LSI MegaRAID Preboot CLI and MegaCLI commands

[mobilenvidia]

Latest version of MegaCLi commands, these should also work happily in PreBoot CLi (CTRL+'Y' at LSI splash screen)
Might be of interest to some folk.

MegaCLI SAS RAID Management Tool Ver 8.02.21 Oct 21, 2011

(c)Copyright 2011, LSI Corporation, All Rights Reserved.


NOTE: The following options may be given at the end of any command below:

[-Silent] [-AppLogFile filename] [-NoLog] [-page[N]]
[-] is optional.
N - Number of lines per page.

MegaCli -v
MegaCli -help|-h|?
MegaCli -adpCount
MegaCli -AdpSetProp {CacheFlushInterval -val} | { RebuildRate -val}
| {PatrolReadRate -val} | {BgiRate -val} | {CCRate -val} | {ForceSGPIO -val}
| {ReconRate -val} | {SpinupDriveCount -val} | {SpinupDelay -val}
| {CoercionMode -val} | {ClusterEnable -val} | {PredFailPollInterval -val}
| {BatWarnDsbl -val} | {EccBucketSize -val} | {EccBucketLeakRate -val}
| {AbortCCOnError -val} | AlarmEnbl | AlarmDsbl | AlarmSilence
| {SMARTCpyBkEnbl -val} | {SSDSMARTCpyBkEnbl -val} | NCQEnbl | NCQDsbl
| {MaintainPdFailHistoryEnbl -val} | {RstrHotSpareOnInsert -val}
| {DisableOCR -val} | {BootWithPinnedCache -val} | {enblPI -val} |{PreventPIImport -val}
| AutoEnhancedImportEnbl | AutoEnhancedImportDsbl
| {EnblSpinDownUnConfigDrvs -val}|{UseDiskActivityforLocate -val} -aN|-a0,1,2|-aALL
| {ExposeEnclDevicesEnbl -val} | {SpinDownTime -val}
| {SpinUpEncDrvCnt -val} | {SpinUpEncDelay -val} | {Perfmode -val} -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -AutoDetectBackPlaneDsbl -val -aN|-a0,1,2|-aALL
val - 0=Enable Auto Detect of SGPIO and i2c SEP.
1=Disable Auto Detect of SGPIO.
2=Disable Auto Detect of i2c SEP.
3=Disable Auto Detect of SGPIO and i2c SEP.
MegaCli -AdpSetProp -CopyBackDsbl -val -aN|-a0,1,2|-aALL
val - 0=Enable Copyback.
1=Disable Copyback.
MegaCli -AdpSetProp -EnableJBOD -val -aN|-a0,1,2|-aALL
val - 0=Disable JBOD mode.
1=Enable JBOD mode.
MegaCli -AdpSetProp -DsblCacheBypass -val -aN|-a0,1,2|-aALL
val - 0=Enable Cache Bypass.
1=Disable Cache Bypass.
MegaCli -AdpSetProp -LoadBalanceMode -val -aN|-a0,1,2|-aALL
val - 0=Auto Load balance mode.
1=Disable Load balance mode.
MegaCli -AdpSetProp -UseFDEOnlyEncrypt -val -aN|-a0,1,2|-aALL
val - 0=FDE and controller encryption (if HW supports) is allowed.
1=Only support FDE encryption, disallow controller encryption.
MegaCli -AdpSetProp -PrCorrectUncfgdAreas -val -aN|-a0,1,2|-aALL
val - 0= Correcting Media error during PR is disabled.
1=Correcting Media error during PR is allowed.
MegaCli -AdpSetProp -DefaultSnapshotSpace -XaN|-a0,1,2|-aALL
where X is the percentage of the source VD size.
MegaCli -AdpSetProp -DefaultViewSpace -XaN|-a0,1,2|-aALL
where X is the percentage of the source VD size.
MegaCli -AdpSetProp -AutoSnapshotSpace -XaN|-a0,1,2|-aALL
where X is the percentage of the source VD size.
MegaCli -AdpSetProp -DsblSpinDownHSP -val -aN|-a0,1,2|-aALL
val - 0= Spinning down the Hot Spare is enabled.
