Quad Core OC Database [Archive] - XtremeSystems Forums

View Full Version : Quad Core OC Database

Pages : [1] 2

CraptacularOne

09-04-2007, 07:29 AM

OK I would like to start a Quad Core Database so we can all post and see what steppings are doing what. All quads are welcome and I will have individual categories for each model. So post up and lets do something useful :)

So here's the deal, give me....
1) Post your CPU model & Core revision (B3 or G0)
2) Week (L726A...ect)
3) CPU-Z Validation
4) Screen shot of it running at that speed (orthos, prime95..ect) 100% load
5) Cooling being used
6) Voltage
7) Motherboard used (this is optional but helpful just the same:))

I will accept a quad Pi 32m run (4 instances of 32m Pi) as well but please stable OCs only, I will keep the thread up to date. So lets see what you guys got :)

CraptacularOne

09-04-2007, 07:29 AM

***Key***
PC = Phase Change
WC = Water Cooled
AC = Air Cooled
P = Prime stable
32m = Pi 32m stable
Wp = Wprime stable

OC Table---------------------------------

QX9650 Table

QX9650 C0 - L739A640 - 4Ghz P stable - WC - 1.34v - ASUS Maximus Formula SE - by -------- Iceflight

QX6850 Table-----------------------------------

QX6850 G0 - L723A658 - 3.6Ghz P stable - AC TR Ultra 120 - 1.36v - ASUS Blitz Formula - by ---------Cordovader
QX6850 G0 - L723A658 - 3.6Ghz P stable - D-Tek Fuzion WC- 1.36v - DFI LP P35 TR - by -------------pumbertot

QX6700 Table----------------------------

QX6700 B3 - L638A*** - 3.8Ghz (13x293) P stable - WC Apogee GT - 1.52v - EVGA 680i - by ----CraptacularOne
QX6700 B3 - L639A615 - 3.52Ghz P stable - WC Apogee GT - 1.41v - ASUS P5WDH - by ---------------Luis_GT

Q6700 Table-----------------------------
Q6700 G0 - L713A358(ES) - 4Ghz (445x9) P stable - PC (custom) - 1.52v - Abit IP35 PRO - by ---------doom_st

Q6600 Table-----------------------------

Q6600 G0 - L727A856 - 4.36Ghz P stable - PC (custom) - 1.7v - Asus P5K-E - by -------------------jinu117
Q6600 G0 - L745A817 - 4.1Ghz P stable - WC EK Supreme - 1.58v - ASUS Blitz Ext - by --------------- Ic3man
Q6600 G0 - L737B186 - 4.01Ghz - WC (custom) - 1.504v - ASUS P5K Prem - by --------------------Devious
Q6600 G0 - L743A866 - 4.05Ghz WC D-Tek Fuzion - 1.52v - Gigabyte P35 DS4 - by ------------ road-runner
Q6600 G0 - L727A934 - 4Ghz P stable - PC Vapo LS - 1.425v - ASUS P5K Prem - by ----------------dragonhunter
Q6600 G0 - L723A795 - 4Ghz P stable - PC jinu117 - 1.485v - ASUS P5K Prem - by -----------------billdavis
Q6600 G0 - L737B064 - 4Ghz P stable - WC D-Tek Fuzion - 1.488v - Gigabyte X38 DQ6 - by ------ rbsmontemor
Q6600 G0 - L724A629 - 4Ghz P stable - WC D-Tek Fuzion - 1.6v - EVGA 680i - by ------------------turtletrax
Q6600 G0 - L724A784 - 4Ghz P stable - WC D-Tek Fuzion - 1.62v - ASUS P5K Prem - by ------------TinTin
Q6600 G0 - L723B010 - 4Ghz (500x8) P stable - WC D-Tek fuzion - 1.64v - ASUS Blitz Formula - by---Ic3man
Q6600 G0 - L727A918 - 3.93Ghz P stable - AC - 1.65v - EVGA 680i - by -------------- St3vil_68
Q6600 G0 - L737B264 - 3.915Ghz P stable - WC Apogee GT - 1.416v - ASUS Maximus Form - by ----- Zucker2k
Q6600 G0 - L34B164 3.9Ghz P stable - AT TR Ultra 120 E - 1.472v - Gigabyte P35 DS4 - by ---------- road-runner
Q6600 G0 - L725B057 - 3.9Ghz P stable - WC D-Tek Fuzion - 1.496V - ASUS P5K-E - by ------------dj883u2
Q6600 G0 - L723B284 - 3.9Ghz P stable - WC Apogee GT - 1.52v- DFI P35-T2R - by - --------------RLM
Q6600 G0 - L741A*** - 3.9Ghz P stable - AC TR Ultra 120 E - 1.528v - EVGA 680i - by ----------- Cloud.gm
Q6600 G0 - L726A840 - 3.9Ghz P stable - WC Apogee GT - 1.5375v - EVGA 680i - by -------CraptacularOne
Q6600 G0 - L726A822 - 3.9Ghz P stable - WC D-Tek Fuzion - 1.58v - ASUS P5K Dlx - by ------------rbsmontemor
Q6600 G0 - L737B064 - 3.8ghz (475x8) P stable - WC - D-Tek Fuzion - 1.392v - ASUS P5K Dlx - by - rbsmontemor
Q6600 G0 - L727B159 - 3.85Ghz P stable - AT TR Ultra 120 E - 1.536v - Gigabyte P35 DS4 - by ------ miahallen
Q6600 G0 - L726A951 - 3.85Ghz P stable - WC D-Tek Fuzion - 1.52v - ASUS P5K Dlx - by -----------no_n|ck
Q6600 G0 - L726A850 - 3.85Ghz P stable - AC TR Ultra 120 - 1.537v - ASUS P5K Dlx - by ----------crossg.
Q6600 G0 - L737B242 - 3.825Ghz P stable - AC TR Ultra 120 E - 1.376v - ASUS Maximus Form - by - mc2k
Q6600 G0 - L737B*** - 3.825Ghz P stable - WC D-Tek Fuzion - 1.5v - Gigabyte X38 DQ6 - by ----- pvtdonuts
Q6600 G0 - L727A918 - 3.82Ghz P stable - WC Apogee GT - 1.52v - ASUS Striker Extreme - by -----linflas
Q6600 G0 - L724A*** - 3.82Ghz P stable - WC D-Tek Fuzion - 1.54v - ASUS Striker Extreme - by----nugzo
Q6600 G0 - L723A674 - 3.81Ghz P stable - WC Apogee GT- 1.54v Gigabyte DS4 - by ----------------aspms*
Q6600 G0 - L731B163 - 3.8Ghz P stable - AC Tuniq Tower - 1.525v - Maximus Formula SE - by ------loc.o
Q6600 G0 - L726A*** - 3.8Ghz P stable - WC - 1.43v - ASUS P5K Dlx - by -------------------------njkid32
Q6600 G0 - L727A673 - 3.8Ghz P stable - AC TR Ultra - 1.472v - Gigabtye P35-DQ6 - by ------------dertimaushh
Q6600 G0 - L720B066 - 3.8Ghz P stable - AC TR 120 - 1.5v - Abit IP35 Pro - by --------------------Ace-a-Rue
Q6600 G0 - L726A849 - 3.8Ghz P stable - AC TR Ultra 120 - 1.5v ASUS P5K E - by ------------------sam95ta
Q6600 G0 - L724A*** - 3.8Ghz P stable - WC Apogee GT - 1.55v - DFI P35-T2R - by ---------------RLM
Q6600 G0 - L719B278 - 3.8Ghz P stable - WC D-Tek Fuzion - 1.6v - Abit IP35-Pro - by - ------------vkostas
Q6600 G0 - L720B023 - 3.76Ghz P stable - WC Apogee GT - 1.475v - ASUS P5K Prem - by -----------cfree1012
Q6600 G0 - L720B066 - 3.73Ghz P stable - WC ApogeeGTX - 1.44v - ASUS P5K Dlx - by -------------NaeKuh
Q6600 G0 - L726A951 - 3.71Ghz P stable - AC TR Ultra 120 - 1.425v - ASUS Striker Extreme - by ----cliffy
Q6600 G0 - L723A963 - 3.7Ghz P stable - WC - 1.43v - ASUS P5K Dlx - by -------------------------njkid32
Q6600 G0 - L719B272 - 3.7Ghz P stable - WC Storm G4 - 1.44v - Gigabyte P35 DS4 - by ----Xiphias-Gladius
Q6600 G0 - L726A601 - 3.7Ghz P stable - *cooling not listed* - 1.45v - *mobo not listed* - by ------sergmann
Q6600 G0 - L727A934 - 3.7Ghz P stable - WC D-Tek Fuzion - 1.475v - ASUS P5B Dlx - by ------------drynyks
Q6600 G0 - L723A917 - 3.7Ghz P stable - WC Storm G4 - 1.48v - ASUS P5K Prem - by ---------------Fosco
Q6600 G0 - L724A760 - 3.7Ghz (462x8) P stable - WC D-Tek Fuzion - 1.49v - EVGA 680i - by --------nugzo
Q6600 G0 - L724A900 - 3.7Ghz P stable - AC TR Ultra 120 - 1.5v - ASUS P5K Dlx - by ---------------sobol
Q6600 G0 - L737B574 - 3.6Ghz P stable - AC TR Ultra 120 E - 1.3v - Abit X38 QuadGT - by ---------- Hazzan
Q6600 G0 - L737B063 - 3.6Ghz P stable - AC TR Ultra 120 E - 1.304v - ASUS P5K Dlx - by --------- ineedaname
Q6600 G0 - L740A740 - 3.6Ghz P Stable - WC - 1.328v - Gigabyte P35 DS3P - by------------------okorn
Q6600 G0 - L730B292 - 3.6Ghz P stable - WC D-Tek Fuzion - 1.375v - Asus P5k Deluxe - by ---------Supershanks
Q6600 G0 - L719B*** - 3.6Ghz P stable - AC TR Ultra-120 - 1.385v - ASUS P5K Dlx - by ------------rbsmontemor
Q6600 G0 - L719B271 - 3.6Ghz P stable - AC Tuniq Tower - 1.39v - Gigabyte P35 DQ6 - by ----------3NZ0
Q6600 G0 - L726A854 - 3.6GHz P stable - WC D-Tek Fuzion - 1.392v - ASUS P5K Dlx - by ---------- xenolith
Q6600 G0 - L724A786 - 3.6Ghz P stable - WC D-Tek Fuzion - 1.396v - abit IP35 Pro - by ------------largon
Q6600 G0 - L726A951 - 3.6Ghz P stable - AC TR Ultra-120 - 1.4v - ASUS P5K Dlx - by ---------------mc2k
Q6600 G0 - L728A*** - 3.6Ghz P stable - WC D-Tek Fuzion - 1.4v - ASUS P5K Dlx - by -------------=Pseudo=
Q6600 G0 - L727A829 - 3.6Ghz P stable - AC (not listed) - 1.4v - ASUS P5K-E - by -----------------Xevipiu
Q6600 G0 - L726A840 - 3.6Ghz P stable - WC - 1.41v - ASUS P5K Dlx - by --------------------------njkid32
Q6600 G0 - L726A850 - 3.6Ghz P stable - AC TR Ultra 120 - 1.41v - ASUS P5K Dlx - by --------------crossg
Q6600 G0 - L720B080 - 3.6Ghz P stable - AC TR Ultra 120 - 1.4125v - EVGA 690i - by ---------------CikaNovo
Q6600 G0 - L723A825 - 3.6Ghz P stable - AC TR Ultra 120 - 1.42v - Gigabyte DS3-R - by -----------[XC] 4X4N
Q6600 G0 - L723A930 - 3.6Ghz P stable - WC D-Tek Fuzion - 1.432v - ASUS P5K-E - by ------------ leo_bsb
Q6600 G0 - L724A760 - 3.6Ghz (450x8) P stable - AC TR 120 Ultra E - 1.45v - DFI LP P35 T2R - by - GripS
Q6600 G0 - L723A977 - 3.6Ghz P stable - AC TR Ultra 120 E - 1.45v - ASUS P5K Dlx - by --------- Viper.Br
Q6600 G0 - L727A963 - 3.6Ghz P stable - AC TR Ultra 120 - 1.4625v - ASUS P5K-E - by -------------ThePrutser
Q6600 G0 - L725B020 - 3.6Ghz (450x8) P stable - WC Apogee GT - 1.465v - ASUS P5K Dlx - by -----WiTcHkInG
Q6600 G0 - L723A963 - 3.6Ghz P stable - AC Tuniq Tower - 1.475v - ASUS P5K Prem - by -----------ocZZZ
Q6600 G0 - L734A*** - 3.6Ghz P stable - WC Swiftech Apogee - 1.475v - Asus P5K-E - by ----------Evil
Q6600 B3 - **(ES)** - 3.6Ghz P stable - AC TR Ultra 120 - 1.475v ASUS P5K Dlx - by ---------------BND|MOD
Q6600 G0 - L734A621 - 3.6Ghz P stable - TR Ultra 120 - 1.5v - ASUS P5E - by ----------------------nonvtec
Q6600 G0 - L727B159 - 3.6Ghz P stable - AC Zalman 9500 - 1.5v - Gigabyte GA-P35-DS4 - by -------miahallen
Q6600 G0 - L730B304 - 3.6Ghz P stable - AC Xigmatek HDT - 1.52v - MSI P35 Neo2 - by ------------Nazu
Q6600 G0 - L721A814 - 3.6Ghz (450x8) P stable - WC Apogee GT - 1.54v - ASUS P5K Dlx - By ---------badboy
Q6600 G0 - L723A978 - 3.6Ghz P stable - AC TR Ultra 120 - 1.575 - P35-DS3R - by -----------Ch0p5t1ckB01
Q6600 G0 - L727A658 - 3.55Ghz P stable - AC Cooler Master Gemini II - 1.56v - Abit IP35-E - by - dragonhunter
Q6600 G0 - L720B062 - 3.51Ghz P stable - AC TR Ultra 120 - 1.45v - Gigabyte P965 - by ------------vocch
Q6600 G0 - L724A760 - 3.51Ghz P stable - AC Scythe Infinity - 1.48v - DFI P965S - by ------------GripS
Q6600 B3 - L722A471 - 3.51Ghz P stable - WC D-Tek Fuzion - 1.496v - ASUS P5E - by ----------- karl_eller
Q6600 G0 - L726A915 - 3.5Ghz P stable - AC TR Ultra 120 E - 1.41v - ASUS P5B Dlx - by -------------- -n7-
Q6600 B3 - L725A883 - 3.5Ghz (438x8) P stable - WC D-Tek Fuzion - 1.425v - EVGA 680i - by ------ laydback
Q6600 G0 - L727A673 - 3.42Ghz P stable - AC Tuniq Tower - 1.375v - ASUS P5K Dlx - by ------------timber715
Q6600 G0 - L727A934 - 3.42Ghz P stable - WC - 1.43v - ASUS P5K Dlx - by -------------------------njkid32
Q6600 G0 - L720B013 - 3.4Ghz P stable - AC TR 120 Ultra - 1.375v - ASUS P5K Dlx - by -------------sobol
Q6600 B3 - L645G523 - 3.4Ghz (425x8) P stable - AC TR Ultra 120 - 1.44v - EVGA 680i - by ----------zodduska
Q6600 G0 - L726A855 - 3.4Ghz P stable - AC TR Ultra 120 - 1.55v - Gigabyte GA P35 DS3R - By ------road-runner
Q6600 B3 - L644G135 - 3.3Ghz P stable - AC Scythe Infinity - 1.4v DFI P965S - by ------------------The Nemesis

