Help Me To Go more Higher

[Thenura]

Hi guyz im now at 3.82 :S Intel Burn Test stable 1 hr

CPU vcore - 1.36
DIMM V - 1.935
NB v - 1.375
CPU VTT - 1.35

My Ram is at 5.5.5.18 851 mhz :D
FSB is 425

cant go 430 :S Intel Burn test 98% percent passed only :S

Help mee

[YukonTrooper]

Increase your voltages and raise your multiplier just to see if your chip will even go higher. You might be hitting an FSB wall, or there might be an FSB hole in that range on the Foxconn Mars (not familiar with this board).

[HDCHOPPER]

havent found any holes in the mars yet myself ... but that might be all your cpu has at that volt :shrug:

up the volts on your cpu and see if it goes any further and 800 ram will normally got to 1000 ( most will) mine will hit 1200 at 2.1 volts :D

maybe more vtt also maybe less mine uses 2.0 v for 4.0 cpu speed and over :D

[Thenura]

havent found any holes in the mars yet myself ... but that might be all your cpu has at that volt :shrug:

up the volts on your cpu and see if it goes any further and 800 ram will normally got to 1000 ( most will) mine will hit 1200 at 2.1 volts :D

maybe more vtt also maybe less mine uses 2.0 v for 4.0 cpu speed and over :D

giving over 1.35 willl damage 45nm cpus ?>

[YukonTrooper]

You can put extra volts into the chip just to see if it's capable of higher speeds. You don't want to keep it at high levels, though.

[HDCHOPPER]

Thunera upwards of 1.4 + is what eye hear about that

and ya what Trooper says never good to keep em maxed out best just left to benching

actullay my cpu doesnt like anything over 1.2 vtt with that have gotten to 4.7 but need better ram to get to 5.0 cpu will do it tho :D

[Thenura]

Thunera upwards of 1.4 + is what eye hear about that

and ya what Trooper says never good to keep em maxed out best just left to benching

actullay my cpu doesnt like anything over 1.2 vtt with that have gotten to 4.7 but need better ram to get to 5.0 cpu will do it tho :D

hey very badly i got a C0 one ,whats ur stepping .? and whats the soft u use to check the stability ,and im now stable at 3.82 with 1.37 v :S

[Thenura]

1.4 - 3.89 not stable with NB - 1.375 and CPU VTT - 1.35 ,,,WTF

[Thenura]

and after 1.42 all voltages are RED .so im a bit afraid :P ,:S

is their any spots to go 4 ghz with less volts

[HDCHOPPER]

hey very badly i got a C0 one ,whats ur stepping .? and whats the soft u use to check the stability ,and im now stable at 3.82 with 1.37 v :S


co also and eye use ibt normally eye run nb at 1.5~1.7 volts depending on what speed and how many ram sticks are in

[Thenura]

co also and eye use ibt normally eye run nb at 1.5~1.7 volts depending on what speed and how many ram sticks are in

i have 2 ram sticks and my NB is 1.35 should i go more ? i need 4 ghz and i need a profile for bench ,for that is it possible to give more voltage to cpu ?1.45 ?

[Thenura]

http://processorfinder.intel.com/Details.aspx?sSpec=SLAPL

Intel Says keep it under 1.3625 :S

[HDCHOPPER]

ya have read that check the intel section thiers an e8400 , 8500 , 8600 thread thier may help you out plenty and so far 1.4 is safe cpu as long as you keep it cool

my n/b is allways at least 1.5 v for 4.0 or better cpu speed

my bios settings are

445 fsbX9cpu multi = 4.o
1:2.4 mem divider =1069 iirc
100 pci express

X1.00 cpu volt multi
1.3375 cpu volts
2.205 dram volts for 4 sticks & 2.10 volt for 2 sticks
1.5 nb volts
1.2 vtt volts
1.5 sb / pll volts


good luck ;)

[Thenura]

@HDCHOPPER

Hy mate im now at 3.69 Ghz with 1.30v STABLE ! i wonder it needs 1.41v to go 3.9Ghz //WTF is this :/
and abt ur configurations .im a bit afraid to apply those coz u r connected ur A/C to the mobo :P :D

[HDCHOPPER]

hahahahaah thiers no ac in the winter time :D which is now

my temp differance between just amb air and ac is only about 3*~5* c

but my coolit does keep it nice & cool like right now it 14*c :D

but even with my thermaltake I1 with a silverstone 120cfm fan on it these settings