800D Blood+ Project

[noeru]

Hello All

Thank you for seeing work the plan ..me.. ..poor...
As for the plan, it thinks about two rajieta by "Corsair Obsidian 800D".
CPU:corei7 920
mobo:EVGA X58 SLI Classified 141-BL-E760-A1
XSPC480and240

■Intel Xeon w3540
■EVGA X58 SLI Classified 141-BL-E760-A1
■Corsair TR3X6G2000C8GTF-DOMINATOR GT 2Gx3
■XFX/GeForce GTX295x2 Quad　SLI
■Intel X25-M Mainstream SATA SSD SSDSA2MH080G2C1x2 raid0
■HGST/HTS723232L9A360x2
■PIONEER DVR-S17J-BK
■case：Corsair Obsidian 800D BLOOD+
■Power：OCZ Z Series Gold 1000w Power Supply
■HYUNDAI W240D
Singl roop 　
■Watercool HEATKILLER CPU Rev3.0
■EK-FB EVGA X58 CLASSIFIED Acetal+Nickel
■MIPS　mch2255
■EK-FC295 GTX SLI - Nickel
■DDLaing DDC 3.25 12 VDC Pumpｘ2 XSPC Premium Laing Dual DDC Clear Acrylic Top
■Alphacool HF 38 Cape Cyclone 250
■Top/XSPC RX480 Bottom/XSPC RX240 x2
■Tygon 3603 1/2" ID (3/4" OD) Clear Tubing/Tygon 3400 1/2" ID (3/4" OD) Black Tubing
■Bitspower Premium G1/4" High Floｗ compression Fitting
■Feser One F1 Cooling Fluid - UV Red+Feser One F1 Cooling Fluid - UV Purple mix
■Sleeve：MDPC・Mylis TECHFLEXinc
■Enamax CLUSTER UCCL12cmx25mmx6:/Cooler Master High Performance 120MM R4 Series RED LEDx4：/Aerocool RS12 Carbon Fiber Edition Redx1：kaze-just-slim　12cmx12mmx3
■aquaero 4.00 USB Fan-Controller, VF-Display/ZALMAN　ZM-MFC1 Plus-BK


98617

98618

99581

99582

99583

[hale88]

yeh another Corsair 800D love it. But can you post some quality pics?

[noeru]

98720
yeh another Corsair 800D love it. But can you post some quality pics?


Brand-new Corsair 800D

[noeru]

To put XSPC480 in the start, the ceiling is processed.

[noeru]

98722To put XSPC480 in the start, the ceiling is processed.

[noeru]

To install 360→480 from here to the ceiling, it processed it.
Bitspower　Radiator Gard Mesh 48098759

98760

98761

In addition, the installing position was moved behind 15mm.
98762

98763

[noeru]

It cuts it here with a jigsaw.
98764

98765
Laser line jigushi
98766

98767

98768

[noeru]

98769
Xspc480
98770

98771

[Khoral]

I was wondering if a 480 could fit in this amazing case, thank you for showing me that it's possible :D

And of course, flagged :D

[noeru]

Thank you.

I install 240 in the bottom as follows.

[Hellmann]

Amazing keep workin', where will u put the other radiator?

[noeru]

To set up 240, I remove 3.5-inch bay.

It is necessary to remove a lot of rivets to detach this.

[noeru]

To set up 240, I remove 3.5-inch bay.

It is necessary to remove a lot of rivets to detach this.

98772
Bitspower Radiator Gard Mesh 480

[Mash]

noeru, your workplace looks like Mirror's Edge hallways ;)
800D is great, good luck with the project.

[hale88]

Nice cut dude...It looks tight

[noeru]

By the next work in the lower part of XSPC240 install it

I remove a shadowbay and empty a vent into the base
98777

98778

98779

98780

[noeru]

98782

98783

98784

98785

[noeru]

I thank for encouragement!

I put XSPC240Radiator at the bottom
98813

98814

98815

98816

98817

[alacheesu]

Looking good so far. :up:

[Weevil]

Subscribed, nice work, I like this case. :up:

My wife likes your puppy in your profile pic, wants to know if that's a miniature dachshund?

[noeru]

Hello Weevil
yes
The child of the third and the fourth of my home is miniature Daks.
she is Dapple color

[Garrett]

I thank for encouragement!

I put XSPC240Radiator at the bottom
98813

98814

98815

98816

98817

I have been waiting for these photos oh yes :up:
Can you tell me how many millimetres you have left if the radiator is on its side?
I bet not even 3mm, right?

You see I want to put 2 Quad radiators in that bottom compartment and the PSU on top (it can be done) so I'm afraid my PA120.4 is a bit too high with its 129mm width...

I would be helped a lot if you could give me that info :)

Great build man, I will follow this one for sure :up:

[Weevil]

Hello Weevil
yes
The child of the third and the fourth of my home is miniature Daks.
she is Dapple color

<------This one here is Pierre, and his uncle Jack is not pictured, they are wire haired miniatures. Love these little guys,

[punkycorsa]

Nice build! Is it possible to sandwich two duals at the bottom?

[Garrett]

It should be, you mean two dual rads on their sides and fans at each side?
I don't see why not :)

[noeru]

It should be, you mean two dual rads on their sides and fans at each side?
I don't see why not :)


I have been waiting for these photos oh yes :up:
Can you tell me how many millimetres you have left if the radiator is on its side?
I bet not even 3mm, right?

You see I want to put 2 Quad radiators in that bottom compartment and the PSU on top (it can be done) so I'm afraid my PA120.4 is a bit too high with its 129mm width...

I would be helped a lot if you could give me that info :)

Great build man, I will follow this one for sure :up:
I owned Black Ice GT Stealth240 and 360; there is it. Was disappointed, but was not able to install these; because is XSPC240： 286x125x58.6mm
Black Ice GT Stealth240： Is 277x133x29.6mm; the height of the bottom as for about 127mm is because is it.

Black Ice GT Stealth 360:397x133x29.6mm
I interfere a power supply at 397mm



<------This one here is Pierre, and his uncle Jack is not pictured, they are wire haired miniatures. Love these little guys,
Thank you she is a family. You are wonderful


It should be, you mean two dual rads on their sides and fans at each side?
I don't see why not :)

I tried it to put two pieces of XSPC, but there is not an air flow.
Therefore I test it in one piece of XSPC240.

[Erklat]

Great work.
It surely takes a lot of guts to fiddle around the 300$ case with jigsaw :up:

How many degrees this second radiator helps?

[noeru]

my power supply：OCZ　Z Series 1000W
Distance of the power supply part
98849

98850

98851

98852

[syc]

Nice solutions :)

[noeru]

Thanks
next stage is securing of the air flow by the processing of a bottom and a horizontal panel.
Moreover, I try to add another piece XSPC240RX to the bottom.

[noeru]

98957

98958

98959

98960

98961

[noeru]

98962

98963

98964

98965

98966

[noeru]

98967

98968

98969

98970

98971

[noeru]

98972

she is airu

[noeru]

Processing of the side panel to secure the bottom of the air flow.

99057

99058

99059

99062

[Serpentarius]

sub'd

impressive side rad placing ... i tot only lian li and tj07 supports it ...

could it fit a 120x3 rad at bottom?

[noeru]

Hello Serpentarius


sub'd

impressive side rad placing ... i tot only lian li and tj07 supports it ...

could it fit a 120x3 rad at bottom?

The place may be possible,
However, the tube becomes more complicated.

Now I have put a 240x2.
99065

[Serpentarius]

Hello Serpentarius



The place may be possible,
However, the tube becomes more complicated.