1=Spinning down the Hot Spare is disabled.
MegaCli -AdpSetProp -DefaultLdPSPolicy -Automatic| -None | -Maximum| -MaximumWithoutCaching -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -DisableLdPS -interval n1 -time n2 -aN|-a0,1,2|-aALL
where n1 is the number of hours beginning at time n2
where n2 is the number of minutes from 12:00am
MegaCli -AdpSetProp -ENABLEEGHSP -val -aN|-a0,1,2|-aALL
val - 0= Disabled Emergency GHSP.
1= Enabled Emergency GHSP.
MegaCli -AdpSetProp -ENABLEEUG -val -aN|-a0,1,2|-aALL
val - 0= Disabled Emergency UG as Spare.
1= Enabled Emergency UG as Spare.
MegaCli -AdpSetProp -ENABLEESMARTER -val -aN|-a0,1,2|-aALL
val - 0= Disabled Emergancy Spare as Smarter.
1= Enabled Emergancy Spare as Smarter.
MegaCli -AdpSetProp -DPMenable -val -aN|-a0,1,2|-aALL
val - 0=Disable Drive Performance Monitoring .
1=Enable Drive Performance Monitoring.
MegaCli -AdpSetProp -SupportSSDPatrolRead -val -aN|-a0,1,2|-aALL
val - 0=Disable Patrol read for SSD drives .
1=Enable Patrol read for SSD drives.
MegaCli -AdpGetProp CacheFlushInterval | RebuildRate | PatrolReadRate | ForceSGPIO
| BgiRate | CCRate | ReconRate | SpinupDriveCount | SpinupDelay
| CoercionMode | ClusterEnable | PredFailPollInterval | BatWarnDsbl
| EccBucketSize | EccBucketLeakRate | EccBucketCount | AbortCCOnError
| AlarmDsply | SMARTCpyBkEnbl | SSDSMARTCpyBkEnbl | NCQDsply
| MaintainPdFailHistoryEnbl | RstrHotSpareOnInsert
| EnblSpinDownUnConfigDrvs | DisableOCR
| BootWithPinnedCache | enblPI |PeventPIImport | AutoEnhancedImportDsply | AutoDetectBackPlaneDsbl
| CopyBackDsbl | LoadBalanceMode | UseFDEOnlyEncrypt | WBSupport | EnableJBOD
| DsblCacheBypass | ExposeEnclDevicesEnbl | SpinDownTime | PrCorrectUncfgdAreas
| UseDiskActivityforLocate | ENABLEEGHSP | ENABLEEUG | ENABLEESMARTER | Perfmode | -DPMenable -aN|-a0,1,2|-aALL
| DefaultSnapshotSpace |
| DefaultViewSpace |
| AutoSnapshotSpace |
| DefaultLdPSPolicy | DisableLdPsInterval | DisableLdPsTime | SpinUpEncDrvCnt
| SpinUpEncDelay | PrCorrectUncfgdAreas
| DsblSpinDownHSP | SupportSSDPatrolRead -aN|-a0,1,2|-aALL
MegaCli -AdpAllInfo -aN|-a0,1,2|-aALL
MegaCli -AdpGetTime -aN|-a0,1,2|-aALL
MegaCli -AdpSetTime yyyymmdd hh:mm:ss -aN
MegaCli -AdpSetVerify -f fileName -aN|-a0,1,2|-aALL
MegaCli -AdpBIOS -Enbl |-Dsbl | -SOE | -BE | EnblAutoSelectBootLd | DsblAutoSelectBootLd | -Dsply -aN|-a0,1,2|-aALL
MegaCli -AdpBootDrive {-Set {-Lx | -physdrv[E0:S0]}} | {-Unset {-Lx | -physdrv[E0:S0]}} |-Get -aN|-a0,1,2|-aALL
MegaCli -AdpAutoRbld -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL
MegaCli -AdpCacheFlush -aN|-a0,1,2|-aALL
MegaCli -AdpPR -Dsbl|EnblAuto|EnblMan|Start|Suspend|Resume|Stop|In fo|SSDPatrolReadEnbl |SSDPatrolReadDsbl
|{SetDelay Val}|{-SetStartTime yyyymmdd hh}|{maxConcurrentPD Val} -aN|-a0,1,2|-aALL
MegaCli -AdpCcSched -Dsbl|-Info|{-ModeConc | -ModeSeq [-ExcludeLD -LN|-L0,1,2]
[-SetStartTime yyyymmdd hh ] [-SetDelay val ] } -aN|-a0,1,2|-aALL