Xeon X3220 Table--------------------------
X3220 B3 - L640F058 - 3.6Ghz P stable -WC Apogee GTX - 1.6v - DFI 680i - by ------------------VirtualRain

Xeon X3210 Table--------------------------
X3210 G0 - L723A*** - 3.6Ghz P stable - WC D-Tek Fuzion - 1.42v - ASUS P5K Prem - by --------sofarfrome

WP & 32m Stable Results------------------
Q6600 G0 - L723A924 - 4.41 Ghz Wp 1024m stable -PC Vapo LS - 1.68v - Abit IP35-Pro - by - -----ncsa
Q6600 G0 - L721A814 - 4.2Ghz Wp 32m stable - WC Apogee GTX - 1.68v - DFI UT P35-2TR - by ---sco999
Q6600 G0 - L722A784 - 4.11Ghz Wp 32m stable - WC - 1.56v - ASUS P5K Dlx - by -----------------njkid32
Q6600 G0 - L738B065 - 4.05Ghz Pi 32m stable -WC EK Supreme - 1.562v - ASUS Maximus Ext -- by polar bear
Q6600 G0 - L726A850 - 4.03Ghz 32m stable - AC TR Ultra 120 - 1.612v - ASUS P5K Dlx - by --------crossg
Q6600 B3 - L634A700 - 3.9Ghz 32m stable - AC TR Ultra 120 - 1.58v - ASUS P5K Dlx - by ----------BND|MOD
Q6600 B3 - **(ES)** - 3.8Ghz 32m stable - AC TR Ultra 120 - 1.5v - ASUS P5K Dlx - by -----------BND|MOD ****single 32m Pi stable****
Q6600 B3 - L634A700 - 3.72Ghz Wp 1024m stable - WC Apogee GT - 1.55v - ASUS P5K Dlx - by ----BND|MOD
Q6600 G0 - L720B028 - 3.6Ghz 32m stable - WC Reserator 1 - 1.5v - ASUS P5K Dlx - by ------------yobi ****single 32m pi stable****

dave_graham

09-04-2007, 07:46 AM

keep me in the loop on this as well.

i'm trying to track stuff offline.

dave

CraptacularOne

09-04-2007, 07:54 AM

keep me in the loop on this as well.

i'm trying to track stuff offline.

dave

lol. I'm asking people that have one to post up and see what is doing what ;) I need people to post some results so I can add them to the table and we can compare side by side rather than searching through a 1,000 post thread to find the answers we seek :)

Ic3man

09-04-2007, 08:14 AM

Great idea and worthy of a sticky if it gets updated often.

sofarfrome

09-04-2007, 08:16 AM

How about accepting all quads? I already have a 3.6GHz stable X3210 to add to the list.

sobol

09-04-2007, 08:16 AM

lol. I'm asking people that have one to post up and see what is doing what ;) I need people to post some results so I can add them to the table and we can compare side by side rather than searching through a 1,000 post thread to find the answers we seek :)

How about if you put some effort in it go through all forums and all threads and gather those informations your self ? That would be good start and I'm sure many people will post their results then.

aspms*

09-04-2007, 08:42 AM

Let it be first on the line! :D

1) G0
2) L723A674
3) Validation @4.2Ghz (http://valid.x86-secret.com/show_oc.php?id=236015)
4) 3.81Ghz Prime stable 9h+
http://img258.imageshack.us/img258/811/primestable381ghzalmostxf3.th.jpg (http://img258.imageshack.us/my.php?image=primestable381ghzalmostxf3.jpg)

5) w/c (Apogee GT)
6) 1.54V
7) Gigabyte P35-DS4 bios F6a (beta)

*) 3D benchable @ 4.05Ghz 1.55V

CraptacularOne

09-04-2007, 09:24 AM

How about accepting all quads? I already have a 3.7GHz stable X3210 to add to the list.

That is fine I will accept all quads but I will make separate lists for each :)

veilsidebr

09-04-2007, 09:44 AM

i shall post my settings when i get home, but anyways i use it daily at 3.0, dunno if this is an interesting mark, ROCK stable, B3 stepping.

njkid32

09-04-2007, 09:59 AM

1) G0
2) L723A963
3) CPU-Z Validation
4) http://www.njkidxs.org/L723A963-3.7-1.43v.jpg
5) Water
6) 1.43v
7) Asus P5K DLX
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1) G0
2) L726A840
3) CPU-Z Validation
4) http://www.njkidxs.org/L726A840-3.6.jpg
5) Water
6) 1.41v
7) Asus P5K DLX
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1) G0
2) L726A
3) CPU-Z Validation
4) http://www.njkidxs.org/L726A-3.8-1.43v-2.jpg
5) Water
6) 1.43v
7) Asus P5K DLX
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1) G0
2) L7272A934
3) CPU-Z Validation
4) http://www.njkidxs.org/L7272A934-3420-1.34v
5) Air
6) 1.34v
7) Asus P5K DLX
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

More to come:p:

The Nemesis

09-04-2007, 10:16 AM

Q6600 L644G135 "B3"
DFI P965-S
Scythe Infinity Stock
HSPC Top Deck Tech Station
OCZ GameXtreme 700W

3.6 Ghz 32 Mb Pi 3-3-3-10 DDR2-800 1.43v
http://img375.imageshack.us/img375/8853/36ghz32mbpi33310ocztitakc3.th.jpg (http://img375.imageshack.us/my.php?image=36ghz32mbpi33310ocztitakc3.jpg)
3.6 Ghz 32Mb Pi 4-3-3-9 DDR2-800 1.43v
http://img375.imageshack.us/img375/9460/36ghz32mbpi4339ocztitanig6.th.jpg (http://img375.imageshack.us/my.php?image=36ghz32mbpi4339ocztitanig6.jpg)
3.6 Ghz 32 Mb Pi 5-5-5-15 DDR2-1200 1.43v
http://img375.imageshack.us/img375/5697/36ghz32mbpi55515ocztitakp8.th.jpg (http://img375.imageshack.us/my.php?image=36ghz32mbpi55515ocztitakp8.jpg)

