Creative
09-08-2002, 02:37 AM
I know this is the wrong forum guys and i apologise. Feel free to move but keep the link so pple can see it cos more people visit this forum that the mobo vmod one...:)
Thanks to Chong for helping me out via PM before...:)
I have just done the vcore mod to the board and have used 2 wires and a 50K pot with a turning dial on it. Pretty much the same setup as the kr7a mod i did a few months ago.
I have 3 pin type things on the pot stickig up and the wire going to the ic chip Pin7 is connected to one of the outside pins and the ground wire is connected to the middle pin and the other outer one is free.
I have used a 3 plug fan thingie like in the Mricee guide and plugged it up to a fan header. The ground wire is connected to where the black one would usually be on the fan header thingie and i boot the pc. The bios is set to 1.50 and the vcore reads 1.37 with the pot turned all way to the RIGHT. I turn a little to LEFT and it increases to 1.45 (where it usualy sits at 1.50 setting) and then i keep turning and turning and it doesnt change.
This happens for every bios setting and then when I use 1.6 and above, when its turned all way to RIGHT it works cos it goes to about .7 below what its set to and then i turn the dial and it rises and then i turn some more and the pc shuts off? This happens also when i turn the dial quickly going up or down asd well
I have done evevrything right but it wont work...:( Can anyone please help me cos now i have a wire soldered to my pin7 on the ic chip and can only get a max of 1.64 volts real. I have taken the pin mod off the cpu like Opp told me to and I can go only go to 1.7 in bios. With pin done, I can get to 1.85.
Anyone??!!!
:)
[EDit: Attached Pics]
This is the axtual mod job :)
http://users.bigpond.net.au/creat/vmod/111-1178_IMG.JPG
This is the Mod again but blurry
http://users.bigpond.net.au/creat/vmod/102-0208_IMG.JPG
This is the fan connecter and i twisted the ground wire around this one and used electric tape for now to hold till my friend can solder again...:)
http://users.bigpond.net.au/creat/vmod/102-0217_IMG.JPG
The Mod in full
http://users.bigpond.net.au/creat/vmod/102-0216_IMG.JPG
Thanks to Chong for helping me out via PM before...:)
I have just done the vcore mod to the board and have used 2 wires and a 50K pot with a turning dial on it. Pretty much the same setup as the kr7a mod i did a few months ago.
I have 3 pin type things on the pot stickig up and the wire going to the ic chip Pin7 is connected to one of the outside pins and the ground wire is connected to the middle pin and the other outer one is free.
I have used a 3 plug fan thingie like in the Mricee guide and plugged it up to a fan header. The ground wire is connected to where the black one would usually be on the fan header thingie and i boot the pc. The bios is set to 1.50 and the vcore reads 1.37 with the pot turned all way to the RIGHT. I turn a little to LEFT and it increases to 1.45 (where it usualy sits at 1.50 setting) and then i keep turning and turning and it doesnt change.
This happens for every bios setting and then when I use 1.6 and above, when its turned all way to RIGHT it works cos it goes to about .7 below what its set to and then i turn the dial and it rises and then i turn some more and the pc shuts off? This happens also when i turn the dial quickly going up or down asd well
I have done evevrything right but it wont work...:( Can anyone please help me cos now i have a wire soldered to my pin7 on the ic chip and can only get a max of 1.64 volts real. I have taken the pin mod off the cpu like Opp told me to and I can go only go to 1.7 in bios. With pin done, I can get to 1.85.
Anyone??!!!
:)
[EDit: Attached Pics]
This is the axtual mod job :)
http://users.bigpond.net.au/creat/vmod/111-1178_IMG.JPG
This is the Mod again but blurry
http://users.bigpond.net.au/creat/vmod/102-0208_IMG.JPG
This is the fan connecter and i twisted the ground wire around this one and used electric tape for now to hold till my friend can solder again...:)
http://users.bigpond.net.au/creat/vmod/102-0217_IMG.JPG
The Mod in full
http://users.bigpond.net.au/creat/vmod/102-0216_IMG.JPG