load... My new 24/7 use then...

I'm working on 169x19=32xx for the 3dmark, I just tried but it kicked me to desktop at the last test, arrgh! I can bring it totally stable even at 1.8V... Over 3.2G i'm not stable, but not so unstable though... The wall is 3300 mhz cant reach it even with 20C h20, i have to chill i, coming industrial freezer to chill 5l h20 at -5C, all at les than 200€-->190€


Well, I got my 2.4B cpu runnig at 2827Mhz @ 155Mhz fsb.

I'm using an gigabyte 8pe667Por motherboard. normaly my cpu runs fine at 160Mhz on 1.65V- 1.7V but when I set my voltage to 1.725V in the bios I only get 1.61V :( I wish that someone knew a mod. or maybe a modded bios to get some higher voltage without screwing with the board or cpu.