12 + Hours Prime 3.3Ghz 1.4vcore 1.36vdroop
http://img475.imageshack.us/img475/9185/12hoursprime33ghz137vdrnl7.th.jpg (http://img475.imageshack.us/my.php?image=12hoursprime33ghz137vdrnl7.jpg)

GameGuru

09-04-2007, 10:24 AM

OK I would like to start a Quad Core Database so we can all post and see what steppings are doing what. All quads are welcome and I will have individual categories for each model. So post up and lets do something useful :)

So here's the deal, give me....
1) Post your Core revision (B3 or G0)
2) Week (L726A...ect)
3) CPU-Z Validation
4) Screen shot of it running at that speed (orthos, prime95..ect) 100% load
5) Cooling being used
6) Voltage

I will accept a Pi 32m run as well but please stable OCs only, I will keep the thread up to date. So lets see what you guys got :)

It might also be a good idea to post which board people are using. Every bit helps :)

Loony

09-04-2007, 10:34 AM

It might also be a good idea to post which board people are using. Every bit helps :)

That's a good point, also putting what they use to cool the CPU instead of just water/air would be good, just a short description. :shrug:

CraptacularOne

09-04-2007, 10:40 AM

It might also be a good idea to post which board people are using. Every bit helps :)

Done :)

CraptacularOne

09-04-2007, 10:54 AM

That's a good point, also putting what they use to cool the CPU instead of just water/air would be good, just a short description. :shrug:

OK :up:

yobi

09-04-2007, 11:07 AM

333
and 400:)

CraptacularOne

09-04-2007, 11:10 AM

@ yobi, I need the batch number of your chip, voltages, cooling..ect ;)

yobi

09-04-2007, 12:05 PM

batch number L720B028
voltages 3Ghz 1.36V 3,6GHz 1.5V
cooling zalman reserator 1 plus

http://valid.x86-secret.com/show_oc.php?id=238522

BNDMOD

09-04-2007, 12:15 PM

1) B3
2) ES
3) Validation @4.0Ghz (http://valid.x86-secret.com/show_oc.php?id=223277)
4) 3.6Ghz

Prime
http://img210.imageshack.us/img210/678/prime954instanciasfulllsi5.th.jpg (http://img210.imageshack.us/my.php?image=prime954instanciasfulllsi5.jpg)

Sp32M Dual
http://img108.imageshack.us/img108/1998/sp32mdualcore2ycore4lc2.th.jpg (http://img108.imageshack.us/my.php?image=sp32mdualcore2ycore4lc2.jpg)

5) TR Ultra 120 eXtreme + SilverStone FM 121
6) 1.475V
7) Asus P5K Deluxe WiFi-AP - 0404 bios Version
*) 3D benchable @ 3.9Ghz 1.55V

CraptacularOne

09-04-2007, 12:16 PM

batch number L720B028
voltages 3Ghz 1.36V 3,6GHz 1.5V
cooling zalman reserator 1 plus

I'll put you on the list by can you get me screenie of it priming at that speed? or a 32m Pi? Thanks :)

yobi

09-04-2007, 01:07 PM

3GHz & 3,6GHz:)

njkid32

09-04-2007, 01:14 PM

1) G0
2) L722A784
3) CPU-Z Validation
4) http://www.njkidxs.org/wprime-4113-2.jpg
5) Water
6) 1.56v
7) Asus P5K DLX

vocch

09-04-2007, 01:18 PM

Q6600 G0 - L720B062 - 3.51Ghz stable - AC TR Ultra 120 A - 1.45v by vocch

Here you go craps a copy n paste lol.
http://valid.x86-secret.com/show_oc.php?id=238556
Have not maxed mine due to old board have used @ 3.6ghz but not tested stabiliy....but saying that 3.51ghz 1.45v in bios-air- on an old DS4 P965 r.1.0...can't grumble.:)

http://img117.imageshack.us/img117/1374/8hrsstablelargewr2.jpg (http://imageshack.us)

CraptacularOne

09-04-2007, 01:22 PM

cfree1012

09-04-2007, 01:23 PM

q6600 g0 3.76Ghz 1.475v
L720B023
watercooling
p5k premium

http://forums.extremeoverclocking.com/attachment.php?attachmentid=107407&d=1188446347

vocch

09-04-2007, 01:50 PM

Very nice! craps...i would add a cpu-z to mine above but it don't wanna play....don't know if the beta has had anything to do with it but the new 1.41 seems to think i'm corupt lol...and an earlier version tells me to upgrade so i give up!....take a look.

http://valid.x86-secret.com/show_oc.php?id=238517

File cpuz_20.cvf upload : OK
Checksum Computed : OK
Checksum Validated : YES
ERROR ! Your CPUZ Version is outdated. Please upgrade to CPU-Z 1.41+

CraptacularOne

09-04-2007, 02:20 PM

q6600 g0 3.76Ghz 1.475v
L720B023
watercooling
p5k premium

http://forums.extremeoverclocking.com/attachment.php?attachmentid=107407&d=1188446347

I'm going to need some validation pics friend :)

@ vocch, thanks, that's not all it got, she'll do 4Ghz
http://valid.x86-secret.com/show_oc.php?id=237382
but it's no fun unless it's stable...lol Which I'm working on getting that to ;)

And try CPU-Z 1.40.5 :toast:

AcuraDC5

09-04-2007, 02:21 PM

OK I would like to start a Quad Core Database so we can all post and see what steppings are doing what. All quads are welcome and I will have individual categories for each model. So post up and lets do something useful :)

So here's the deal, give me....
1) Post your CPU model & Core revision (B3 or G0)
2) Week (L726A...ect)
3) CPU-Z Validation
4) Screen shot of it running at that speed (orthos, prime95..ect) 100% load
5) Cooling being used
6) Voltage
7) Motherboard used (this is optional but helpful just the same:))

I will accept a Pi 32m run as well but please stable OCs only, I will keep the thread up to date. So lets see what you guys got :)

Should add RAM speed and brand as well (stock and OC) and mobo.

CraptacularOne

09-04-2007, 02:26 PM

Should add RAM speed and brand as well (stock and OC) and mobo.

This is only for CPUs :) There is 3 different threads in the bandwidth section that deal with memory and it's speeds. I'm only trying to concentrate on quad core CPUs :)

BNDMOD

09-04-2007, 02:33 PM

1) B3
2) ES
3) Validation @4.0Ghz
4) 3.0Ghz

Prime
http://img208.imageshack.us/img208/9857/prime954instanciasfulloz6.th.jpg (http://img208.imageshack.us/my.php?image=prime954instanciasfulloz6.jpg)

5) TR Ultra 120 eXtreme + SilverStone FM 121
6) 1.20V
7) Asus P5K Deluxe WiFi-AP - 0404 bios Version
*) 3D benchable @ 3.9Ghz 1.55V

================================================== ===
1) B3
2) ES
3) Validation @4.0Ghz
4) 3.8Ghz

Sp32m
http://img523.imageshack.us/img523/2645/sp32m422x944410hq8.th.jpg (http://img523.imageshack.us/my.php?image=sp32m422x944410hq8.jpg)

5) TR Ultra 120 eXtreme + SilverStone FM 121
6) 1.50V
7) Asus P5K Deluxe WiFi-AP - 0404 bios Version

no_n|ck

09-04-2007, 02:45 PM

OK suppose it's time for the thread starter to post up some goodies huh?

1) Q6600 G0
2) L726A840
3) http://valid.x86-secret.com/show_oc.php?id=237378
4)http://xs219.xs.to/xs219/07362/39ghzprime.jpg.xs.jpg (http://xs.to/xs.php?h=xs219&d=07362&f=39ghzprime.jpg)
5) Apogee GT
6) 1.54v
7) EVGA 680i A1
------------------------------------

no offense, but whats the point of 30min prime shot. Is that enough to be consider stable? I atleast want a 2-3h prime pass, to consider my system stable. Btw, what was the voltage taken here (bios), what was the temps?

here is mine at 3.8ghz, 14h prime shot..

http://img167.imageshack.us/img167/4246/380014hka5.th.jpg (http://img167.imageshack.us/my.php?image=380014hka5.jpg)

1) Q6600 G0
2) L726A951
3) no max frq. shot yet taken
5) D-Tek Fuzion
6) 1.502v (1.55 set in bios, 1.52 off load in wins)
7) Asus P5K Deluxe

CraptacularOne

09-04-2007, 02:52 PM

@ BND|MOD, please if that is the same chip, only enter it once :)

BNDMOD

09-04-2007, 02:54 PM

@ BND|MOD, please if that is the same chip, only enter it once :)

Yes... the same chip :( sorry... but i think that is posible have more than one result, with diferrent vcore.. :)
but no problemªªª :up:

CraptacularOne

09-04-2007, 02:56 PM

no offense, but whats the point of 30min prime shot.

I want Prime or orthos, but will take a 32m run incase you don't have your 2-8hous screenie available. This is going on the honor system, so if you lie you are only hurting yourself. This isn't a bragging rights thread but a thread to help see what stepping are doing what. I think that most of the users here would like something like this and are responsible enough to not post a BS OC....It all comes out in the wash though, if down the road we see someone that posted a fantastic OC on what we discover to be a garbage stepping, we'll know who's full of it ;)

And I'll highlight is OC and put a nice little note next to it so everyone can see that he is FOS :)

I'll add a line if it's 32m or prime stable, that should help no?

[XC] 4X4N

09-04-2007, 03:18 PM

Hopefully we can keep this to just results. Would be nice to have a good database. Here's my best stable settings. Can bench higher, but not 24/7 stable.