Now I have put a 240x2.
99065

hmm interesting ... thx for the pic ... :D
it sure clarifies better than those reviews :D

[triggs75]

Amazing job, making me want to purchase one now. Can't wait to see more pics.....

Chad

[noeru]

Not have enough time for work, I'm sorry takes time,
And the bottom up being very narrow, and further work is difficult not to come.

Make the opening of the side panel to get the cold air.

[noeru]

99182

99183

[noeru]

Installed in the bottom two photos hanging XSPC RX240 is time to narrow task.

99184

99185

99186

99187

99188

[noeru]

Next we set up something on the bottom

･OCZ Z1000M
・Laing DDC-3.2 TPMPx2 Top: XSPC Dual Acrylic Top for Laing DDC
・Aquacomputer Flow sensor
・12cm fanx4
･All lines are Tygon R3603 1 / 2 (12,7 mm) x11/16 (17.46mm) is done in.

[triggs75]

Great work. I am going to have to get one of these, I was going to get the Silverstone TJ07, but I like what you are doing with this case better.

From the looks of your RAD's on the bottom, you are not going to have fans on the 2nd RAD?

[noeru]

Great work. I am going to have to get one of these, I was going to get the Silverstone TJ07, but I like what you are doing with this case better.

From the looks of your RAD's on the bottom, you are not going to have fans on the 2nd RAD?

Case TJ-07 is very nice it is!
I had the idea, 800D has been attracted to this case.

Rad is the bottom of the second set in the 12cmfan to `pull`.

[hale88]

So awesome look. Need more update

[HWMB]

What will be your solution for the fan intake and the cooling of the hot swapped drive bay?

Will one of your bottom Rads block the inlet of the fan cover?

[benko]

noeru is it possible to remove the hot-swap bays completly(hpe it can be done with screwdriver?) so that I can put an intake fan instead(what will be max size 140mm?)?

Here is what I am talikng about:
http://i45.tinypic.com/2ihrwao.jpg
http://i48.tinypic.com/118m3ax.jpg

[ShArKo]

Wow looks great dude!!! Show me more :D:D:D:D

[noeru]

noeru is it possible to remove the hot-swap bays completly(hpe it can be done with screwdriver?) so that I can put an intake fan instead(what will be max size 140mm?)?

Here is what I am talikng about:


Hello benko
Thanks for the suggestion! Aha!
Exhaust is very trouble, too.
I am now, SSDx4 in RAID0 + HDDx1 we plan to build the system.
I'm looking for the location of SSD.

[noeru]

Well Where are you placing? ?
99245

[benko]

Hello benko
Thanks for the suggestion! Aha!
Exhaust is very trouble, too.
I am now, SSDx4 in RAID0 + HDDx1 we plan to build the system.
I'm looking for the location of SSD.
So it is possible?
What tool will I need?
Also what fan size will fit there?

[Anemic]

Looks like its comming out really nice! Very sweet looking build, I want to se the ending result!

[noeru]

So it is possible?
What tool will I need?
Also what fan size will fit there?

Oh sorry!
You are welcome to to the HSB with 14cm fan!
To remove a portion of the back you will need a grinder or jigsaw

[Psydrop]

Nice work noeru

[Antioch]

日本にいるの？

[Logitrust]

Nice build so far, waiting for some more updates!

[Osborne3]

Can we please see more pics. I'm currently building with an 800d and need inspiration : )

[Tripiton]

Nice work noeru! My next pc will be built in a 800D and you are answering me many questions with your photos ;-) Thanks!

[noeru]

Nice work noeru
Thank you for watching my work


日本にいるの？
Yes, I'm from Japan！って日本の方に会えるとは！よろしくです。変な英語ですみません


Nice build so far, waiting for some more updates!
Thank you, I'm now waiting for the arrival of several pieces of parts.


Can we please see more pics. I'm currently building with an 800d and need inspiration : )
We will then post a picture


Nice work noeru! My next pc will be built in a 800D and you are answering me many questions with your photos ;-) Thanks!
Thanks 800D case I think that make it hard to enrich the imagination,
It's nice if a little helpful

[noeru]

I thought about where to place the pump
・Laing　DDC3.2ｘ2
・XSPC Dual Acrylic Top for Laing DDC
99325

99326

99327

99328

[noeru]

Airflow thoughts
Akira Makoto flowing from bottom to top, but I thought the room divided down

99330

99331

[Kozato]

I would go with having them in the 5.25" bay.

[mib]

@noeru

I'm against your airflow project. It's agains law of physics.....
In the top of case should be outlet of hot air (hot air goes up) nad in the bottom or lover parts should be air intake. That's a better solution IMO.

[noeru]

I tried two types of power
· ENERMAX REVOLUTION85 + ERV1050EWT
· OCZ Z Series 1000W OCZZ1000
However, ENERMAX REV is 180m / m in size, so I did not want to 160m / m of OCZ chose
99332

99333

99334

[noeru]

I would go with having them in the 5.25" bay.


@noeru

I'm against your airflow project. It's agains law of physics.....
In the top of case should be outlet of hot air (hot air goes up) nad in the bottom or lover parts should be air intake. That's a better solution IMO.

Yes, exactly right!
The top 5.25 bay intake from behind and thought there would be exhausted
But the fresh air than I would like to give rad ・ ・ ・

[Utnorris]

Looking good! I was wondering how to fit two rads in that box and this has given me some great ideas. Awesome job with the modifications, very clean.

[mib]

Yes, exactly right!
The top 5.25 bay intake from behind and thought there would be exhausted
But the fresh air than I would like to give rad ・ ・ ・

I guess that mobo will be also watercooled. So then it produces much less hot air (radiation) then only AC mobo. The difference will not be much different 2-3*C.
The best will be to try both solutions while checking temps.

In my case i got intake in the bottom and air outlet in the top and it works.

[noeru]

Looking good! I was wondering how to fit two rads in that box and this has given me some great ideas. Awesome job with the modifications, very clean.


I guess that mobo will be also watercooled. So then it produces much less hot air (radiation) then only AC mobo. The difference will not be much different 2-3*C.
The best will be to try both solutions while checking temps.

In my case i got intake in the bottom and air outlet in the top and it works.

Thank you for your valuable opinions!

[noeru]

Unified treatment of the black cable very very thanks MDPC!
99543

99544

99545

99546

99547

[noeru]

99548

99549

[noeru]

Received from Performance-PCs and Aquatuning
Line 1 / 2 "ID (3 / 4" OD)

99550

99551

99552

[noeru]

・EVGA EVGA X58 SLI Classified +　EK-FB EVGA X58 CLASSIFIED Acetal+Nickel
・HEATKILLER CPU Rev3.0
・MIPS
99553

99554

99555

[noeru]

And I'm not used to fill the hole mesh cable to the back panel, but Eternal Hot air to dissipate it is important for me.

99558

[noeru]

Once made a formal setup・・・

99565

99566

99567

99568

99570

[noeru]

next　time　Case two rooms to create a block of aluminum　panels

99571

99572

99573

[noeru]

Thank Aquatuning:)
99574

99575

99576

[noeru]

Slave runs out and Topufan
Bitspower G 1 / 4 "Black Sparkle 45 Degree IG 1 / 4" Adapter
Bitspower G 1 / 4 "Black Sparkle 90 Degree IG 1 / 4" Adapter
Cooler Master High Performance 120MM R4 Series RED LED Case Fan
Tygon R3400 1/2" ID (3/4" OD) UV Resistant Tubing - Black
99577

99578

99579

99580

[Weevil]

http://www.xtremesystems.org/forums/attachment.php?attachmentid=99548&d=1260580838

Your dachshunds will thank you to quit smoking cigarettes.

The wires look beautiful BTW. ; )

[noeru]

Your dachshunds will thank you to quit smoking cigarettes.

