Gigabyte EP45-DS3R large VDROP?

[hawk999]

is somebody encounter this problem like mine?? because when i try to reach 3.6ghz on my e7200 i will nid to go 1.45v just to stable it and below 1.45v it will post but it will frost when i go on to windows..

please help me guys :(:confused:

[enteon]

did you try raising other voltages a bit? like pll, fsb, nb, whatever.
at least 45nm quads won't go high without raising the other voltages a lot.
or has that changed with the p45 series?

maybe just bad luck :shrug:

[hawk999]

maybe i just a noob??hehehe

please help me guys

[enteon]

raise all voltages you see by 0,1V and try again :D

but maybe you shouldn't raise PEG voltage ^^

[hawk999]

GIGABYTE GA-EP45-DS3R
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:Turbo
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3600Mhz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:400Mhz
PCI Express Frequency (Mhz) .........:100mhz
C.I.A. 2
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive.................: 700mv
CPU Clock Skew (ps)....................: 150ps
MCH Clock Skew (ps)...................: 250ps
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: [Disabled]
(G)MCH Frequency Latch...............: [333]
System Memory Multiplier ..............: 2.00b
Memory Frequency (Mhz) ..............: 800Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................: 4
tRCD .........................................: 4
tRP'...........................................: 4
tRAS..........................................: 12
Advanced Timing Control [Press Enter]
tRRD...........................................: 3
tWTR..........................................: 3
tWR............................................: 6
tRFC...........................................: 52
tRTP...........................................: 3
Command Rate (CMD) ....................: Auto
Channel A
Static tRead Value.........................:Auto
tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Channel B
Static tRead Value.........................:Auto
tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:12
Twr2rd(Different Rank)...................:6
Trd2wr(Same/Diff Rank)..................:15
{U]Motherboard Voltage Control{/U]
Voltage Type.………... Normal
CPU
CPU Vcore….……….........................:1.39v
CPU Termination…..... 1.200V*.......: 1.240v
CPU PLL…………………....1.500V*.......: 1.57v
CPU Reference1 ……....0.760V*.......: Auto
CPU Reference2………,,0.800V*.......: "Not Available"
MCH/ICH
MCH Core…………….....1.100V...........: 1.36v
MCH Reference….…….0.760V...........; .760
MCH/DRAM Ref.…......0.900V...........:0.900
ICH I/O……………….....1.500V............: 1.500v
ICH Core…………...……1.100V............: "Not Available"
DRAM
DRAM Voltage ……....1.800V............: 2.10v
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU

this are my settings in bios but 3.6ghz will freeze in windows :(

[hawk999]

guys?? is somebody still here?

[hawk999]

anyone ?guys?

[SNiiPE_DoGG]

{U]Motherboard Voltage Control{/U]
Voltage Type.………... Normal


set this to enable^^^

[hema]

load line calib.
in bios if found

[hawk999]

load calib? i didn't find that in my bios :(