Q6600 G0 723A825
3.6 @ 1.42v or 3.5 @ 1.35
Cooling: TR Ultra 120 Extreme

http://img159.imageshack.us/img159/641/9x400prmxo2.th.jpg (http://img159.imageshack.us/my.php?image=9x400prmxo2.jpg)http://img256.imageshack.us/img256/572/9x389qprmhb8.th.jpg (http://img256.imageshack.us/my.php?image=9x389qprmhb8.jpg)

no_n|ck

09-04-2007, 03:28 PM

I want Prime or orthos, but will take a 32m run incase you don't have your 2-8hous screenie available. This is going on the honor system, so if you lie you are only hurting yourself. This isn't a bragging rights thread but a thread to help see what stepping are doing what. I think that most of the users here would like something like this and are responsible enough to not post a BS OC....It all comes out in the wash though, if down the road we see someone that posted a fantastic OC on what we discover to be a garbage stepping, we'll know who's full of it ;)

And I'll highlight is OC and put a nice little note next to it so everyone can see that he is FOS :)

I'll add a line if it's 32m or prime stable, that should help no?

yea, whateva, just i think if someone is watching to bought himself a nice batch, it would be cool to post beside taken Prime95 time, so he could have some clue about certian stability. Or just put link to the screen shot of certian OC.

btw, BND|MOD's B3 ES isnt prime stable at 3.8, instead 32m pi..

crossg

09-04-2007, 03:41 PM

Q6600 G0 726A850
3.6 @ 1.4125v (Bois) 1.3840 Load (http://www.xtremesystems.org/forums/showpost.php?p=2396140&postcount=866)
Cooling: TR Ultra 120 Extreme (Lapped)

Some benches @4030 (http://www.xtremesystems.org/forums/showpost.php?p=2407618&postcount=1036)

File cpuz_20.cvf upload : OK
Checksum Computed : OK
Checksum Validated : YES
ERROR ! Your CPUZ Version is outdated. Please upgrade to CPU-Z 1.41+
Yes I got the same thing but 1.41 is up on the CPU-Z site and it works fine.:)

AcuraDC5

09-04-2007, 05:28 PM

This is only for CPUs :) There is 3 different threads in the bandwidth section that deal with memory and it's speeds. I'm only trying to concentrate on quad core CPUs :)

But your overclock depends on your ram speeds as well.

nugzo

09-04-2007, 05:47 PM

1) Q6600 G0
2) L724A760 (I have 2 of these exact batch. They both perform Identical, same vcore, same OC, same temps. Your decision if you want to add it twice)
3) Cooling PA120.3, Fusion, D5
4) 1.49v Bios/windows/load (vdroop mod) in screen shot. I've since been able to lower to 1.45 completely stable.
5) EVGA 680i p30 bios

http://img452.imageshack.us/img452/8243/37008xstableqt2.th.jpg (http://img452.imageshack.us/my.php?image=37008xstableqt2.jpg)

rbsmontemor

09-04-2007, 05:58 PM

1) Q6600 G0
2) L719B
3) Cooling TR Ultra-120
4) 1.385v Bios, 1.376 windows/load (vdroop mod).
5) Asus P5K Deluxe 0501 Beta.

http://img465.imageshack.us/img465/3727/sassaqprimepv9.jpg

Still testing...

Rbs.

CraptacularOne

09-04-2007, 08:10 PM

List updated, errors fixed :) It looks like so far that 3.6Ghz is pretty much a safe bet with the G0 :) Keep em coming guys :toast:

njkid32

09-04-2007, 08:12 PM

You might want to add wprime as a stability test.

CraptacularOne

09-04-2007, 08:14 PM

You might want to add wprime as a stability test.

done :)

dragonhunter

09-04-2007, 08:23 PM

Q6600 GO
L727A934
Stock Vapo LS
1.425Vcore with Damper enable
Asus P5K Premium
-Core Temp in the Pic is NOT trusted because it's the same at idle and load :confused:

http://img205.imageshack.us/img205/8371/snap1sj0.jpg (http://imageshack.us)

CraptacularOne

09-04-2007, 08:27 PM

Q6600 GO
L727A934
Stock Vapo LS
1.425Vcore with Damper enable
Asus P5K Premium
-Core Temp in the Pic is NOT trusted because it's the same at idle and load :confused:

Nice clocks, but can I get a 32m or Prime screenie please? :toast:

dragonhunter

09-04-2007, 09:01 PM

Nice clocks, but can I get a 32m or Prime screenie please? :toast:

Here are 32M and Prime95 in one. This chip can go higher but my stock Vapo can't handle the heatload so I stop at 4ghz for 24/7 usage. Sorry for the big Pic.

http://img441.imageshack.us/img441/7488/untitledms2.jpg (http://imageshack.us)

aspms*

09-04-2007, 09:24 PM

I would like to advice to include time of priming and show it in your first pages table! ;)

Because you can't call your system stable after testing 30min prime or so!

Mine too can pass 30min of prime @ 3.95Ghz, but really stable with hours (10h+) of priming I can get only ~3.81Ghz! :rolleyes:

Then let me know what would you like to see from me in your table 3.95Ghz "P stable" or 3.81Ghz really stable for 24/7 with same words "P stable"? :rolleyes:

no_n|ck

09-05-2007, 02:42 AM

CraptacularOne

09-05-2007, 04:04 AM

ocZZZ

09-05-2007, 04:38 AM

Q6600 G0
L723A963
3.6ghz @ 1.475v (bios) 1.472v (real)
Asus P5K Premium
Tuniq Tower

http://img504.imageshack.us/img504/4128/36ghz1475vpx4.jpg (http://imageshack.us)
http://img504.imageshack.us/img504/4128/36ghz1475vpx4.0d2f26b678.jpg (http://g.imageshack.us/g.php?h=504&i=36ghz1475vpx4.jpg)

The Nemesis

09-05-2007, 05:24 AM

I'd rather the 3.3Ghz prime stable be listed than the 3.6Ghz 32mb Pi.....

TinTin

09-05-2007, 05:27 AM

1) Q6600 G0
2) L724A784 Pack Date: 7/13/2007
3) WaterCooling: Black Ice GT Extreme, Vortex XP(FuZion), D5
4) 445X9, 1.62V Dual Ortho small FFT 30mins.
5) Asus P5K Premium BIOS 204

http://img184.imageshack.us/img184/6723/20070807224620auc5.jpg

sobol

09-05-2007, 05:48 AM

1) Q6600 G0
2) L720B013 Pack Date: 07/31/2007
3) Screen shot below
4) Screen shot below
5) ThermalRight 120 Ultra Extreme + MOD + S-FLEX SFF21E
6) 1.375v bios, 1.368v windows
7) Asus P5K Deluxe, Bios 0404

This one max stable is 3400mhz. It won't do even 3450 mhz (BSOD).

http://img391.imageshack.us/img391/6859/34004gbjw2.jpg

CraptacularOne

09-05-2007, 06:39 AM

List updated :)

@ The Nemesis, request taken :)

Keep posting guys :)

phelan1777

09-05-2007, 06:43 AM

Will post my QX6700 shortly,

I also have a 3220, which is Qcore, taken results for that as well?

(more info to follow)

CraptacularOne

09-05-2007, 07:33 AM

Will post my QX6700 shortly,

I also have a 3220, which is Qcore, taken results for that as well?

(more info to follow)

If it's got four cores, I'll take it :) Just give me the usual specs and I'll put it up there :)

[XC] 4X4N

09-05-2007, 08:01 AM

Was just looking at the data base, looking good :up: Sorry I forgot motherboard. It's the gigabyte DS3-R in my sig.

CraptacularOne

09-05-2007, 09:27 AM

4X4N;2412961']Was just looking at the data base, looking good :up: Sorry I forgot motherboard. It's the gigabyte DS3-R in my sig.

Thanks :up:

CraptacularOne

09-05-2007, 03:04 PM

anyone else?

dragonhunter

09-05-2007, 04:37 PM

Why is PI can be use as stability and Folding can't?
Folding uses all 4 cores and PI only use 1 core.
Just a thought......

Xiphias-Gladius

09-05-2007, 05:45 PM

Ok, here's mine:

Q6600 G0 @ 3700 1,44V (9x412)
L719B272
Gigabyte P35 DS4
Swiftech Storm G4 Rev2

http://i224.photobucket.com/albums/dd241/xiphias-gladius/Q660037-1.jpg

GripS

09-05-2007, 05:54 PM

Q6600 @ 3.4ghz with 1.4v BIOS 1.37v load
Batch: L724A760 VID: 1.2875
DFI Infinity P965-S
Scythe Infinity with 2x120mm fans in push/pull

Stable:

http://img2.freeimagehosting.net/uploads/th.c77142821b.jpg (http://img2.freeimagehosting.net/image.php?c77142821b.jpg)

Suicide:

http://img2.freeimagehosting.net/uploads/th.e151dffc2c.jpg (http://img2.freeimagehosting.net/image.php?e151dffc2c.jpg)

CraptacularOne

09-05-2007, 07:54 PM

OK folks, I am going to change the 32m Pi requirement to a quad instance as that should help :)

List up dated :)

@ BND|MOD & yobi, please submit a quad instance of 32m Pi and I will remove the disclaimer next to your results :)....or better yet a Prime stable screenie ;)

no_n|ck

09-06-2007, 08:43 AM

update;

3850Mhz@1.52v (same vcore as for 3800Mhz), 2h Prime95 pass..

http://img46.imageshack.us/img46/5761/38502haq0.th.jpg (http://img46.imageshack.us/my.php?image=38502haq0.jpg)

It passed 30min Prime @ 3910Mhz at this voltage, but one core craped out on 44min, wich i dont considerd it stable..

CraptacularOne

09-06-2007, 10:03 AM

CraptacularOne

09-06-2007, 05:15 PM

c'mon guys let's get some more results posted :toast:

RLM

09-06-2007, 05:56 PM

I don't have this chip anymore. Still trying to dig out the full stepping, but it was L724Axxx

These two runs I've dug up are on different kit. An Abit IP35 pro and a DFI P35-T2R. Hopefully of use.

Q6600 GO 423x9 (3.8 ghz) Mem 1016mhz 4-4-4-12 Prime Blend Test
http://img235.imageshack.us/img235/8342/20minblendcn5.jpg

http://img511.imageshack.us/img511/5650/q6600bench1mb4.jpg

I had a L723B, but didn't hold on to it long enough for any serious testing.

Currently have a L723A365. Haven't a clue about this chip. Looking forward to checking it out.

RLM

noobzed

09-06-2007, 05:59 PM

possible to add fsb and ratio in database ?

crossg

09-06-2007, 07:01 PM

Q6600 G0 726A850 @ 3816
1.5250 vcore Bios / 1.4960 Actual
TRUE Lapped.
http://valid.x86-secret.com/show_oc.php?id=239384

Prime95 Large FFT 3 hours 20 min. Click (http://www.xtremesystems.org/forums/showpost.php?p=2415990&postcount=1102)

CraptacularOne

09-06-2007, 07:48 PM

possible to add fsb and ratio in database ?