The wires look beautiful BTW. ; )

Hello Weevil very very thanks
Exactly right! I just now, smoking cigarettes is to stop in the middle of the

[noeru]

This is a test of flow
99584

99585

99593

99594

99596

[noeru]

And decided the line:up:

99588

99590

99591

99592

99589

[Psydrop]

really nice work noeru....

[shadow46x2]

out of curiosity, why the one black line as opposed to all clear or all black?

--j

[buccaneer]

Thanks for sharing your work Noeru! Have an800D here and need ideas.
have some questions:
do you intend to put the mid support foot back under the case? is it sagging or it that the picture?
what made you put the rads outside of the case? not enough room inside or do you yust like it?
Nice work!!

[noeru]

really nice work noeru....
Thank you very, very grateful:)


out of curiosity, why the one black line as opposed to all clear or all black?

--j
Yes! This black line has no special meaning
I tried it out, I will revert to the original Tygon3603;)


Thanks for sharing your work Noeru! Have an800D here and need ideas.
have some questions:
do you intend to put the mid support foot back under the case? is it sagging or it that the picture?
what made you put the rads outside of the case? not enough room inside or do you yust like it?
Nice work!!
Thanks for the question　　Sorry I'm weak in English
Room dividers will be rad support.　
Looking to put the rad? Put the rad outside the case?:confused:

99614

[Weevil]

It's alive!!!

[Weevil]

what made you put the rads outside of the case? not enough room inside or do you yust like it?
Nice work!!

You seem confused, re-read thread from beginning.

[buccaneer]

HI Noeru! Yes confusing you here :) sory for that! Was refering to the rad fans in the top. earlyer you showed all internal. too tight?

[Psydrop]

buccaneer what rad are you talking about? Or has he sent you secret pics i can't see.

[buccaneer]

Ha ha Only now I noticed that those fans are layinh lose on top of the case! indeed confuced me. nice work!!!!!!!

[triggs75]

Very nice set up. Are you running one loop with all? Did you end up using both pumps or just the one. Ca you take a pic of the pumps in the bottom.

Great work

Chad

[Mabyboi]

OOOO how are those fans?! i was looking at those. are they actually silent? can we get more pics of em?

[Osterman]

Pretty nice work!.
I would like to ask you, which is the trip that the coolant makes on your system? and also, have you used 1/2 ID 3/4OD compression fittings for your tygon 1/2ID 3/4OD??
About the latter question, I will use the same specifications and well I am a little bit afraid that the compression wont be tight enough.

[exe163]

Amazing job on spacing! I don't think you can put anything more to it.

[allig4t0r]

Great wlog matey :] One question worries me - is your cute dog longer than xspc 480 or not?

[noeru]

It's alive!!!

You seem confused, re-read thread from beginning.
hello Weevil I respect thank you dear represent:)



HI Noeru! Yes confusing you here :) sory for that! Was refering to the rad fans in the top. earlyer you showed all internal. too tight?


buccaneer what rad are you talking about? Or has he sent you secret pics i can't see.
Sorry I'm late:)

It is a thing of the Top rad data XSPC RX480 125mmx58.5mm 25mmFan press - you can :up:

99712

99713

99714

99715



Ha ha Only now I noticed that those fans are layinh lose on top of the case! indeed confuced me. nice work!!!!!!!
thank you　^^;　


Very nice set up. Are you running one loop with all? Did you end up using both pumps or just the one. Ca you take a pic of the pumps in the bottom.
Great work
Chad
Yes, it is one loop. Consider from watching the water temperature to change the loop.
Now DDC3.25x2 XSPC Dual Acrylic Top for Laing DDC is.
99716


OOOO how are those fans?! i was looking at those. are they actually silent? can we get more pics of em?
SSD has taken the time to repair broken away
Yes, I want your photo shows ^ ^


Pretty nice work!.
I would like to ask you, which is the trip that the coolant makes on your system? and also, have you used 1/2 ID 3/4OD compression fittings for your tygon 1/2ID 3/4OD??
About the latter question, I will use the same specifications and well I am a little bit afraid that the compression wont be tight enough.
Thanks for your question if the answer is, I ask you a question again
yes,this Tygon 3603or3400 is 1/2ID 3/4OD This could ensure the flow of many
11/8mm was previously


Amazing job on spacing! I don't think you can put anything more to it.
Thanks If your reference:)

[noeru]

Great wlog matey :] One question worries me - is your cute dog longer than xspc 480 or not?

haha;) airu is 32ｃｍ
she is Kaninchen Dachshund

[noeru]

I was once where I validate the air flow case
http://www.xtremesystems.org/forums/attachment.php?attachmentid=99330&d=1260026065

Conditions: Each bench tests conducted in closed cases
Core I7 920
Xeon W3540
Xeon W3520
OCCT or PrimTHtest(3hr)
99727

99728

99729

[noeru]

Results:
Measurement place 6 points
・Aquatuning Thermosensor In- Out Thread G1/4　x2
　Top rad out　Watertemp　
　botom rad out temp
・Mcubed Thermosensor Push/Plugin Bronze 10mm　ｘ1
Reservoir
・Temperature Sensor　x3
　case out temp
Middle of the case
botom rad out air temp
Flowsensor is
・aquacomputer Flow sensor "high flow" G1/4
・aquacomputer aquaero

aquacomputer Flow sensor
99745

botom rad out temp
99744

99746
OCCT I7 920 4336.3 coreV1.375V
Top rad out　Watertemp: 28.1℃　
botom rad out temp: 27.7℃
Reservoir　temp:27.5℃
case out temp：21.1℃
Middle of the case:25.8℃
botom rad out air temp 26.0℃
Flow 277.12L/hr
Fan is top 980rpm
botom 1000rpm or 1200rpm
99747
Prim (3hr) xeon3540 4519.6 corev 1.376(BIOS1.45)
Top rad out　Watertemp: 26.2℃　
botom rad out temp: 25.8℃
Reservoir　temp:25.8℃
case out temp：21.5℃
Middle of the case:24.7℃
botom rad out air temp 24.7℃
Flow 281.27L/hr
Fan is top 980rpm
botom 1000rpm or 1200rpm
I am pleased with the outcome is:yepp:

[Weevil]

Very nice results! two thumbs up :up::up:

[Sil2]

Noeru, I'm curious on how you got both of the RX240s to fit down the bottom, could we get some more pictures to show how you made them fit?

Did you have to cut a bit of the bottom hole where the grommet was for cable management out?

Cheers

[smanet]

Wow, this is an amazing work. I love this case anche the 480 on top is classy... wish I saw this before buying the RV01. Very very nice!

[noeru]

Very nice results! two thumbs up :up::up:
very　very　thanks Were better than expected results

[noeru]

Noeru, I'm curious on how you got both of the RX240s to fit down the bottom, could we get some more pictures to show how you made them fit?

Did you have to cut a bit of the bottom hole where the grommet was for cable management out?

Cheers
hello Sil2
thank you for getting me interested in the work,I cut the bottom for air flow to the bottom and work.
The piping for the 10mm　rad is the offset.RX240 tried to connect a rotary angle, we stopped for a difficult
'G1 / 4 D-Plug Set-ONE Inch Version' also had enough Specified After all, Tygon are connected.
As work is still processing and front panel wiring.

99771

99772

99773

99774

[noeru]

Wow, this is an amazing work. I love this case anche the 480 on top is classy... wish I saw this before buying the RV01. Very very nice!

hello smanet:) very very thanks:welcome:

[Serpentarius]

Not have enough time for work, I'm sorry takes time,
And the bottom up being very narrow, and further work is difficult not to come.

