View Full Version : Soltek DRV5 v-mod ?
Micutzu
08-19-2002, 12:05 PM
Find the HIP6301 chip , it's near the CPU and voltage regulators . Solder a 10k resistor between pins 7 and 9 . 1.85V should now be 2.2V . Here's the pic :
Micutzu
08-24-2002, 12:47 AM
How's it working ? Did it help you much ?
not done it yet, will let you know as soon as :)
Originally posted by Micutzu20
Find the HIP6301 chip , it's near the CPU and voltage regulators . Solder a 10k resistor between pins 7 and 9 . 1.85V should now be 2.2V . Here's the pic :
Nice picture ;)
m_kelder
11-30-2002, 11:57 PM
what is the vmem mod?
Micutzu
12-01-2002, 09:09 AM
I have't tried one yet , you can use the hidden 2.8v setting , that's enough for me . For this you set both vmem jumpers to the 2-3 position .
m_kelder
12-01-2002, 11:24 AM
It sucks, but for me my 2.5v line is down for some reason I can't figure out but every setting I put it to it is actually lower. At 2.8v setting I get 2.75 and I need more :)
m_kelder
12-01-2002, 11:27 AM
Oh, and just to note, I vmodded my board a little differently. I just copied what I did to my iwill kk266 that has the same chip. I connected a line to pin 7 with a 4.6k resistor and grounded it. Does the same thing, 1.85=2.2
Micutzu
12-01-2002, 11:54 AM
Yeah , i know that many drv5's are undervolted on the vmem line .
And pin9 of the 6301 is gnd in fact .
Sysak
02-06-2003, 05:12 PM
Any idea for Sl-75drv5-c ??????
Micutzu
02-07-2003, 09:39 AM
It should be the same , doesn't it use the same chip (6301) ?
Sysak2
02-08-2003, 07:09 AM
It have 3 small chip and doesn't have BIG CHIP (6301) :(
?????????????????????????????????????????????????? ?
1600xp - 1630Mhz 1,85V 75drv5-c
Micutzu
02-08-2003, 07:58 AM
Well it depends then , what chips are those?
Sysak2
02-08-2003, 02:39 PM
http://c:\75drv5-c.jpg
ยงยงยงยง this forum.
There is 3.small chips. (NON 2.smalls and 1.BIG CHIP)
I don't know what is 3small chips.
sl-75drv5-C*
Micutzu
02-08-2003, 05:13 PM
can't see any pic ... Write down what it says on the chips .
Sysak2
02-09-2003, 07:09 AM
In Soltek Sl-75drv5-c is HIP6302CB
Please Help ME !!
Before A1600@1658Mhz WC 256Mb Infineon
After A1700@2220Mhz WC 256Mb Infineon
I WANT 2V !!!!! !!!! !!! !! !
Sysak2
04-07-2003, 08:49 AM
ANYBODY HELP !!!
Micutzu
04-07-2003, 09:08 AM
It's the same mod for the 6302 ....
Sysak2
04-07-2003, 09:43 AM
HIP6302CB doesen't have 20 legs. This chip have 16 legs.
This look like this
..........
6301
..........
and
........
6302
........
and I don't know were put resistor.
....... - are legs
Micutzu
04-07-2003, 10:10 AM
Doesn't matter , same mod . The 7 and 9 pins are the same ...
http://www.intersil.com/data/fn/fn4766.pdf
Sysak2
04-07-2003, 10:39 AM
Ok thanks. What resitor i must use ? THANKS THANKS !!!!
Micutzu
04-07-2003, 10:53 AM
10K is enough for 2.1-2.2V
Sysak2
04-07-2003, 11:19 AM
Ok THX for all. I modded the MoBo :)
I hope is my A1700 BO@2400Mhz
THANKS
Micutzu
04-07-2003, 11:22 AM
np , glad it worked , good luck further .
Sysak2
04-07-2003, 12:44 PM
And one more qestion :)
Do you know of the Chipset Mod to this Mobo
and AGP mod to 2V ?
????????????????????????????????????
Micutzu
04-07-2003, 01:15 PM
I don't know.... maybe i would figure it out but i don't have the time....
Sysak2
04-07-2003, 01:34 PM
Ok. If you after future got any information of modding chipset and AGP send me email: powerful3d@wp.pl
Thx.