MegaCli -AdpCcSched -SetStartTime yyyymmdd hh -aN|-a0,1,2|-aALL
MegaCli -AdpCcSched -SetDelay val -aN|-a0,1,2|-aALL
MegaCli -FwTermLog -BBUoff|BBUoffTemp|BBUon|BBUGet|Dsply|Clear -aN|-a0,1,2|-aALL
MegaCli -AdpAlILog -aN|-a0,1,2|-aALL
MegaCli -AdpDiag [val] -aN|-a0,1,2|-aALL
val - Time in second.
MegaCli -AdpGetPciInfo -aN|-a0,1,2|-aALL
MegaCli -AdpShutDown -aN|-a0,1,2|-aALL
MegaCli -PDList -aN|-a0,1,2|-aALL
MegaCli -PDGetNum -aN|-a0,1,2|-aALL
MegaCli -pdInfo -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PDOnline -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PDOffline -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PDMakeGood -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL
MegaCli -PDMakeJBOD -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PDHSP {-Set [-Dedicated [-ArrayN|-Array0,1,2...]] [-EnclAffinity] [-nonRevertible]}
|-Rmv -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PDRbld -Start|-Stop|-Suspend|-Resume|-ShowProg |-ProgDsply
-PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PDClear -Start|-Stop|-ShowProg |-ProgDsply
-PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PdLocate {[-start] | -stop} -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PdMarkMissing -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PdGetMissing -aN|-a0,1,2|-aALL
MegaCli -PdReplaceMissing -physdrv[E0:S0] -arrayA, -rowB -aN
MegaCli -PdPrpRmv [-UnDo] -physdrv[E0:S0] -aN|-a0,1,2|-aALL
MegaCli -EncInfo -aN|-a0,1,2|-aALL
MegaCli -EncStatus -aN|-a0,1,2|-aALL
MegaCli -PhyInfo -phyM -aN|-a0,1,2|-aALL
MegaCli -PhySetLinkSpeed -phyM -speed -aN|-a0,1,2|-aALL
MegaCli -PdFwDownload [offline][ForceActivate] {[-SataBridge] -PhysDrv[0:1] }|{-EncdevId[devId1]} -f <filename> -aN|-a0,1,2|-aALL
MegaCli -LDInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
MegaCli -LDSetProp {-Name LdNamestring} | -RW|RO|Blocked|RemoveBlocked | WT|WB|ForcedWB [-Immediate] |RA|NORA|ADRA
| Cached|Direct | -EnDskCache|DisDskCache | CachedBadBBU|NoCachedBadBBU
-Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
MegaCli -LDSetPowerPolicy -Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching
-Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
MegaCli -LDGetProp -Cache | -Access | -Name | -DskCache | -PSPolicy | Consistency -Lx|-L0,1,2|-LALL
-aN|-a0,1,2|-aALL
MegaCli -LDInit {-Start [-full]}|-Abort|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
MegaCli -LDCC {-Start [-force]}|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
MegaCli -LDBI -Enbl|-Dsbl|-getSetting|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
MegaCli -LDRecon {-Start -rX [{-Add | -Rmv} -Physdrv[E0:S0,...]]}|-ShowProg|-ProgDsply
-Lx -aN
MegaCli -LdPdInfo -aN|-a0,1,2|-aALL
MegaCli -LDGetNum -aN|-a0,1,2|-aALL
MegaCli -LDBBMClr -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
MegaCli -getLdExpansionInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
MegaCli -LdExpansion -pN -dontExpandArray -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