Make the opening of the side panel to get the cold air.

that's a very thin fan! 15mm thick? what fan is that?

[noeru]

that's a very thin fan! 15mm thick? what fan is that?

hello Serpentarius:)
this fan is KAZE-JYUNI-SLIM　12ｍｍ
http://www.scythe.co.jp/cooler/kaze-jyuni-slim.html

99782

[noeru]

Blood + The work is not finished yet.It is still working・・・

99777

99778

99779

[Baulten]

I really like what you did with the case; it looks really good, better then mine that's for sure ;)

[Sil2]

Thanks for the pictures noeru.

Out of curiousity how did you get the two 240s to stand up cause i've got one at the moment and i just can not get it sit on its side, it keeps on hitting the top of the bottom compartment.

Cheers

EDIT:

Got it in but required a little bit of force :)

[Anemic]

Beautiful build man! Aregatto noerusan for sharing your work!

[noeru]

I really like what you did with the case; it looks really good, better then mine that's for sure ;)

Thanks for watching me without boring:)

[noeru]

Thanks for the pictures noeru.

Out of curiousity how did you get the two 240s to stand up cause i've got one at the moment and i just can not get it sit on its side, it keeps on hitting the top of the bottom compartment.

Cheers

EDIT:

Got it in but required a little bit of force :)

If I indicate if your image will help:up:

[noeru]

Beautiful build man! Aregatto noerusan for sharing your work!
Thanks! It's nice that you admire from:D

[noeru]

100003

100006

100007

100008

100009

[whuzabi]

looks good but the colour of the tubes are not so good :/ is thin 1/2" tube ?

i think i know wich sys was your inspiration ;)

[noeru]

100010

100011

100012

100013

[noeru]

looks good but the colour of the tubes are not so good :/ is thin 1/2" tube ?

i think i know wich sys was your inspiration ;)

Thanks!:)
this tube is 1/2 (3/8)

[Weevil]

The colours look perfect to me!

B-E-A-UTIFUL! Nice job! :clap::clap::clap:

[noeru]

The colours look perfect to me!

B-E-A-UTIFUL! Nice job! :clap::clap::clap:

Weevil! veryvery thanks always! I have to thank you.:D

[Raiden]

Beautifull !

But it looks a lot as Malik´s .. you must be inspired by him LOL

Anyway awesome case and everything looks good.

[noeru]

Beautifull !

But it looks a lot as Malik´s .. you must be inspired by him LOL

Anyway awesome case and everything looks good.

very thanks:)
^^ Yes, the PC is in like with Malik's.
Thing that is certainly influenced by him.:yepp:

[noeru]

Flat for illumination and inspection work in the case of LED (12V) was established.
This can be verified, such as leaks.
And this is the ZALMAN fan-con is connected to, can come to adjust the brightness.:up:

100020


100021


100022

[triggs75]

Very Very nice. Great build

Chad

[charles_h]

Very nice noeru, fantastic work and photos! :up:

[noeru]

Very Very nice. Great build

Chad

very very thank you If i help you, i'm happy:)

[noeru]

Very nice noeru, fantastic work and photos! :up:

veryvery Thanks! charles's words makes me glad:up:

[Psydrop]

noeru i just love your bild you even made me buy the same case. Great work man

[noeru]

noeru i just love your bild you even made me buy the same case. Great work man

veryveryThanks! If I am happy to help you.:)

Please tell the things I needed, I'll help you if you are satisfied with :up:

[noeru]

Mid Night2　800D　BLOOD+

100073


100074


100075


100076

[NAM_killer]

Wow, this is such an inspiring build! congratulations on finishing it, I have been watching this for weeks!

[Psydrop]

looking very nice m8.

[noeru]

Wow, this is such an inspiring build! congratulations on finishing it, I have been watching this for weeks!


looking very nice m8.

hello thank you for watching my work:)
Close Case　room temp 18.5℃ Water temp19.5
try to the max clock:rolleyes:
100150

[Mjhieu]

Wow, Extremely Nice mod. You done a great job. Oh you pushed your cpu to nearly 5ghz. Could you mind to tell me what is the temp of ur cpu at 5ghz?

[Sil2]

Wow, Extremely Nice mod. You done a great job. Oh you pushed your cpu to nearly 5ghz. Could you mind to tell me what is the temp of ur cpu at 5ghz?

Normally people dont take temperatures into consideration when they are going for a suicide shot :)

[noeru]

Wow, Extremely Nice mod. You done a great job. Oh you pushed your cpu to nearly 5ghz. Could you mind to tell me what is the temp of ur cpu at 5ghz?

thanks^^ 　Image is small

100151

[Xion X2]

Nice build. :)

[Mjhieu]

Thanks, :D Amazing Temperatures, I love ur water system :p:


thanks^^ 　Image is small

100151

[Church]

I wonder if it's possible to fit HWLabs Black Ice GT Xtreme 560 monstrous rad (153mm/605mm/54mm) in top of Obsidian 800D in similar way?

[noeru]

I wonder if it's possible to fit HWLabs Black Ice GT Xtreme 560 monstrous rad (153mm/605mm/54mm) in top of Obsidian 800D in similar way?

Hi churchy I think I have a GTX560 this "800D" in order to achieve cut the front panel must
this case is External dimension is 585m/m

100175

100176

100177

100178

[Church]

Big thanks for info/measurements. But how about cutting back of case? So eg. non fan part of rad with tubing attachment holes is outside case (it won't change much looks as it's well .. back :) ) .. IIRC there should be some place for optional top PSU mount? And how about internal width of 5.25 bay enclosure? Can you measure that width of enclosure if it's wide enough to put 153mm wide rad in there or needs to be removed (I don't plan using any 5.25" devices anyway) + if possible, pics of top-back of this case from outside&inside?
P.S. There is another monstrous radiator out there (Watercool Mo-Ra 2 Pro, square form (424 x 385 x 54mm) 3x3 for nine 120mm fans which i considered at one point for installment on the side of case, even quieter and better cooling then gtx 560), or similar Phobya Xtreme NOVA 1080 rad, but most probably installing those will result in ugly looking side of case with fat bump outside dimensions). But in any case .. how wide(deep?) is compartment on the right side of case for cable management?
http://www.hwlabs.com/images/gtx/d_gtx560.jpghttp://www.coolputer.fi/tuotekuvat/1097.jpg

[noeru]

Big thanks for info/measurements. But how about cutting back of case? So eg. non fan part of rad with tubing attachment holes is outside case (it won't change much looks as it's well .. back :) ) .. IIRC there should be some place for optional top PSU mount? And how about internal width of 5.25 bay enclosure? Can you measure that width of enclosure if it's wide enough to put 153mm wide rad in there or needs to be removed (I don't plan using any 5.25" devices anyway) + if possible, pics of top-back of this case from outside&inside?
P.S. There is another monstrous radiator out there (Watercool Mo-Ra 2 Pro, square form (424 x 385 x 54mm) 3x3 for nine 120mm fans which i considered at one point for installment on the side of case, even quieter and better cooling then gtx 560), or similar Phobya Xtreme NOVA 1080 rad, but most probably installing those will result in ugly looking side of case with fat bump outside dimensions). But in any case .. how wide(deep?) is compartment on the right side of case for cable management?


Hi churchy this rad I think this is difficult. Process also requires a five-inch side of the bay　
the inner bay is 5 inches 146.8mm.
I was set 15mm further back than normal
100188

100189

[noeru]

Inner 5.25 bay Front　top

100181


100182


100183


100184


100185

[Church]

Well, seems i'll have to give up on this particular rad and use some 3x140mm or 4x120mm as one you used, as i am aiming to maximise cooling but still staying with everything mounted within case. Thanks for providing info, it will help me greatily with choosing components.
Arigato gozaimasu :)
P.S.
Pitty though. Almost none of current full tower cases by major vendors seem able to accomodate gtx 560. Maybe sometime in future in some next iteration of their cases ..