Sure, but so far everyone has used the stock multi (except me with my QX6700) that their CPU comes with, so there's no need. But this thread isn't about max FSB of a chip, but about the max stable operating speed they can achieve. The motherboard is the determining factor in the highest potential FSB a chip can get to. My board can only do a little more than 450Mhz FSB
http://valid.x86-secret.com/show_oc.php?id=239025
And I am 100% certain that if put this chip in a P35 board that I will be able to attain a higher FSB, but my chips max stable speed is only 3.9Ghz (434x9) and that I can attain that on my current board. :)

And list updated again, we can already see a patern forming with the L726A chips on this table so keep those results coming :up:

nugzo

09-06-2007, 09:55 PM

I didn't use stock multi. I use 8 on all of my quads.

zodduska

09-07-2007, 01:54 PM

(duping my post from the other db thread)

my 24/7 oc:

Q6600 B3 L645G523
3.4ghz (425x8 1.44v)
Evga 680i NF68-A1(570)
Thermalright Ultra 120 Extreme

10+ hour p95 large fft, 11+ hour p95 small fft stable, 23 hour xvid DEcode loop

before I RMA'd this mobo it was fully stable except xvid would lock, now it's all good :D

http://img529.imageshack.us/img529/8605/3400stableei2.th.jpg (http://img529.imageshack.us/my.php?image=3400stableei2.jpg)

valid: http://valid.x86-secret.com/show_oc.php?id=239739

now for a little stability contrast, same cpu:
32m super pi, 3dmark06 stable 3.7ghz

http://img380.imageshack.us/img380/774/3712ctk0yn8.th.jpg (http://img380.imageshack.us/my.php?image=3712ctk0yn8.jpg)

http://img120.imageshack.us/img120/1175/37123d2k6xv2ex1.th.jpg (http://img120.imageshack.us/my.php?image=37123d2k6xv2ex1.jpg)

doom_st

09-08-2007, 01:19 AM

1) Q6700 ES (G0)
2) L713A358
3) http://valid.x86-secret.com/show_oc.php?id=239884
4)
Prime 95 (Blend)8h+
http://img169.imageshack.us/img169/4232/shot0001fe0.th.jpg (http://img169.imageshack.us/my.php?image=shot0001fe0.jpg)
5) PC
6) 1.52
7) Abit IP35 PRO

aspms*

09-08-2007, 01:52 AM

doom_st

09-08-2007, 03:36 AM

no custom phase build by me&unseen

CraptacularOne

09-08-2007, 08:31 AM

List updated :toast:

drynyks

09-08-2007, 08:44 AM

Look at the Ballistix go! 24/7 overclock 15 hours prime stable

1. Q6600 G0
2. L727A934
3. Screenshot below
4. Screenshot below
5. Water Cooling
6. 1.425bios 1.4windows
7. P5b Deluxe

http://home.comcast.net/~drynyks/15hr3636.jpg

CraptacularOne

09-08-2007, 08:49 AM

drynyks, what water block are you using? Nice result too :up:

drynyks

09-08-2007, 08:51 AM

Thanks CraptacularOne. I could squeeze more out of it for certain but this is where it's staying for now. I am using a D-Tek FuZion.

CraptacularOne

09-08-2007, 08:54 AM

Thanks CraptacularOne. I could squeeze more out of it for certain but this is where it's staying for now. I am using a D-Tek FuZion.

Well a 3.6Ghz quad isn't exactly "slow" by any stretch of the imagination :) When you do decide to push higher post it up and update your results :toast:

virtualrain

09-08-2007, 10:20 AM

Here's my latest...

X3220 B3 - L640F058 - 3.6Ghz P stable - Apogee GTX - 1.6v DFI 680i - by --------------VirtualRain

Thankfully I have good cooling because the Vcore required for Prime stability is Xtreme (1.6V idle drooping to 1.55V load)!

http://members.shaw.ca/virtualrain/OC/blend-stable-3600.jpg

mjb1206

09-08-2007, 11:02 AM

How about some stable overclocks?? Everything posted has minimal Orthos / Prime95 runs, which basically anyone can do! Plenty posts with 2-min., 5-min., 10-min., 20-min. runs, lets see some real stable overclocks.

How about some 6-12 hour Orthos / Prime95 stability run................... Come on guys show off what ya got!!

sofarfrome

09-08-2007, 01:53 PM

Xeon X3210 Go
Week - L723A
3.8GHz validation (http://valid.x86-secret.com/show_oc.php?id=237217)
WC rig in sig
Voltage = 1.42vcore
Asus P5K Premium

There is a lot more left in it too. I have been working on 3.8GHz at 1.47vcore

sergmann

09-08-2007, 02:08 PM

Super Pi

http://www.abload.de/thumb/superpi12.125cpu4158ram554inx.jpg (http://www.abload.de/image.php?img=superpi12.125cpu4158ram554inx.jpg)

24/7 Settings

http://www.abload.de/thumb/37quadprimefast3stunden145vmfj.jpg (http://www.abload.de/image.php?img=37quadprimefast3stunden145vmfj.jpg)

sam95ta

09-08-2007, 03:52 PM

Drynyks great overclock.I also have a p5b,wondering what you have northbridge set at.Have you hit a wall at anything over 404fsb like I have.Thinking of upgrading to a p35 or x38.

noobzed

09-08-2007, 04:21 PM

you all have great q66 g0 mine want 1,48 to do 450x8 .... think i gat a bad cpu..

strange thing also coretemp always show me wrong freq but C1E is disabled..

no_n|ck

09-08-2007, 04:53 PM

you all have great q66 g0 mine want 1,48 to do 450x8 .... think i gat a bad cpu..

strange thing also coretemp always show me wrong freq but C1E is disabled..

its still 50% overclock!
btw, coretemp is showing wrong freq, if the multi isnt set to 9×..

CraptacularOne

09-08-2007, 09:24 PM

List updated :)

@ sergmann, I'm going to need your week (FPO Batch #) to make your result useful :)

@virtualrain, very helpful posting in the format I keep the table in :up: simple copy and paste :toast:

drynyks

09-09-2007, 12:10 AM

How about some stable overclocks?? Everything posted has minimal Orthos / Prime95 runs, which basically anyone can do! Plenty posts with 2-min., 5-min., 10-min., 20-min. runs, lets see some real stable overclocks.

5 posts above you saying this is mine which is 15hours prime.

Here's my latest...

X3220 B3 - L640F058 - 3.6Ghz P stable - Apogee GTX - 1.6v DFI 680i - by --------------VirtualRain

virtualrain try running your prime with small FFT's. That is best for testing processor stability with Prime95.

Drynyks great overclock.I also have a p5b,wondering what you have northbridge set at.Have you hit a wall at anything over 404fsb like I have.Thinking of upgrading to a p35 or x38.

Thanks sam95ta. You know I played with my overclock a bit more and I have previously done 10hours prime at 405 with this board but it looks near the max. I am sort of burnt on messing with it but I'm sure I'll be playing with it more.
My settings in bios are:

CPU VCore Voltage 1.425
FSB Termination Voltage 1.450
NB VCore 1.65

sergmann

09-09-2007, 01:11 AM

@ CraptacularOne

The Batch is L726A601

3NZ0

09-09-2007, 04:21 AM

1) Q6600 G0 @ 3.6ghz
2) L719B271
5) Tuniq tower with the fan on low medium (quiet)
6) 1.39v set in the bios (cpu-z doesn't seem to report it correctly)
7) P35 DQ6 Rev.1 F5

http://img101.imageshack.us/img101/9264/6hrs4minsrr3.jpg (http://imageshack.us)

CraptacularOne

09-09-2007, 06:42 AM

List up dated :)

@ sergmann, what cooling and mobo did you you use?

sobol

09-09-2007, 10:48 AM

Hi Here is my second Q6600

1) Q6600 G0
2) L724A900 Pack Date: 08/28/2007
3) Screen shot below
4) Screen shot below
5) ThermalRight 120 Ultra Extreme + MOD + S-FLEX SFF21E
6) 1.450v bios, 1.432v windows
7) Asus P5K Deluxe, Bios 0404

http://sobol.org/~sobol/3600-4gb-mprime.jpg

cfree1012

09-09-2007, 11:31 PM

q6600 g0 @3.76Ghz
L720B023
WC (swiftech apogee)
1.475v bios
Asus p5k premium.

http://img454.imageshack.us/my.php?image=376ghz1hrstableallcoresbd0.jpg

virtualrain

09-09-2007, 11:56 PM

virtualrain try running your prime with small FFT's. That is best for testing processor stability with Prime95.

I agree... What made you think I didn't know that?

I find small FFT's really stress the CPU and Blend obviously does both CPU and memory. Typically I OC the processor first with memory underclocked and get small FFT stability and then OC the memory and run Blend. I have found that your OC may pass small FFT but when you start overclocking the memory you will fail blend. I insist on all my OC's passing both for 8+hrs to be satisfied... My OC also passed 8+hrs of Small FFT as well...

http://members.shaw.ca/virtualrain/OC/small-fft-stable-3600.jpg

turtletrax

09-10-2007, 12:05 AM

1) Q6600 G0
2) L724A629
3) http://valid.x86-secret.com/show_oc.php?id=224953
4) http://img.photobucket.com/albums/v699/turtletrax/4HoursPrime4Ghz.jpg
5) CPU Loop: DDC-2 Petra topped, Thermochill HE 120.3, D-Tek Fuzion, MCRes Micro
5.1) GPU/Chipset Loop: DDC-2 Petra topped, Thermochill PA 120.2, EK 8800GTX, 2xMCW-30, "T" line
6) 1.6 DMM
7) EVGA 680i "A1"

I did this run before I had done the Pencil "Droop" mod and will retry for much lower Vcore.

CraptacularOne

09-10-2007, 12:51 PM

List up dated :toast:

Got a stable quad core? Post it here guys :)

Coroner Kyle

09-10-2007, 01:48 PM

1) Q6600 G0
2) L724A629

What's the VID on this beast?

turtletrax

09-10-2007, 02:18 PM

What's the VID on this beast?

VID is 1.275v

I am out of FSB on my 680i so I am waiting to get more info on X38 so I can decide on wether to get it or a p35 based board. I really want to see what this chip maxes out on a good board. The EVGA isnt a bad board but there is better ;)

njkid32

09-10-2007, 02:33 PM

Hmm it seems you've got a similar clocker to mine:D Nice cpu turtletrax:up: I bet your cpu does much better on a P35.

turtletrax

09-10-2007, 02:58 PM

Thanks nj ;)

What amazes me is the Vcore needed for 3.6ghz. I can prime all day long with 1.36Vcore and load temps of 45c. This is my 24/7 OC and I am really happy with that.