MegaCli -GetBbtEntries -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
MegaCli -Cachecade -assign|-remove -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
MegaCli -CfgLdAdd -rX[E0:S0,E1:S1,...] [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
[CachedBadBBU|NoCachedBadBBU] [-szXXX [-szYYY ...]]
[-strpszM] [-Hsp[E0:S0,...]] [-AfterLdX] [-Force]|[FDE|CtrlBased]
[-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI]-aN
MegaCli -CfgCacheCadeAdd [-rX] -Physdrv[E0:S0,...] {-Name LdNamestring} [WT|WB|ForcedWB] [-assign -LX|L0,2,5..|LALL] -aN|-a0,1,2|-aALL
MegaCli -CfgEachDskRaid0 [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
[CachedBadBBU|NoCachedBadBBU] [-strpszM]|[FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN|-a0,1,2|-aALL
MegaCli -CfgClr [-Force] -aN|-a0,1,2|-aALL
MegaCli -CfgDsply -aN|-a0,1,2|-aALL
MegaCli -CfgCacheCadeDsply -aN|-a0,1,2|-aALL
MegaCli -CfgLdDel -LX|-L0,2,5...|-LALL [-Force] -aN|-a0,1,2|-aALL
MegaCli -CfgCacheCadeDel -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL
MegaCli -CfgFreeSpaceinfo -aN|-a0,1,2|-aALL
MegaCli -CfgSpanAdd -r10 -Array0[E0:S0,E1:S1] -Array1[E0:S0,E1:S1] [-ArrayX[E0:S0,E1:S1] ...]
[WT|WB] [NORA|RA|ADRA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU]
[-szXXX[-szYYY ...]][-strpszM][-AfterLdX][-Force]|[FDE|CtrlBased]
[-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] -aN
MegaCli -CfgSpanAdd -r50 -Array0[E0:S0,E1:S1,E2:S2,...] -Array1[E0:S0,E1:S1,E2:S2,...]
[-ArrayX[E0:S0,E1:S1,E2:S2,...] ...] [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
[CachedBadBBU|NoCachedBadBBU][-szXXX[-szYYY ...]][-strpszM][-AfterLdX][-Force]|
[FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] -aNMegaCli -CfgSpanAdd -r60 -Array0[E0:S0,E1:S1,E2:S2,E3,S3...] -Array1[E0:S0,E1:S1,E2:S2,E3,S3...]
[-ArrayX[E0:S0,E1:S1,E2:S2,E3,S3...] ...] [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
[CachedBadBBU|NoCachedBadBBU][-szXXX[-szYYY ...]][-strpszM][-AfterLdX][-Force]|
[FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] -aNMegaCli -CfgAllFreeDrv -rX [-SATAOnly] [-SpanCount XXX] [WT|WB] [NORA|RA|ADRA]
[Direct|Cached] [CachedBadBBU|NoCachedBadBBU] [-strpszM]
[-HspCount XX [-HspType -Dedicated|-EnclAffinity|-nonRevertible]]|
[FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] -aN
MegaCli -CfgSave -f filename -aN
MegaCli -CfgRestore -f filename -aN
MegaCli -CfgForeign -Scan | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL
MegaCli -CfgForeign -Dsply [x] | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL
MegaCli -CfgForeign -Preview [x] | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL
MegaCli -CfgForeign -Import [x] | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL
MegaCli -CfgForeign -Clear [x]|[-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL
x - index of foreign configurations. Optional. All by default.
