Please check this before I order:

[Jamestuk]

Gonna order in a little bit, please tell me if I missed anything. Went with 10/8 compression because I don't have much space and gonna need some very tight bends. Many Thanks :)

EK-FC3870 CF - Nickel-plated
- Barb Size 10/8mm Compression

XSPC Bay Reservoir - Clear Acrylic
- Barb Size 10/8mm Compression

12V Laing DDC-1T Plus Ultra w/Alphacool Top
- Accessories Laing Damper Kit (Set of 4)
- Barb Size 10/8mm Compression

EK-Supreme CPU - Plexi EK-Supreme CPU - Plexi
- Barb Size 10/8mm Compression

Swiftech MCR220-QP Dual 120mm Radiator
-Alphacool 8mm Angled Screw Connector

XSPC RS120 Black
- Barb Size 10/8mm Compression

Alphacool 8mm Polyurethane Tubing (Transparent) - 2m

2x Arctic Ceramique Thermal Compound (2.5g) (will this be enough?)

LGA 775 Motherboard Back Plate

Feser One Cooling Fluid - UV PURPLE

4x Xilence Red LED

[disruptfam]

looks good to me....I would change the tim to mx2 though

Make sure you have barbs for all your blocks/pumps/res

I can't comment on those fans chosen never heard of them before.

I would also consider doubling up pumps if this is a 1 loop system

[Jamestuk]

mx2 it is then. how many tubes of it am I gonna need? one enough or two?

hmm can't really afford two pumps at the moment... I'll buy another later if it turns out to be a problem!

[disruptfam]

I'm assuming you talking in metres

I would go 3m just to be safe...

Better having abit extra then not having enough

[Jamestuk]

tubes of mx2 i meant lol sorry.

T-line maybe as well?

[disruptfam]

1 will be enough.Comes in a very large tube.

If you don't want the res t-line if you like

[Jamestuk]

hmmm res is probably fine!

ordering time! eeep!

thankyou for your help and guidance, it is much appreciated!

[disruptfam]

no worries :)

[Xerran]

looks good to me....I would change the tim to mx2 though

Make sure you have barbs for all your blocks/pumps/res

I can't comment on those fans chosen never heard of them before.

I would also consider doubling up pumps if this is a 1 loop system


+1 for Arctic Cooling MX-2 :up:

I'm using Fesser-One also, Acid green :up:

Good luck on your order and setup, I just finished my first ever liquid cooling setup (http://www.xtremesystems.org/forums/showthread.php?p=2830720&posted=1#post2830720) this morning and I'm loving it so far. :welcome:

[Pedalmonkey]

carefull running the EK Supreme in that loop. granted its not very restrictive, you might get better temps with a D-Tek Fuzion.

[disruptfam]

ek supreme is very restrictive...

[Pedalmonkey]

well restrictive loop is what i meant. :p, still gets a pretty high flow rate in Martins chart. but the D-Tek will increase flow and drop the temps of the entire loop

[lior307]

Is the EK is better than the Fuzion for CPU ??

[iadstudio]

I'd get the XSPC DDC top instead of Alphacool. It has better performance.

[InfamousChu]

I'd get the XSPC DDC top instead of Alphacool. It has better performance.

+.. alphacool top was the worst in martins test XSPC Res top won.. but the regular XSPC also did very well

[Jamestuk]

I'm using Fesser-One also, Acid green :up:


I hope the purple is a nice colour...hard to tell from the picture. Not got a case window though anyhow, so doesn't matter too much. Could get some acryllic from work and mod one in I guess. Will have to see what it looks like inside case with watercooling.


I'd get the XSPC DDC top instead of Alphacool. It has better performance.

ah well too late to change it now anyway. I went with the alphacool due to its anti vibration bay mounting screws, in the hope it would be quieter. I doubt it would be massively better anyhow, however I must admit I haven't read the review so I don't know :)