Looking forward to a new board, but wont pull the trigger untill X38/48 rear their heads. Hoping to match your stellar OC :up:

njkid32

09-10-2007, 03:40 PM

Oh just wait till you put the cpu in a P35 you'll see you can use lower vcore for 3.6ghz. Just remember on P35 to set all volts manually because when on auto they raise automatically with the fsb;)

turtletrax

09-10-2007, 03:55 PM

Oh just wait till you put the cpu in a P35 you'll see you can use lower vcore for 3.6ghz. Just remember on P35 to set all volts manually because when on auto they raise automatically with the fsb;)

Thanks for the heads up :)

I am sooo tempted to get a p35 now, but I really should wait 'n see.

njkid32

09-10-2007, 03:58 PM

You'll see very little if any performance increase with x38. So, this is why I am staying with P35 till x48 is available:)

turtletrax

09-10-2007, 04:00 PM

Hmmmm, your not helping my wallet nj :p:

I am hoping to sell my 680i to a friend (thats you patriote!!!:D ). As soon as I do I will decide. I dunno if I will go with the P5K premium or the DFI. Hmmm, so many decisions!!!

turtletrax

09-10-2007, 08:50 PM

CraptacularOne

09-10-2007, 09:38 PM

Is there a 4Ghz Quad club yet??? If not, we need an Avatar and a new thread for application :cool:

Any thoughts nj or others??

Edit: Post 300 :) At this pace I should have 1000 in about 6 years :ROTF:

I'll be in on that :cool: I've got 4Ghz stable on my Q6600, but I'm trying to get this now
http://valid.x86-secret.com/show_oc.php?id=241138

It'll pass for about 1 hour then a core craps out on me, while the other 3 soldier on. I'm going to try lapping it and see if that helps tomorrow, if not I'll post my 4Ghz stable results :)

johnsally

09-10-2007, 09:40 PM

how long do you want prime ss to be?

linflas

09-10-2007, 09:53 PM

Q6600 G0 - L727A918 - 3.82Ghz P stable - WC Apogee GT - 1.48v (actual) - ASUS Striker Extreme - by --------linflas

Yes I let prime run longer than what is seen, currently Crunching WCG on it all 4 cores loaded 100% with valid results. (Also playing a little Quake Wars Beta, worth the purchase looks like)

http://img455.imageshack.us/img455/5742/cubefs0.jpg

I would much rather have this stable, but for the life of me cannot get the Striker to co-operate.

http://valid.x86-secret.com/show_oc.php?id=241142

turtletrax

09-10-2007, 10:00 PM

I'll be in on that :cool: I've got 4Ghz stable on my Q6600, but I'm trying to get this now
http://valid.x86-secret.com/show_oc.php?id=241138

It'll pass for about 1 hour then a core craps out on me, while the other 3 soldier on. I'm going to try lapping it and see if that helps tomorrow, if not I'll post my 4Ghz stable results :)

Well we should get this going... PM me if you have thoughts on how we should go about that. Also if you know any Choppers we should get an Avatar started.:cool:

@ Linflas

Dont know allot about the Striker but my EVGA needed me to lower the SPP/MCP links to 4X to get stable at high clocks. Is there any such setting on the Striker?

EDIT: Hey CraptacularOne, have you tried this setting on your EVGA?? If not give it a shot. Even a 3X might get you stable too. That and cranking the HT Voltage were the main things that helped my last MHz.

linflas

09-10-2007, 10:03 PM

@ Linflas

Dont know allot about the Striker but my EVGA needed me to lower the SPP/MCP links to 4X to get stable at high clocks. Is there any such setting on the Striker?

there is, I will have a look at that, thanks for the tip!

Going to let it slide till next week though, have other things I'd rather be doing right now though.

turtletrax

09-10-2007, 10:23 PM

there is, I will have a look at that, thanks for the tip!

Going to let it slide till next week though, have other things I'd rather be doing right now though.

I should also state that there was no noticealbe loss in performance.

CraptacularOne

09-11-2007, 04:11 AM

EDIT: Hey CraptacularOne, have you tried this setting on your EVGA?? If not give it a shot. Even a 3X might get you stable too. That and cranking the HT Voltage were the main things that helped my last MHz.

I haven't tried that yet, but I'll give it a shot this evening :up:

@ johnsally, give me a couple hours of prime and I'll take your word that it's stable :up:

Like I said earlier in this thread, this isn't a bragging rights thread, this thread is meant to help people who are looking for a good stepping to overclock with ;)

linflas

09-11-2007, 04:52 AM

Like I said earlier in this thread, this isn't a bragging rights thread, this thread is meant to help people who are looking for a good stepping to overclock with ;)

I am not sure why you posted this, but if it is reference to the screen shot of 4.1 I posted, my apologies, the first clock I posted is my current 24/7, which is crunching WCG 24/7 100% on all cores as we speak. Giving valid results, about as stable as it gets.

The 4.1 was posted because Turtle had been working on higher clocks, and he is also on a 680i chipset, so I thought I might be able to get a few tips, which he has already been nice enough to add.

did not mean to spam your thread.

no_n|ck

09-11-2007, 06:13 AM

I think that a minimal prime time limit needs to be set, in order to compare our resualts..Its pointless that some folks are posting 15-30min prime shots, while others are realy trying to be 'transparent' with their overclocks, so i vote for minimal 1h of prime95 in order to be on the OC database list..Also separate the Superpi tests as they are useless, regarding stability..

CraptacularOne

09-11-2007, 07:37 AM

I am not sure why you posted this, but if it is reference to the screen shot of 4.1 I posted, my apologies, the first clock I posted is my current 24/7, which is crunching WCG 24/7 100% on all cores as we speak. Giving valid results, about as stable as it gets.

The 4.1 was posted because Turtle had been working on higher clocks, and he is also on a 680i chipset, so I thought I might be able to get a few tips, which he has already been nice enough to add.

did not mean to spam your thread.

No, it wasn't in reference to you or anyone in general :toast: It was made in the hopes that people wont just post BS stable clocks :)

As for the time requirement, as I said before I really have no way of validating that, as anyone can copy and paste whatever they want for times, so it's going to be on the honor system. That's why I ask that we keep things honest :)

sco999

09-11-2007, 07:57 AM

1) Q6600 G0
2) L721A814
3) http://valid.x86-secret.com/show_oc.php?id=241101
4)http://img513.imageshack.us/img513/2986/42062wprime32stableus3.th.jpg (http://img513.imageshack.us/my.php?image=42062wprime32stableus3.jpg)
5) Apogee GTX
6) 1.68v
7) DFI UT P35-2TR
8) Wprime 32m stable

stay tuned for more I am still not done with this one yet, plus I have another chip to test.

turtletrax

09-11-2007, 09:42 AM

Wow CraptacularOne, those are :banana::banana::banana::banana::banana:in' mem freqencies with 4GB. What voltage are you running to them?? I would love that!!

[XC] Synthetickiller

09-11-2007, 10:24 AM

Here's my latest Q6600 OC:

http://i18.tinypic.com/4p9ydfr.jpg

Note: the ram settings should be 5-5-5-15 & DDR2. The stupid CPUZ thinks I have a lot of extra cash to throw around to buy DDR3!

I will be working on getting this prime stable @ 8 hours or more. I don't have time as I need this computer for research atm.

I might be able to lower the voltage a tad, but it seems to require a TON of voltage to stay stable:
cpu: 1.5875v
Dram: 2.3v
NB: 1.55v

Pushing anything past 425x9 blue screens with prime95. I think its due to having ddr2 800 instead of ddr2 1066. I should have dropped a little more chash. Oh well.

This isn't what I was hoping for, but considering some can't even get 3.5ghz stable, I'll take 3.8 stable or maybe a bit lower if I can get much tighter ram timings.

CraptacularOne

09-11-2007, 02:47 PM

List updated :toast:

@ Synthetickiller, I need your FPO batch number to make your result useful to the table :)

@ turtletrax, I'm running 2.4v to them

@ no_n|ck, I have taken your request and separated the Pi results from the main data base :toast:

cliffy

09-11-2007, 03:38 PM

Here's my first entry. I sure i am being seriously held back by the striker extreme at the minute so seriously tempted to get the ASUS Blitz Formula edition. (Any one have any thought on this). Also is it true that i could end up using less voltage to the CPu to get the same clocks??

Anyways

CPU Type : Q6600 G0
Batch : L726A951
Validation : http://valid.x86-secret.com/show_oc.php?id=241481
Cooling : A/C (Thermalright Ultra 120)
Voltage : 1.425
Motherboard : Striker Extrem 1303Bios (1.2V HT = 1.35, NB = 1.45, SB = 1.55 CPU VTT = 1.4)
Screenshot 100% load 3.713Ghz

http://i38.photobucket.com/albums/e107/cliffy2006/3.7prime.jpg

crossg

09-11-2007, 07:34 PM

Pushed my CPU a little higher.
Q6600 G0 L726A850
3852 Mhz Vcore 1.5375v / Actual 1.5040v
CPU-Z Validation : http://valid.x86-secret.com/show_oc.php?id=240078
Stability test (http://www.xtremesystems.org/forums/showpost.php?p=2418682&postcount=1122)

Q6600 G0 - L726A850 - 3.85 Ghz P stable - AC TR Ultra 120 - 1.537v - ASUS P5K Dlx - by --------crossg.

You can just edit my previous 3.8 if you don't mind.;)

Also a 4032 Mhz 32M PI here (http://www.xtremesystems.org/forums/showpost.php?p=2407618&postcount=1036) if you care to add. Same CPU.

CraptacularOne

09-11-2007, 08:28 PM

List updated again :)

FabricioGS

09-11-2007, 09:15 PM

1) G0
2) L723A977
3) http://valid.x86-secret.com/show_oc.php?id=241561
4) http://img384.imageshack.us/img384/607/3600450x8estavelmemos11ri3.th.png (http://img384.imageshack.us/my.php?image=3600450x8estavelmemos11ri3.png)
5) Air Cooler - Coolermaster GeminII + 2x120mm fans
6) 1,4250v bios, 1,4000v real
7) Asus P5K Deluxe + Crucial Balistix PC8500 @ 1125MHz 5-5-4-12

njkid32

09-11-2007, 09:22 PM

Whats your max 100% cpu stress clocks?

FabricioGS

09-11-2007, 09:52 PM

You're asking for me? Haven't tested yet, I'm having some problems with temperature.

NaeKuh

09-11-2007, 10:24 PM

L720B066
1.44Vcore Real
415x9 3.737

http://i125.photobucket.com/albums/p73/aigomorla/3.73ghz.jpg

This is my 24/7 usage.