MegaCli -AdpEventLog -GetEventLogInfo -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -GetEvents {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -GetSinceShutdown {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -GetSinceReboot {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -IncludeDeleted {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -GetLatest n {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -GetCCIncon -f <fileName> -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -Clear -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -GetBbuStatus -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -GetBbuCapacityInfo -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -GetBbuDesignInfo -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -GetBbuProperties -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -BbuLearn -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -BbuMfgSleep -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -BbuMfgSeal -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -getBbumodes -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -SetBbuProperties -f <fileName> -aN|-a0,1,2|-aALL
MegaCli -AdpBbuCmd -GetGGEEPData offset [Hexaddress] NumBytes n -aN|-a0,1,2|-aALL
MegaCli -AdpFacDefSet -aN
MegaCli -AdpFwFlash -f filename [-NoSigChk] [-NoVerChk] [-FWTYPE n] -aN|-a0,1,2|-aALL
MegaCli -AdpGetConnectorMode -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL
MegaCli -AdpSetConnectorMode -Internal|-External|-Auto -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL
MegaCli -PhyErrorCounters -aN|-a0,1,2|-aALL
MegaCli -DirectPdMapping -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL
MegaCli -PDCpyBk -Start -PhysDrv[E0:S0,E1:S1] -aN|-a0,1,2|-aALL
MegaCli -PDCpyBk -Stop|-Suspend|-Resume|-ShowProg|-ProgDsply -PhysDrv[E0:S0] -aN|-a0,1,2|-aALL
MegaCli -PDInstantSecureErase -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL
MegaCli -CfgSpanAdd -rX -array0[E0:S1,E1:S1.....] array1[E0:S1,E1:S1.....] -szxxx -enblPI -aN|-a0,1,2|-aALL
MegaCli -AdpSetVerify -f verify.txt -aN|-a0,1,2|-aALL
MegaCli -LDMakeSecure -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
MegaCli -DestroySecurityKey | [-Force] -aN
MegaCli -CreateSecurityKey -SecurityKey sssssssssss | [-Passphrase sssssssssss] |[-KeyID kkkkkkkkkkk] -aN
MegaCli -CreateSecurityKey useEKMS -aN
MegaCli -ChangeSecurityKey -OldSecurityKey sssssssssss | -SecurityKey sssssssssss|
[-Passphrase sssssssssss] | [-KeyID kkkkkkkkkkk] -aN
MegaCli -ChangeSecurityKey -SecurityKey sssssssssss|
[-Passphrase sssssssssss] | [-KeyID kkkkkkkkkkk] -aN
MegaCli -ChangeSecurityKey useEKMS -OldSecurityKey sssssssssss -aN
MegaCli -ChangeSecurityKey -useEKMS -aN
MegaCli -GetKeyID [-PhysDrv[E0:S0]] -aN
MegaCli -SetKeyID -KeyID kkkkkkkkkkk -aN
MegaCli -VerifySecurityKey -SecurityKey sssssssssss -aN
MegaCli -GetPreservedCacheList -aN|-a0,1,2|-aALL
MegaCli -DiscardPreservedCache -Lx|-L0,1,2|-Lall -force -aN|-a0,1,2|-aALL