[Garrett]

Churchy, well I have the PSU on top, I had to drill several rivets to get the roof off... but I use a Lian-Li PSU Extender too :)
I'm buying a new cam tomorrow so until then no pics unfortunately :)
That's how I got 2 Quad rads in the bottom compartment :)

[scgt1]

Nice clean looking setup
Subscribed:up:

[noeru]

Well, seems i'll have to give up on this particular rad and use some 3x140mm or 4x120mm as one you used, as i am aiming to maximise cooling but still staying with everything mounted within case. Thanks for providing info, it will help me greatily with choosing components.
Arigato gozaimasu :)
P.S.
Pitty though. Almost none of current full tower cases by major vendors seem able to accomodate gtx 560. Maybe sometime in future in some next iteration of their cases ..


Churchy, well I have the PSU on top, I had to drill several rivets to get the roof off... but I use a Lian-Li PSU Extender too :)
I'm buying a new cam tomorrow so until then no pics unfortunately :)
That's how I got 2 Quad rads in the bottom compartment :)


Nice clean looking setup
Subscribed:up:

veryvery Thanks:)
There are also some pictures here
I'm noeru (http://noeru-dairu.jugem.jp/):welcome:

[noeru]

Aｄｄ　Picture


100317

100318

100319

100320

100321

[noeru]

100326


100327


100328


100329


100331

[Antioch]

どこに住んでますか？立派なマンションですね。そして、夜景はすごいです！

[IgoRR]

Beautiful build ;)

I like it very much :)

[noeru]

どこに住んでますか？立派なマンションですね。そして、夜景はすごいです！
こんにちはAntioｃｈ何時もありがとう＾＾私の住んで居るのは東シナ海の見える高台です＾ ＾
都市圏ではないのです。
100433



Beautiful build ;)
I like it very much :)
veryvery Thanks:)

[Mansell0050]

All I can say is AWESOME!!!! Just ordered my case based on yours alone....and cos you are extremely polite and answer everyone. Well done, great work....others should take note....

[noeru]

All I can say is AWESOME!!!! Just ordered my case based on yours alone....and cos you are extremely polite and answer everyone. Well done, great work....others should take note....

Hello Mansell0050　Thank you for watching my work;)
I learned a lot in ex　＾＾　i thanks ex all members　.:)

[zigzag]

what a beautiful build, and stunning apartment :)

just got my 800D today, if my build turns out half as nice as yours noeru, i will be happy.........and surprised lol.

congrats!!

[buccaneer]

Hi noeru! congratulations with the end result! Looks great.
Have a question. Dod you have anny alighning problems with the back slots of grafic cards? mine do not realy line up without forcing the back of the case inwards.

[noeru]

what a beautiful build, and stunning apartment :)

just got my 800D today, if my build turns out half as nice as yours noeru, i will be happy.........and surprised lol.

congrats!!

hello zigzag:) 　Please tell me if you can help:)


Hi noeru! congratulations with the end result! Looks great.
Have a question. Dod you have anny alighning problems with the back slots of grafic cards? mine do not realy line up without forcing the back of the case inwards.
hello buccaneer Thanks for the question　
But Sorry, my English is not enough power.:confused:
What is the back plate of VGA?
100498

100499

100500

[noeru]

this"月光-GETUKOU-":D


Corsair Obsidian 800D Mid night BOOLD+ (http://www.youtube.com/watch?v=BXYBYpWlJQ0&feature=player_embedded)　

[insidertrading]

It cuts it here with a jigsaw.
98764

98765
Laser line jigushi
98766

98767

98768

could i ask you what is the model of your jigsaw?

[noeru]

could i ask you what is the model of your jigsaw?

hello insidertrading
my jigsaw? jigsaw is　BOSCH PST680EL　
http://www.bosch.co.jp/jp/pt/products/model.asp?id=PST680EL

[hale88]

Well done ;)

[insidertrading]

hello insidertrading
my jigsaw? jigsaw is　BOSCH PST680EL　
http://www.bosch.co.jp/jp/pt/products/model.asp?id=PST680EL

thanks mate! does it really have laser line tracing?? i tried the whole of today to find one at my local hardware shops but coudnt!

[Osterman]

Nice work but... you should fix the edges of the rear fan hole. It cant be there like that, taking into account the good work you have done with the rest.

[noeru]

Tried to Gulftown EVGA-E760 in
Now it is a shame that we are not yet supported.
BIOS: 43:shrug:
100878

100879

100880

100881

[Afrodisiac]

Very clean work, I like it.

[Raiden]

What you got a Gulftown how?

Damn nice .. good project , wish i had one , Portugal is always left apart :mad::rofl:

[noeru]

Very clean work, I like it.
veryvery thanks:)


What you got a Gulftown how?

Damn nice .. good project , wish i had one , Portugal is always left apart :mad::rofl:
Borrowed from a friend　
ASUS　P6T6WS　or R2E or P6TDT is Work is good:up:

[miahallen]

Very nice build noeru...many of those parts are very difficult to find here...you've had a lot of work putting this thing together, well done :toast:

[Philwong]

Exceptional build from the land of the rising sun!

Are you from Tokyo, Noeru san?

Phil

[noeru]

Very nice build noeru...many of those parts are very difficult to find here...you've had a lot of work putting this thing together, well done :toast:

veryvery thank miahallen, I'm glad you hung voice:p:




Exceptional build from the land of the rising sun!

Are you from Tokyo, Noeru san?

Phil
hello Philwong.:)
No No, I do you live in the southernmost island of Japan ^ ^ half of the island are U.S. Air Force and Navy bases. okinawa you live:D

[Philwong]

No No, I do you live in the southernmost island of Japan ^ ^ half of the island are U.S. Air Force and Navy bases. okinawa you live:D

Ohioguzimus! I'm from Singapore, but is a huge fan of Tokyo and Akihabara.

Phil

[noeru]

Ohioguzimus! I'm from Singapore, but is a huge fan of Tokyo and Akihabara.

Phil

AKB than where you live closer to me in Singapore :)
i'm　AKB is not done only to a few times.:(

[noeru]

next project　
I plan to add XSPC RX480 base. However, it has many problems.
・ Where the power
・Reservoir and pump
・ Single or dual loop
・Top 480x1 bottom 480x1 240x1　These air flow:confused:

101085

101086

101087

101090

101091

[Wezly]

I just don't think you can have it all, my friend.

Have you considered hanging it off the back? :X

[Church]

hmm. Noeru: how about putting PSU on one of it sides and cutting out hole for it's air intake in case side wall (another option to locate it in front of case with power cord extention)? Then place side by side rad (it's hard to tell from these pics, maybe case middle section floor or case bottom needs to be cut for that .. (in both cases possibly strengthening of case structure needed?)). Probably few more hight can be recovered by taking out removable dust filters.
[edit]
hmm. or PSU in front of case, and rad laying on bottom of case? or PSU risen as much as possible till bottom of motherboard? but in such case it will suck warm air from bottom radiator. choices, choices :)

[noeru]

I just don't think you can have it all, my friend.