Board: Asus P5K-DLX
Cooling:
ApogeeGTX
PA120.3
IWAKI RD-30

I think you should honestly only take primes longer then 3 hours. More the better. Quads tend to fail at 2-3 hours during prime, if the voltage is too low. Otherwise i'll pop my 3.825 which failed at 2 hours 30 min @ 1.46Vcore real.

ncsa

09-11-2007, 11:06 PM

Q6600 G0 - L723A924 - 4.41 GHz Wp 1024m stable - Vapochill LS [AC] stock - 1.68v (1.63-4 load) - Abit IP35-Pro stock - OP1000 PSU - by - ncsa

And the meaningless screenshot :) CPUz 498x9 (http://valid.x86-secret.com/show_oc.php?id=240512)

CraptacularOne

09-12-2007, 04:07 AM

rbsmontemor

09-12-2007, 05:53 AM

FabricioGS

09-12-2007, 09:06 AM

I can't add this unless you get me a 4 cores running 100% load. Only 2 cores running does not make it stable ;)

Sorry, I'm still a noob on quad cores :P

Will post later using Prime95, let´s see how far I can get.

CraptacularOne

09-12-2007, 11:31 AM

List updated :toast:

@ Viper.Br, it's OK we we're all newbs at one time ;)

BNDMOD

09-12-2007, 08:56 PM

1) B3
2) L634A700
3) Validation: http://valid.x86-secret.com/show_oc.php?id=241932
4) 3.720Mhz

Prime95
http://img205.imageshack.us/img205/9953/465x9prime95loadzt2.th.jpg (http://img205.imageshack.us/my.php?image=465x9prime95loadzt2.jpg)

no_n|ck

09-13-2007, 02:22 AM

CraptacularOne

09-13-2007, 04:14 AM

Ic3man

09-13-2007, 04:36 AM

CPU : Q6600 G0
Week : L23B010
Clockspeed : 423x9 = 3.807 ghz
Cooling : D-Tek fuzion
Vcore : 1.52
Motherboard : Asus Blitz Formula

http://valid.x86-secret.com/show_oc.php?id=242033

12 hours Prime 95 small fft's stable.

http://img.photobucket.com/albums/v608/webbo10/3800final.jpg

911us

09-14-2007, 12:18 PM

got my Q6600 L723A924 today,will test and report soon

GripS

09-14-2007, 01:28 PM

dpa

09-14-2007, 10:32 PM

CPU : QX6850 G0
Week : L724
Clockspeed : 4xxx12 = 4.8Ghz+++
Cooling : Solid Copper pot + Dryice
Vcore : 1.8v idle = 1.68v max load in 06 cpu test WITH vdrop and vcore mod
Motherboard : Asus P5K, bought P5K-E today, will test it..

Pi time is bad because of crappy memory timings; 5-5-5-15. Cpu test in 06 is low because of 6100GFX card, got 7400 with 8800Ultra when setting was 4.79Ghz.

Ic3man

09-14-2007, 11:19 PM

God damn!!!! Sweet......very sweet. That is one hell of a chip you got there. You plan on running that 24/7??

Yeah. Its well within the comfort zone (temps/vcore) for me.:D

vkostas

09-14-2007, 11:23 PM

Wee 1st post in the forums after a long time of lurking :)

Here is my little Q6600. Hoping for better O/C a bit later with a new mobo
and maybe some better ambient temps :)

CPU: Q6600 G0
FPO #: L719B278
Validation: http://valid.x86-secret.com/show_oc.php?id=242740
Cooling: D-Tek Fuzion / Laing D5(Setting 3) / Back Ice GTX 480 - Ambient Room temps : 26 - 30 C
M/B: Abit IP35-Pro
Vcore: 1.6050 Set in BIOS 1.49 - 1.50 Real under load.... this board realy droops :S hope the new P5K Premium will not :)

http://img508.imageshack.us/img508/6214/untitled3qv5.th.jpg (http://img508.imageshack.us/my.php?image=untitled3qv5.jpg)

dzeuk_ph

09-14-2007, 11:48 PM

High Guys!

How about max. FSB for these quads? how high can they go?

thanks!

largon

09-14-2007, 11:59 PM

Q6600 G0 - L724A786 - 3.6Ghz P stable - WC D-Tek Fuzion - 1.396v - abit IP35 Pro - by --------largon

Q6600 G0 - L724A786 - 3.6Ghz P stable - WC D-Tek Fuzion - 1.396v - abit IP35 Pro - by --------largon

http://img80.imageshack.us/img80/6633/l724a7861q66003600mhz8hzv6.th.jpg (http://img80.imageshack.us/img80/6633/l724a7861q66003600mhz8hzv6.jpg)

Cordovader

09-15-2007, 12:57 AM

1) QX6850 G0
2) L723A658
3) http://valid.x86-secret.com/show_oc.php?id=242768
5) Thermalright Ultra 120 eXtreme
6) 1,3625v in bios, 1,336v idle, 1,328v full load
7) Asus Blitz Formula

4)
http://img207.imageshack.us/img207/397/1hlargefft36ghz1328vuk2.th.jpg (http://img207.imageshack.us/my.php?image=1hlargefft36ghz1328vuk2.jpg)

And some non daily oc :)

Air
http://img264.imageshack.us/img264/2779/1m425ghz158vwf9.th.jpg (http://img264.imageshack.us/my.php?image=1m425ghz158vwf9.jpg)http://img264.imageshack.us/img264/5382/0541ghzrr2.th.jpg (http://img264.imageshack.us/my.php?image=0541ghzrr2.jpg)http://img396.imageshack.us/img396/4363/01415ghzak2.th.jpg (http://img396.imageshack.us/my.php?image=01415ghzak2.jpg)

LN2
http://img396.imageshack.us/img396/9713/05resoluciondeescritorifv4.th.jpg (http://img396.imageshack.us/my.php?image=05resoluciondeescritorifv4.jpg)http://img184.imageshack.us/img184/8631/spi2customub4.th.jpg (http://img184.imageshack.us/my.php?image=spi2customub4.jpg)

sam95ta

09-15-2007, 03:21 PM

Q6600 GO @ 3.77
L726A849
http://valid.x86-secret.com/show_oc.php?id=243080
P5K E ( pencil mod)
Noctua NH U 12
1.50 bios 1.48 actual

I just switched over from P5B deluxe.Here is my first try with this board.Will try to lower vcore.

CraptacularOne

09-15-2007, 05:47 PM

List updated :toast:

@ dpa, that is one hefty result, but I'm going to need a stable shot of it running prime for at least an hour or at the very least a quad instance of Pi 32m :)

@ vkostas, welcome aboard :)

dragonhunter

09-15-2007, 06:40 PM

1) Q6600 G0
2) L727A658
3) COOLER MASTER GeminII
4) 1,5675v in bios
7) Abit IP35-E

http://img502.imageshack.us/img502/4340/355ghz15475vcorebm8.jpg (http://imageshack.us)

CraptacularOne

09-15-2007, 07:17 PM

Gotcha dragonhunter :up:

RLM

09-15-2007, 09:41 PM

L723B284

CPU : Q6600 G0
Week : L23B284
Clockspeed : 434x9 = 3.908 ghz
Cooling : Apogee GT (Bowed)
Vcore : 1.52
Motherboard : DFI P35-T2R

http://img234.imageshack.us/img234/7338/largeftt2nr9.jpg

RLM

turtletrax

09-15-2007, 10:17 PM

Any more thoughts on a 4Ghz Quad club?

dzeuk_ph

09-15-2007, 11:08 PM

So anyone tried max. fsb?

aspms*

09-16-2007, 01:45 AM

So anyone tried max. fsb?
There is already another thread for this type of statistic: http://www.xtremesystems.org/forums/showthread.php?t=157946

Luis_GT

09-16-2007, 08:30 AM

1) QX6700, B3
2) L639A615
3) http://valid.x86-secret.com/show_oc.php?id=243386
4) http://i16.photobucket.com/albums/b29/Luis_GT/th_daylyclock.jpg (http://i16.photobucket.com/albums/b29/Luis_GT/daylyclock.jpg)
5) Water cooled (Thermaltake block)
6) 1.48 bios, 1.39-1.4 real
7) Asus P5W DH Deluxe

Hope you don't mind me using SMP as a stability tester... don't feel like shutting it down.

CraptacularOne

09-16-2007, 09:49 AM

Hey Luis nice to have you aboard, but can you please get me a shot of it running prime? :toast:

Luis_GT

09-16-2007, 10:21 AM

I'll do SPI32M... If I get some time, I'll do a Prime 95 run.

CraptacularOne

09-16-2007, 11:16 AM

I'll do SPI32M... If I get some time, I'll do a Prime 95 run.

Prime is preferable, and if you choose Pi 32m, I'm going to need a quad instance :toast:

Luis_GT

09-16-2007, 11:21 AM

Ok, so 2-8 hours of prime is enogh right?

as soon as my HDD backup finishes, I'll start it. :up:

dj883u2

09-16-2007, 01:27 PM

My Q6600....

Q6600 G0 | L725B057 | 3608mhz | 1.352V | Liquid |

http://img75.imageshack.us/img75/4451/38514368fu9.th.jpg (http://img75.imageshack.us/my.php?image=38514368fu9.jpg)

http://img169.imageshack.us/img169/2391/64945578ia7.th.jpg (http://img169.imageshack.us/my.php?image=64945578ia7.jpg)

Q6600 G0 | L725B057 | 3708mhz | 1.40V | Liquid |

http://img241.imageshack.us/img241/7949/q6600prime95140vnk5.th.jpg (http://img241.imageshack.us/my.php?image=q6600prime95140vnk5.jpg)

http://img411.imageshack.us/img411/613/q6600prime95140vzm8.th.jpg (http://img411.imageshack.us/my.php?image=q6600prime95140vzm8.jpg)

1) G0
2) L725B057
3) Water - D-Tek Fuzion
4) 1.352V@3.608Mhz - 1.40V@3.708Mhz
5) Asus P5K-E

By;)

CraptacularOne

09-16-2007, 08:18 PM

Ok, so 2-8 hours of prime is enogh right?

as soon as my HDD backup finishes, I'll start it. :up:

That will be fine :)

List up dated again :toast:

largon

09-17-2007, 01:22 AM

Err...
I seem to have typed in an incorrect week-code for my CPU.
Please fix: "L727A786" to "L724A786". :)

RLM

09-17-2007, 01:56 AM

My entry post #170 seems to be missing from your update.

If there's a problem with it please let me know.

RLM

linflas

09-17-2007, 02:46 AM

@ craptacularone,

Need you to adjust the stable vcore on my entry, was getting errors on one type of workunit in WCG, the other 3 were fine, adjusted the vcore a bit and loosened some secondary memory timings, and all is well again.

Please adjust the 1.48 I had posted earlier to 1.52, thanks.