sssssssssss - It must be between eight and thirty-two
characters and contain at least one number,
one lowercase letter, one uppercase
letter and one non-alphanumeric character.
kkkkkkkkkkk - Must be less than 256 characters.
MegaCli -Snapshot -Enbl -szXXX SnapshotRepositoryLD N [-AutoSnapshot] [-AutoDeleteOldestSnapshot] -Lx -aN|-a0,1,2|-aALL
MegaCli -Snapshot -Setprop {-AutoSnapshot -val} | {-AutoDeleteOldestSnapshot -val} -Lx -aN|-a0,1,2|-aALL
MegaCli -Snapshot -Dsbl -Lx -aN|-a0,1,2|-aALL
MegaCli -Snapshot -TakeSnapshot [-SnapshotName NameString] [-CreateView [-viewName NameString] [-RW|RO|Blocked] -szXXX] -Lx|-L0,1,2 -aN|-a0,1,2|-aALL
MegaCli -Snapshot -DeleteSnapshot -SnapshotTime yyyymmdd hh:mm:ss | -all [-Force|-Y] -Lx|L0,1,2 -aN|-a0,1,2|-aALL
MegaCli -Snapshot -CreateView -SnapshotTime yyyymmdd hh:mm:ss [-viewName NameString] [-RW|RO|Blocked] -szXXX -Lx -aN|-a0,1,2|-aALL
MegaCli -Snapshot -DeleteView [-SnapshotTime yyyymmdd hh:mm:ss] -Lx -aN|-a0,1,2|-aALL
MegaCli -Snapshot -Info [-SnapshotTime yyyymmdd hh:mm:ss | -ViewTime yyyymmdd hh:mm:ss] -Lx -aN|-a0,1,2|-aALL
MegaCli -Snapshot -Clean -Lx -aN|-a0,1,2|-aALL
MegaCli -Snapshot -GetViewInfo [-ViewTargetId N ] -aN|-a0,1,2|-aALL
MegaCli -ShowSummary [-f filename] -aN
MegaCli -ELF -GetSafeId -aN|-a0,1,2|-aALL
MegaCli -ELF -ControllerFeatures -aN|-a0,1,2|-aALL
MegaCli -ELF -Applykey key <-val> [Preview] -aN|-a0,1,2|-aALL
MegaCli -ELF -TransferToVault -aN|-a0,1,2|-aALL
MegaCli -ELF -DeactivateTrialKey -aN|-a0,1,2|-aALL
MegaCli -ELF -ReHostInfo -aN|-a0,1,2|-aALL
MegaCli -ELF -ReHostComplete -aN|-a0,1,2|-aALL
MegaCli -LDViewMirror -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
MegaCli -LDJoinMirror -DataSrc <val> [-force] -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
MegaCli -SecureErase
Start[
Simple|
[Normal [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]|
[Thorough [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]]
| Stop
| ShowProg
| ProgDsply
[-PhysDrv [E0:S0,E1:S1,...] | -Lx|-L0,1,2|-LALL] -aN|-a0,1,2|-aALL
MegaCli -Version -Cli|-Ctrl|-Driver|-Pd -aN|-a0,1,2|-aALL
MegaCli -Perfmon {-start -interval <val>} | {stop} | {-getresults -f <Filename>} -aN
MegaCli -DpmStat -Dsply {lct | hist | ra | ext } [-physdrv[E0:S0]] -aN|-a0,1,2|-aALL
MegaCli -DpmStat -Clear {lct | hist | ra | ext } -aN|-a0,1,2|-aALL