Have you considered hanging it off the back? :X


hmm. Noeru: how about putting PSU on one of it sides and cutting out hole for it's air intake in case side wall (another option to locate it in front of case with power cord extention)? Then place side by side rad (it's hard to tell from these pics, maybe case middle section floor or case bottom needs to be cut for that .. (in both cases possibly strengthening of case structure needed?)). Probably few more hight can be recovered by taking out removable dust filters.
[edit]
hmm. or PSU in front of case, and rad laying on bottom of case? or PSU risen as much as possible till bottom of motherboard? but in such case it will suck warm air from bottom radiator. choices, choices :)
yes Sure! To solve this problem is a custom I grow up? It is required, removal of Shadoubei bays＆5.25bays , PSU · SSD · HDD I think the aluminum panels and acrylic panels to create.Reworking of the side panel along ・ ・ ・ Umm:shrug:
Bottm is TJ-07 Look? Rad 480X3?? (Bottom480x2 Top480x1):rolleyes:

[felix_w]

Any progress to your project noeru ?

[noeru]

Any progress to your project noeru ?

Hello, felix_w Thanks for watching:)
Now we are together.
"TFC Monsta Extreme Radiator 420" I'm looking for.
What meets the bottom of the TFC rad? How to supply side panels, suffering:(

[skinnee]

Nice worklog! :up:

I noticed the most recent photos that the red in the loop is gone... did is breakdown or did you remove it?

:toast:

[noeru]

Nice worklog! :up:

I noticed the most recent photos that the red in the loop is gone... did is breakdown or did you remove it?

:toast:


Thanks　skinnee:)　 We are slowly trying to change the color:)

[noeru]

We think:rolleyes:
5.25 Bay new even now remains is what should make installation OCZ. Due to its size
I think the best side panels of aluminum and acrylic rebuild.

101853

[felix_w]

Power supply will be placed where the white marked area is ?

And you gonna make new side panels for the 5.25" bay from acrylic ?

[Antioch]

Power supply will be placed where the white marked area is ?

And you gonna make new side panels for the 5.25" bay from acrylic ?

Thats what he's trying to say :D

[felix_w]

Thats what he's trying to say :D

Thanx, i just wanted to verify...:up:

[zigzag]

i wish you luck with this noeru ;)
btw, can i ask you the dimensions of the top rad cut out please? I have the same bitspower grill coming and want to get cutting on my case :).

[charles_h]

Very interesting location for the PSU noeru, I look forward to seeing more. :)

[noob eater4726]

Why stop there? :D

Do dual XSPC's 480s, one each side! :shocked:

[noeru]

Power supply will be placed where the white marked area is ?

And you gonna make new side panels for the 5.25" bay from acrylic ?
PFU Yes, I think the white portion of the inlet from the exhaust before the side panel.


Thats what he's trying to say :D


i wish you luck with this noeru ;)
btw, can i ask you the dimensions of the top rad cut out please? I have the same bitspower grill coming and want to get cutting on my case :).
hi zigzag http://www.xtremesystems.org/forums/showthread.php?t=238950
What is this? Bitos relationship with the size of the cut?

[noeru]

Very interesting location for the PSU noeru, I look forward to seeing more. :)
Hi　charles_h
I'm glad of you interested in you! Thank you very:)


Why stop there? :D

Do dual XSPC's 480s, one each side! :shocked:
If you want to try 480x2+360　:up:

[zigzag]

Hi Noeru! The length and width of your 480 cut out?? I have the same rad aswell, xspc 480. Was hoping to get a head start on the cuts before my bitspower grill arrives :)

[avddreamr]

We think:rolleyes:
5.25 Bay new even now remains is what should make installation OCZ. Due to its size
I think the best side panels of aluminum and acrylic rebuild.

101853

You could do that, and it may even be easier to use one of the new antec psu that are 120mm high, and place the fan their. It would greatly simplify cooling.
Although, I dont think they go up 1000w, but you may not actually need 1000w.

Another idea, is to use one or two rx360 instead. I think you have 572mm on the base to play with. The rx360 is 410mm, so that leaves 172mm to play with. It would still force you to get creative with psu mounting. You could either get a short psu and get very very creative, or fab a psu extender.
Or you could fab up a new psu case to work with that small ammount of space, just depends how comfortable you are with cracking open your psu.

Either way you have your work cut out for you. It's funny, no matter how big a case gets, you always can think of ways of where you just wish it was just a bit bigger.




Amazing build. btw

[noeru]

480x2 is now going to be a little further;)
980X in anyway:p:

103284

[noeru]

103478

intel i7 980X 5027.4MHz (http://noeru-dairu.jugem.jp/)　Water cooling :up:
EVGA X58 SLI Classified 141-BL-E760-A1
Corsair TR3X6G2000C8GTF-DOMINATOR GT 2Gx3
GeForce GTX295x2 Quad　SLI
Intel X25-M Mainstream SATA SSD SSDSA2MH080G2C1x2 raid0
HGST/HTS723232L9A360x2
Corsair Obsidian 800D BLOOD+
OCZ Z Series Gold 1000w Power Supply

[Omarko]

how did you manage to put the RX240 sideways at the bottom ?

once I put it in , I can not turn it around as its too thick

?????

[noeru]

how did you manage to put the RX240 sideways at the bottom ?

once I put it in , I can not turn it around as its too thick

?????

helo Omarko:)
RX240 is I had a hard time;)
Remove the center plate rivets work is easy.Fan and stopped in, you must work under the mouth:)

103534

103535

103536

103537

103538

[ScottALot]

Take some pix of your dachsund! He's so damn cute.

[00011011]

Noeru, great work! you have greatly inspired me on my first water cooled system. I am also using the i7-980x. Obviously the lower the better, but in your opinion (or anyone who could ring in on this) what would you consider the highest core temps you would feel safe for a 24/7 overclock (assuming stable)?

Currently I'm @ 4.3 GHz. I haven't run any overnight tests yet, but after 10 minute small FFT torture tests, my hottest single core temp maxed at 77 at some point, but running average of all six is 72.

And when running Prime95 torture test, which is it best to run? Small FFTs (ram not tested much), In-place large FFTs (max heat, some ram tested), or Blend (lots of ram tested)?

[Gonzalo-Gonads]

Now get it crunching! :cord:

No but really amazing job! :up: I think a 480 rad will be pushing it alittle eh?

P.S. get it crunching ;) that thing would be a beast at wcg :yepp:

[The.Sorrow]

HI

Amazing project dude.

Can u just tell me , is that a conector witch are in the midle of the 1 gt295 and the second, or is a junction of males and females conector?
if its a conector can u just give me the exact name?

I love it,, the look man..

Congratzz :up:

[rioja]

and may you tell me will it be possible to put two 3x120 rads on bottom with16cm psu?

[mlee49]

Love this project, totally inspiring to me! Question, would a 140.3 fit inside the case across the top? I'm debating a single loop w/a 140.3 and a 120.1 for an i7 920 and 2x GF100's.

[Church]

mlee49: I've seen few worklogs with 140.3 on top. Sorry, i'm too lazy to search urls for them. Main thing you should watch for if 140.3 rad's width fits between 5.25 enclosure bays walls. Some 140rads fits (don't remember, XSPC or TFC or something else), some (in particular wider Black Ice GTX/SR1 - do not = required some cutting of top of those 5.25 walls). And of course you need cut top for larger rad and paint cuts or slap some nice rad grill ontop.

[Nage]

and may you tell me will it be possible to put two 3x120 rads on bottom with16cm psu?

have this case and think about it right now so theres 1cm gap only (with RX360 and OCZ PSU)and in this place bunch of wires ATX24 connector. If you can mod your psu - (turn this bunch on 90degrees) I think it possible.

noeru you have this PSU what do you think is it possible put here RX360?

http://www.overclock3d.net/gfx/articles/2009/09/07155701257l.jpg
http://www.overclock3d.net/gfx/articles/2009/09/07155703682l.jpg


also for two rads at bottom you'll need this side panel
https://shop.corsair.com/store/item_view.aspx?id=1171683

[Awers]

Nice build and photo's. But I think the one color light would look better.