Note: The directly connected drives can be specified as [:S]

Wildcard '?' can be used to specify the enclosure ID for the drive in the
only enclosure without direct connected device or the direct connected
drives with no enclosure in the system.

Note:[-aALL] option assumes that the parameters specified are valid
for all the Adapters.

The following options may be given at the end of any command above:

[-Silent] [-AppLogFile filename] [-NoLog] [-page[N]]
[-] is optional.
N - Number of lines per page.

[mobilenvidia]

Megarec the staple app for crossflashing, changing SBR etc, or even reviving a card with Firmware issues.
Here are the commands:


MegaRAID HWR Contoller Recovery tool. Version 01.01-004 February 05, 2010
Copyright (c) 2006-2008 LSI Corp.
Supports 1078 controller and its Successors.
Usage:
MegaRec -help : Display the list of options
MegaRec -adpList : Display identified MR controller(s)
MegaRec -corruptInfo : Display corruption information of controller
MegaRec -m0flash <n> <image> : Flash controller
: where <n> is the controller index
: and <image> is the image file to flash
MegaRec -cleanflash <n> <image> : Erase Flash. Programs if image is Provided.
: where <n> is the controller index
: and <image> is the image file to flash
MegaRec -readspd <n> <image> : Read controller SPD to specified file
: where <n> is the controller index
: and <image> is the specified file name
MegaRec -writespd <n> <image> : Write controller SPD from specified file
: where <n> is the controller index
: and <image> is the specified file name
MegaRec -readsbr <n> <image> : Read controller SBR to specified file
: where <n> is the controller index
: and <image> is the specified file name
MegaRec -writesbr <n> <image> : Write controller SBR from specified file
: where <n> is the controller index
: and <image> is the specified file name

[mobilenvidia]

The little app good for modifying the settings ini is megaoem (DOS only), here are its commands:


MegaOEM Ver 8.00.11 December 21, 2009

(c)Copyright 2009, LSI Corporation, All Rights Reserved.


NOTE: The following options may be given at the end of any command below:

[-Silent] [-AppLogFile filename] [-NoLog] [-page[N]]
[-] is optional.
N - Number of lines per page.

MegaOEM -v
MegaOEM -help|-h|?
MegaOEM -adpCount
MegaOEM -AdpAllInfo -aN|-a0,1,2|-aALL
MegaOEM -AdpSetSASA xxxxxxxxxxxxxxxx -aN
MegaOEM -AdpSettings Read | Write -f FileName -aN
-Read - reads INI file, forms MFC_DEFAULT structure and sends it to the FW.
-Write - reads MFC_DEFAULT structure and creates an INI file
MegaOEM -AdpMfgSet -f fileName -aN
MegaOEM -AdpSetVerify -f fileName -aN|-a0,1,2|-aALL
MegaOEM -AdpSetVerifyRaw -f fileName -aN|-a0,1,2|-aALL
MegaOEM -AdpSetSubOEMId XX -aN
XX - sub-OEM ID in Hexadecimal.
MegaOEM -AdpGetSubOEMId -aN
MegaOEM -adpUpdatePersistentPage -f filename - aN
MegaOEM -AdpNVRAM {-Read | -Write -f FileName}|-Clear
[-StartOffset 0xXXXX ] [-EndOffset 0xXXXX] -aN

Note:[-aALL] option assumes that the parameters specified are valid
for all the Adapters.

The following options may be given at the end of any command above:

[-Silent] [-AppLogFile filename] [-NoLog] [-page[N]]
[-] is optional.
N - Number of lines per page.

[mobilenvidia]

SAS2FLASH another very useful app with a gazillion commands, you need this to burn LSI9211 FW and BIOS files, here are its commands:


LSI Corporation SAS2 Flash Utility
Version 11.00.00.00 (2011.08.22)
Copyright (c) 2008-2011 LSI Corporation. All rights reserved

No LSI SAS adapters found! Limited Command Set Available!
-c x: Choose adapter by index
x = index of the adapter to choose (in hexadecimal)

-cpci x: Choose adapter by PCI Address
x = string indicating PCI Address
Must be in format segment:bus:dev:func (segment optional)

-testssid x: Verify adapter by SSVID and SSDID
x = string indicating SSVID and SSDID
Must be in format SSVID:SSDID

-verbose: Set output to verbose mode

-s: Set output to silent mode

-l x: Log all output to file
x = the name of the log file

-f x: Flash firmware image
x = the firmware file to flash


Press ENTER To Continue. Q to quit... -fwall x: Flash firmware image to all adapters
x = the firmware file to flash

-b x: Flash BIOS image
x = the BIOS image to flash

-biosall x: Flash BIOS image to all adapters
x = the bios image to flash

-listall: List information on all LSI SAS Controllers found

-list: List detailed information about the selected SAS controller

-listsasadd: List the SAS address for the selected SAS controller

-ufirmware x: Upload the current firmware to file x

-ubios x: Upload the bios area to file x

-ver: Display the version information for SASFlash

Finished Processing Commands Successfully.
Exiting SAS2Flash.
LSI Corporation SAS2 Flash Utility
Version 11.00.00.00 (2011.08.22)
Copyright (c) 2008-2011 LSI Corporation. All rights reserved

No LSI SAS adapters found! Limited Command Set Available!
Advanced Mode Set

-c x: Choose adapter by index
x = index of the adapter to choose (in hexadecimal)

-cpci x: Choose adapter by PCI Address
x = string indicating PCI Address
Must be in format segment:bus:dev:func (segment optional)

-testssid x: Verify adapter by SSVID and SSDID
x = string indicating SSVID and SSDID
Must be in format SSVID:SSDID

-verbose: Set output to verbose mode

-s: Set output to silent mode

-l x: Log all output to file
x = the name of the log file

-f x: Flash firmware image
x = the firmware file to flash


Press ENTER To Continue. Q to quit... -fwall x: Flash firmware image to all adapters
x = the firmware file to flash

-b x: Flash BIOS image
x = the BIOS image to flash

-biosall x: Flash BIOS image to all adapters
x = the bios image to flash

-listall: List information on all LSI SAS Controllers found

-list: List detailed information about the selected SAS controller

-listsasadd: List the SAS address for the selected SAS controller

-ufirmware x: Upload the current firmware to file x

-ubios x: Upload the bios area to file x

-ver: Display the version information for SASFlash


Press ENTER To Continue. Q to quit... -e x: Erase selected controller's flash region
x = Segment(s) of flash to erase
1 . . . Erase NVSRAM
2 . . . Erase Backup Firmware
3 . . . Erase Persistent Pages including Manufacturing Pages
4 . . . Manufacturing Parameter Block
5 . . . Boot Services
6 . . . Clean Flash (erase all except Manufacturing Parameter Block)
7 . . . Erase Complete Flash
8 . . . Erase MegaRAID Firmware

-vpd x: Program the selected controller with VPD
x = VPD file to parse

-showvpd: Displays contents of the Vital Product Data for the
selected SAS controller

-eth x: Program the selected controller's Ethernet page
x = Ethernet file to parse


Press ENTER To Continue. Q to quit... -showeth: Displays contents of the Ethernet Page Data for the
selected SAS controller

-sasadd x: Program the selected controller with a SAS Address
x = SAS Address to program

-scanchar x: Define character to denote start of a valid SAS Address
x = the final character preceeding the SAS Address

-sasaddhi x: Program selected controller with partial SAS Address
x = First 7 bytes of the SAS Address to program
User will be prompted for remaining SAS Address

-assem x: Program the selected controller with an assembly value
x = Assembly value

-tracer x: Program the selected controller with a board tracer
x = Tracer value


Press ENTER To Continue. Q to quit... -unvdata x: Upload the current nvdata to file x

-ufwbackup x: Upload the backup fw area to file x

-uflash x: Upload the entire flash contents to file x

-reset: Reset selected adapter

-resetall: Reset all adapters

-testfw x: Test firmware version
x = Firmware version to test in xx.xx.xx.xx format

-testbios x: Test bios version
x = BIOS version to test in xx.xx.xx.xx format


Press ENTER To Continue. Q to quit... -testls x y: Test link status of a specific PHY
x = PHY number to test
y = Link status value
Valid Link status values are:
0 - Link Down
1 - 1.5 Gbps
2 - 3.0 Gbps
3 - 6.0 Gbps

-testlsall: List link state on all PHY's on selected controller

-testprodid x: Test selected controller's product id against input
x = Product Id to test in 0x0000 format

-testnvram size: Test selected controller's NVRAM for given size
size = NVRAM size to test

-dflash x y: Download complete flash on selected controller
x = Complete flash image file to be flashed
y = Valid firmware file to be used to flash