[noeru]

Noeru, great work! you have greatly inspired me on my first water cooled system. I am also using the i7-980x. Obviously the lower the better, but in your opinion (or anyone who could ring in on this) what would you consider the highest core temps you would feel safe for a 24/7 overclock (assuming stable)?
Currently I'm @ 4.3 GHz. I haven't run any overnight tests yet, but after 10 minute small FFT torture tests, my hottest single core temp maxed at 77 at some point, but running average of all six is 72.

And when running Prime95 torture test, which is it best to run? Small FFTs (ram not tested much), In-place large FFTs (max heat, some ram tested), or Blend (lots of ram tested)?

Hi 00011011
980X I tried two, we needed first 4.3G Vcore1.65V:shakes:
I tested the CPU and heat test operator prim95 I think highly reliable utility.
1core will not even when I make an error. And one 12-hour loop
Required.;)


Now get it crunching! :cord:

No but really amazing job! :up: I think a 480 rad will be pushing it alittle eh?

P.S. get it crunching ;) that thing would be a beast at wcg :yepp:

Thanks Gonzalo-Gonads
Large individual differences in the CPU! It is too many bad yield Bath #


HI

Amazing project dude.

Can u just tell me , is that a conector witch are in the midle of the 1 gt295 and the second, or is a junction of males and females conector?
if its a conector can u just give me the exact name?

I love it,, the look man..

Congratzz :up:

Hello The.Sorrow:)
Bitospawer GT295 combines the connection of the joint:up:
103773
http://www.performance-pcs.com/catalog/index.php?main_page=product_info&cPath=59_346_393_621&products_id=24677
http://www.performance-pcs.com/catalog/index.php?main_page=product_info&cPath=59_346_393_622&products_id=23697



and may you tell me will it be possible to put two 3x120 rads on bottom with16cm psu?

Hello rioja:)
What unit two loops? Not that my 120x3
One of the right panel, the second left panel, attach the three intermediate panel.
However, air flow is difficult.:confused:
the top exhaust:yepp:


Love this project, totally inspiring to me! Question, would a 140.3 fit inside the case across the top? I'm debating a single loop w/a 140.3 and a 120.1 for an i7 920 and 2x GF100's.

Hello mlee49
Thanks to word of praise!:)
It is a difficult debate! I see skinnee test.
XSPC rad I like the pitch. Slow (800-1000rpm) of the cooling fan is working I prefer quiet.
For the GTX480, HWLabs SR1-480, XSPC-RX480 candidates cited a quietly cool for me to determine the size needed GTX 480 has a narrow pitch fan speed 1800rpm ↑　SR-1 is a low volume.We have to xspc480.I think I prefer a quiet 140.3.:rolleyes:


mlee49: I've seen few worklogs with 140.3 on top. Sorry, i'm too lazy to seerch urls for them. Main thing you should watch for if 140.3 rad's width fits between 5.25 enclosure bays walls. Some 140rads fits (don't remember, XSPC or TFC or something else), some (in particular wider Black Ice GTX/SR1 - do not = requiered some cutting of top of those 5.25 walls). And of course you need cut top for larger rad and paint cuts or slap some nice rad grill ontop.


have this case and think about it right now so theres 1cm gap only (with RX360 and OCZ PSU)and in this place bunch of wires ATX24 connector. If you can mod your psu - (turn this bunch on 90degrees) I think it possible.

noeru you have this PSU what do you think is it possible put here RX360?

http://www.overclock3d.net/gfx/articles/2009/09/07155701257l.jpg
http://www.overclock3d.net/gfx/articles/2009/09/07155703682l.jpg


also for two rads at bottom you'll need this side panel
https://shop.corsair.com/store/item_view.aspx?id=1171683

Hello Nage
I tried to put a 360 in the first study.
But I abandoned the ocz-z-z1000PSU
360 if possible get things set up next to the wiring is possible.
But now my system is 1000W but I have trouble in getting enough.
It will create a new side panels and me.


Nice build and photo's. But I think the one color light would look better.

Hello Awers
Thank you　Yes! Certainly:D


Hi Noeru! The length and width of your 480 cut out?? I have the same rad aswell, xspc 480. Was hoping to get a head start on the cuts before my bitspower grill arrives :)


You could do that, and it may even be easier to use one of the new antec psu that are 120mm high, and place the fan their. It would greatly simplify cooling.
Although, I dont think they go up 1000w, but you may not actually need 1000w.

Another idea, is to use one or two rx360 instead. I think you have 572mm on the base to play with. The rx360 is 410mm, so that leaves 172mm to play with. It would still force you to get creative with psu mounting. You could either get a short psu and get very very creative, or fab a psu extender.
Or you could fab up a new psu case to work with that small ammount of space, just depends how comfortable you are with cracking open your psu.

Either way you have your work cut out for you. It's funny, no matter how big a case gets, you always can think of ways of where you just wish it was just a bit bigger.




Amazing build. btw


Take some pix of your dachsund! He's so damn cute.
Thanks ScottALot　She is so very cute:p:

[Omarko]

amazing build ... I picked up few things and replicating it in my current project LINK (http://forums.overclockers.com.au/showthread.php?t=866639)

I'm struggling to fit the XSPC Dual bay res in the 5.25" as the sliders are sticking too much and prevent me from putting it in. I might have to dremel them off.

[noeru]

amazing build ... I picked up few things and replicating it in my current project LINK (http://forums.overclockers.com.au/showthread.php?t=866639)

I'm struggling to fit the XSPC Dual bay res in the 5.25" as the sliders are sticking too much and prevent me from putting it in. I might have to dremel them off.

Great job!
XSPC Dual Bay has resonance.
DDC3.25 I think it is best to fix a pump panel;)

[00011011]

Obviously the lower the better, but in your opinion (or can anyone else answer this?) what would you consider the highest core temps you would feel safe for a 24/7 overclock (assuming stable)?

Currently I'm @ 4.3 GHz. I haven't run any overnight tests yet, but after 10 minute small FFT torture tests, my hottest single core temp maxed at 77 at some point, but running average of all six is 72.


I appreciate your response noeru, but you didn't answer my question; perhaps you didn't understand me. Hopefully this Google translation works properly :)

明らかに良い、低いがあなたの意見（または他の誰これを答えることができる？）どのようなあなたが安全な2 4 / 7オーバークロック（安定仮定を感じると、最高のコアタンを検討する）？

現在、私は@ 4.3 GHzのです。私はまだすべての夜間テストを実行していない10分小さなFFTの後、私の一番ホットなシン グルコアの温度を77でいくつかの点で大変疲れてテストを拷問が、平均全6を実行して72です 。

[noeru]

I appreciate your response noeru, but you didn't answer my question; perhaps you didn't understand me. Hopefully this Google translation works properly :)

明らかに良い、低いがあなたの意見（または他の誰これを答えることができる？）どのようなあなたが安全な2 4 / 7オーバークロック（安定仮定を感じると、最高のコアタンを検討する）？

現在、私は@ 4.3 GHzのです。私はまだすべての夜間テストを実行していない10分小さなFFTの後、私の一番ホットなシン グルコアの温度を77でいくつかの点で大変疲れてテストを拷問が、平均全6を実行して72です 。

00011011
sorry　Google's translation :p:
Overclocking 24 / 7　try Prim95 4.5G 12hr 1roop roomtemp is 22.5
maxcore temp core1 69 core2 71 core3 63 core4 66 core5 69 core6 68
C1E off HT on 144.7x31 Vcore1.400v QPIVTT 1.350v NB 1.42 DRAM 1.63+

103922
I tried 4 Gulftown results
Gulftown is very large individual differences.
4.3G but passes Vcore1.65v batch # There were no:shrug:
http://noeru-dairu.jugem.jp/?page=1

[noeru]

next VGA is :rolleyes:

103923

[noeru]

I get worried about the next VGA:confused:
GTX480 2GPS　VS　HD5970 4GPU

[ScottALot]

Definitely the 5970s.

[Saltire]

Definitely the 5970s.

+1 :up:

[noeru]

Definitely the 5970s.


+1 :up:

ScottALot、Saltire　　Thank you
GTX480 is 438w:eek: HD5970 is 399w:clap: GTX295 is 418w (http://noeru-dairu.jugem.jp/)
SLI and CF really does make a difference seems

[ScottALot]

I wonder if you can get these: http://www.newegg.com/Product/Product.aspx?Item=N82E16814150460&cm_re=XFX_5970-_-14-150-460-_-Product

[y0gi]

Cant believe this one slipped by me for so long. I just spent the last hour reviewing this thread. Absolutely awesome. Good work, noeru.:up:

[taters mcgee]

Is it just me, or is the nickel coming off of the Mips Ramfreezer in post 211? :eek:

[Danger30Q]

Can somebody please tell me what this tool is?

http://www.xtremesystems.org/forums/attachment.php?attachmentid=98781&stc=1&d=1258769951

I'm about to drill out the front rivets but didn't see this additional tool that's needed inside the bay.

[Philwong]

Can somebody please tell me what this tool is?

http://www.xtremesystems.org/forums/attachment.php?attachmentid=98781&stc=1&d=1258769951

I'm about to drill out the front rivets but didn't see this additional tool that's needed inside the bay.

That's a Black & Decker RTX flexi shaft.

http://www.blackanddecker.com/ProductGuide/Product-Details.aspx?ProductID=2709

Phil

[Danger30Q]

Thank you much Phil!

Great work so far Noeru. Your build is the inspiration for my future 800D build which will look very similar to yours except I have only (1) 240 radiator on the bottom and (1) 360 radiator hanging off the back of the case.

[noeru]

Thank you much Phil!

Great work so far Noeru. Your build is the inspiration for my future 800D build which will look very similar to yours except I have only (1) 240 radiator on the bottom and (1) 360 radiator hanging off the back of the case.

104175

Hello Danger30Q
It is as you say Philwong:)

hello and thanks　Philwong　:up:

104177

[noeru]

GTX480 vote has been also extended
Which do GTX480SLI vs 5970CFX Haisukoa?
I want to order 480 or 5970 Waterblock soon:(
The performance-pcs

[Danger30Q]

Thank you for those additional pics noeru.

[noeru]

thanks All. I will try to hd5970. i like 4GPU:p:

104376

104377

104378

[V0id]

Beautiful graphics cards and beautiful project! :up:

[noeru]

Beautiful graphics cards and beautiful project! :up:

hello V0id :) very tanks!
I choose two cards from this 5970:up:

104414


104415


104416


104417

[ScottALot]

What's the BLACK EDITION for? (You can't have all three running in the same rig!)

[noeru]

What's the BLACK EDITION for? (You can't have all three running in the same rig!)

hello ScottALot:)

Yes, can not be 6GPU
I know the difference between them is VGA:)
I select two pieces from here

[ScottALot]

And I get the third one, right?

[erikmorgan]

Very nice build! :up:

[noeru]

And I get the third one, right?
The VGA is Air cooled in this Sapp5970> Sapp5970OC> XFX5970
All 1125mV 800/1203

104472

3DMark06 and Vantage score is.:shrug:


Very nice build! :up:
hi erikmorgan very thank :)

[noeru]

Summer soon:rolleyes:

104473

[ScottALot]

And I get the third one, right?

No. I mean, you're going to give me the 5970 that you don't use haha :D

[noeru]

EK-FC5970 - AMD/ATI Radeon HD 5970 Series Reference Design - Nickel

104569

104570

104571

[noeru]

104575

104576

[manu_D]

Hello Noeru,

With so much power you swore to blow up the rivets of the Obsidian. I have not yet seen an Obsidian climbing on trees, but I believe that on your worklog it is only a question of patience.
I am going to really enjoy the show two 5970 in this case.
Small caress to Airu. I understand that she wants to lower the head! I am a little bit like that also!

[noeru]

Hello Noeru,

With so much power you swore to blow up the rivets of the Obsidian. I have not yet seen an Obsidian climbing on trees, but I believe that on your worklog it is only a question of patience.
I am going to really enjoy the show two 5970 in this case.
Small caress to Airu. I understand that she wants to lower the head! I am a little bit like that also!

Hello manu_D
Thanks, we look forward to your project.:up:
The Kanihendakkusu is Airu:)

[noeru]

EK-FC5970-Nickel+Blood+



104638

104639

[Red-5]

Great looking project. :up: Looking forward to seeing it completed with all your new gear installed. :yepp:
That 5970 Gpu block looks great with the blood red coolant. :)

[noeru]

Great looking project. :up: Looking forward to seeing it completed with all your new gear installed. :yepp:
That 5970 Gpu block looks great with the blood red coolant. :)

hi Red-5 Thanks:)

more pic:)


104667


104668


104669


104670


104671

[aka_GK]

wow, that's a huge GPU power :up: :up:
nice blocks too

[shazza]

:up: Looking good!

[luke997]

Great project, these blocks with red coolant look really hot :D

[manu_D]

Hi Noeru,

EK waterblocks 5970 is really beautiful mechanical parts. With the red liquid cooling the look is magic!

The internal volume of the Obsidian is planned for mother boards in the eATX size, it is thus spacious. The volume needs to be occupied by big GPU cards, so that the case is emphasized.
We say about a car that it is beautiful, when besides the body it also has a beautiful engine (a powerful engine). So when the internal volume of Obsidian (the body) is occupied by big cards, and when they are powerful (the engine), we cannot make better! Aesthetics and power are combined.

What I find it's a pity, it is only in the position ATX inverted that we see waterblocks upward. In the position ATX the aesthetic charm is hidden in a way. It's HARD!

I have already seen in France dogs of the race of Hairu. Thus I knew it was a race, but I did not know the name. "CROUCH, CROUCH" to miss Hairu, sweet little face.

[Liderc]

Beautiful blocks.

[noeru]

wow, that's a huge GPU power :up: :up:
nice blocks too


:up: Looking good!


Great project, these blocks with red coolant look really hot :D


Hi Noeru,

EK waterblocks 5970 is really beautiful mechanical parts. With the red liquid cooling the look is magic!

The internal volume of the Obsidian is planned for mother boards in the eATX size, it is thus spacious. The volume needs to be occupied by big GPU cards, so that the case is emphasized.
We say about a car that it is beautiful, when besides the body it also has a beautiful engine (a powerful engine). So when the internal volume of Obsidian (the body) is occupied by big cards, and when they are powerful (the engine), we cannot make better! Aesthetics and power are combined.

What I find it's a pity, it is only in the position ATX inverted that we see waterblocks upward. In the position ATX the aesthetic charm is hidden in a way. It's HARD!

I have already seen in France dogs of the race of Hairu. Thus I knew it was a race, but I did not know the name. "CROUCH, CROUCH" to miss Hairu, sweet little face.


Beautiful blocks.

I am very happy thank you All:)

104885

104886




Hi manu_D
The work is very difficult:(. But consider the alternative;)

[noeru]

EK-FC5970 RAM Backplate - Nickel-Plate

104881

EK-FC5970 - AMD/ATI Radeon HD 5970 Series Reference Design - Nickel

104884



Stop Work;)　I'm noeru

104882

[Wezly]

That's adorable.

[CCC]

hilarious how big that 5970 is , even makes a dog look small.. lol