Also, don't know if it was mentioned before, but shouldn't the VID of each chip be listed as well?

CraptacularOne

09-17-2007, 07:18 AM

List updated, errors fixed :toast:

CraptacularOne

09-17-2007, 08:19 AM

list re-ordered to reflect voltages needed for clock speed attained aswell :)

Luis_GT

09-17-2007, 08:28 AM

1) QX6700, B3
2) L639A615
3) http://valid.x86-secret.com/show_oc.php?id=243713
4) http://i16.photobucket.com/albums/b29/Luis_GT/th_Prime.jpg (http://i16.photobucket.com/albums/b29/Luis_GT/Prime.jpg)
5) Water cooled (Thermaltake block)
6) 1.52 bios, 1.408 real
7) Asus P5W DH Deluxe

here we go, as you can see, its nice and crispy... I'm glad I ordered a Apogee GT... this Thermaltake could barely keep up with my old E6600 :shakes: Most likely it'll do better once I get the new block.

timber715

09-17-2007, 09:21 AM

Q6600 L727A673 G0
air cooled: Tuniq tower 120
1.375V bios
asus p5k-deluxe wifi
temps 38 - 67C

http://i159.photobucket.com/albums/t130/timber715/3400stable.jpg

EXPANDER

09-17-2007, 10:24 AM

q6600 go. bios 1.19v, Low voltage with, core 3040 mhz

http://www.resimekle.gen.tr/imagehosting/images/rIl53400.jpg

CraptacularOne

09-17-2007, 12:10 PM

List Updated :toast:

@ Luis_GT damn dude! you can keep your house warm with those temps!

@ EXPANDER, I'm going to need more info than that to make use of your result. Give me the week, a shot of it running Prime @100% load (all 4 cores), cooling used, and motherboard.

dj883u2

09-17-2007, 12:24 PM

Q6600 G0 | L725B057 | 3808mhz | 1.456V | Liquid |

http://img230.imageshack.us/img230/9297/q6600prime951456vmw5.th.jpg (http://img230.imageshack.us/my.php?image=q6600prime951456vmw5.jpg)

http://img215.imageshack.us/img215/8778/q6600prime951456vxv0.th.jpg (http://img215.imageshack.us/my.php?image=q6600prime951456vxv0.jpg)

1) G0
2) L725B057
3) Water - D-Tek Fuzion
4) 1.456V
5) Asus P5K-E

By;)

Luis_GT

09-17-2007, 12:25 PM

... why would I want to warm up my house... I'm constantly turning my A/C on...

Sad thing, My water temp doesn't break 30c

CraptacularOne

09-17-2007, 12:38 PM

... why would I want to warm up my house... I'm constantly turning my A/C on...

Sad thing, My water temp doesn't break 30c

It was a joke.....you know "haha funny"?....:shrug:

And if your water temps are getting that high, it's almost definitely because of a poor block that's not transferring heat from the CPU.

@ dj883u2, updated your result :)

Luis_GT

09-17-2007, 12:59 PM

It was a joke.....you know "haha funny"?....:shrug:

And if your water temps are getting that high, it's almost definitely because of a poor block that's not transferring heat from the CPU.

@ dj883u2, updated your result :)

I know it was a joke... I was just saying that my house can't get any hotter... :rofl:

Anyways... Apogee has been shipped... Soon I'll post an updated OC... one that doesn't reach 81C :p:

EXPANDER

09-17-2007, 01:11 PM

L719 GO, Q6600 1.19 Vcore 3040 mhz -60C phase change
SAPPHIRE HD2600XT GDR4
DFI RD600 UT ICFX 3200
2X 512 MB MUSHKIN DDR2 800 MHZ 4-4-3-10 2T - 1,8 V
ASUS 360 WATT PSU
WD 250 GB HDD

1.19 Vcore 3040 mhz

http://www.resimekle.gen.tr/imagehosting/images/rIl53400.jpg

Default 2.4 GHZ 1 Vcore:)

http://www.resimekle.gen.tr/imagehosting/images/gtU63985.jpg

CraptacularOne

09-17-2007, 01:45 PM

@ EXPANDER, ahem, please I need the full FPO batch # if you've got it and I cannot add your result until you post a screen shot of it running at 100% load on all four cores. Booting into window means nothing, I can boot my CPU into windows at 4.2Ghz and open CPU-Z but it fails instantly in Prime95. So those screens are of no use to me :shrug:

dj883u2

09-17-2007, 02:01 PM

crossg

09-17-2007, 06:01 PM

@ craptacularone,
Also, don't know if it was mentioned before, but shouldn't the VID of each chip be listed as well?
That would be a lot of work for craptacularone but it would make it a more complete data base.:up:

CraptacularOne

09-17-2007, 06:27 PM

That would be a lot of work for craptacularone but it would make it a more complete data base.:up:

Not only that, we'd have to get everyone who's submitted a result to post their VID. The list is fine as it is and is giving a real good indication of what voltage is needed to get speeds stable as well as what steppings are doing what. And the more people post their results, the more complete it will become. :)

BNDMOD

09-17-2007, 07:22 PM

1) B3
2) L634A700
3) Validation @ 4.1Ghz - http://valid.x86-secret.com/show_oc.php?id=242169
4) 3.720Mhz

WPrime
In progress
http://img453.imageshack.us/img453/2652/3720mhzprimestablewn3.th.jpg (http://img453.imageshack.us/my.php?image=3720mhzprimestablewn3.jpg)

TesT Done
http://img223.imageshack.us/img223/9879/3720mhzprimestable1ym6.th.jpg (http://img223.imageshack.us/my.php?image=3720mhzprimestable1ym6.jpg)

911us

09-17-2007, 09:17 PM

@BND|MOD : very nice B3 chip you got,later week B3 (***F***) can't compare. What 's your 24/7 speed ?

BNDMOD

09-17-2007, 09:25 PM

@BND|MOD : very nice B3 chip you got,later week B3 (***F***) can't compare. What 's your 24/7 speed ?My 24/7 is 3.0Ghz, only to has my vga free :) fonr any botlle neck....
Q6600 @ 3.0Ghz - 1.2Vcore

dj883u2

09-18-2007, 12:25 PM

Q6600 G0 | L725B057 | 3906mhz | 1.496V | Liquid |

http://img230.imageshack.us/img230/8530/58821105op4.th.jpg (http://img230.imageshack.us/my.php?image=58821105op4.jpg)

1) G0
2) L725B057
3) Water - D-Tek Fuzion
4) 1.496V
5) Asus P5K-E

By;)

timber715

09-18-2007, 05:07 PM

CraptacularOne,
would this qualify? same chip Q6600 L727A673 G0
air cooled: Tuniq tower 120
1.387V bios
asus p5k-deluxe wifi

http://i159.photobucket.com/albums/t130/timber715/3600spi32m.jpg

CraptacularOne

09-18-2007, 05:24 PM

List updated :toast:

@ BND|MOD, I'm going to need your voltage for that run to make it usefull :)

@ timber715, I'm going to need at the least a quad instance of 32m Pi :)

BNDMOD

09-18-2007, 05:29 PM

List updated :toast:
@ BND|MOD, I'm going to need your voltage for that run to make it usefull :) @ 1.55vcore in BIOS thanks

CraptacularOne

09-18-2007, 07:39 PM

@ 1.55vcore in BIOS thanks

Done :)

BNDMOD

09-18-2007, 08:09 PM

Sorry other update

1) B3
2) L634A700
3) Validation @ 4.1Ghz - http://valid.x86-secret.com/show_oc.php?id=242169
4) 433 x 9 @ 3.9Ghz @ 1.58volts in BIOS

SP32M X 4
In progress
http://img222.imageshack.us/img222/7894/433x9spm32x41vo3.th.jpg (http://img222.imageshack.us/my.php?image=433x9spm32x41vo3.jpg) http://img220.imageshack.us/img220/9646/433x9spm32x42kv6.th.jpg (http://img220.imageshack.us/my.php?image=433x9spm32x42kv6.jpg)

Finshed
http://img146.imageshack.us/img146/7025/433x9spm32x43yo4.th.jpg (http://img146.imageshack.us/my.php?image=433x9spm32x43yo4.jpg)

timber715

09-19-2007, 12:58 AM

will try to run one later perhaps, i just want to thank you for the work you do for the community... Cheers...

dj883u2

09-19-2007, 08:28 AM

Sorry, but to the frequency of 3906Mhz The prosessor is stable with 1.48V, end not 1.496V.

Q6600 G0 | L725B057 | 3906mhz | 1.48V | Liquid |

http://img216.imageshack.us/img216/5778/q6600prime95148vhw4.th.jpg (http://img216.imageshack.us/my.php?image=q6600prime95148vhw4.jpg)

1) G0
2) L725B057
3) Water - D-Tek Fuzion
4) 1.48V
5) Asus P5K-E

By:up:

GameGuru

09-19-2007, 09:42 AM

Can some of you guys post some of your other settings please such as NB, SB, ICH etc... I'm just wonder on average what your cranking those up to as well. I just starting priming 3.6 @ 1.35v but 3hrs into Prime one of the cores failed. Any help is appreciated, thanks!

largon

09-19-2007, 11:39 AM

Sorry, but to the frequency of 3906Mhz The prosessor is stable with 1.48V, end not 1.496V.
(...)Priming for 20mins does not qualify as stable.

And what's the real vCore? Or the BIOS setting?

no_n|ck

09-19-2007, 01:23 PM

Priming for 20mins does not qualify as stable.

And what's the real vCore? Or the BIOS setting?

agree! whats the deal with those 20min shots, BS!
if u would like to post something provable, at least make 1-2h prime shot!

GameGuru

09-19-2007, 01:40 PM

agree! whats the deal with those 20min shots, BS!
if u would like to post something provable, at least make 1-2h prime shot!

And to be honest a 2hr prime is NOT stable, I can back this because last night I was priming and at 2hrs and 45min one of my cores failed.

Quick question. What are you guys using for priming, Large, small or blend?

Thanks

timber715

09-19-2007, 01:58 PM

And to be honest a 2hr prime is NOT stable, I can back this because last night I was priming and at 2hrs and 45min one of my cores failed.

Quick question. What are you guys using for priming, Large, small or blend?

Thanks

i agree, trying to lower my Vcore a while ago and one core failed after 2hrs...:shrug: after an hour though, i felt it was gonna be alright...:yepp:
priming with small ffts
oh well, back to it again...

RLM

09-19-2007, 02:27 PM

What I have to say next is not really an educated opinion, but solely based on my experience.

With the x2s and duo cores I used to run 8+ hour prime and orthos runs.

Over the last year with quads, I haven't really bothered.

If it fails after a few minutes, I'll make adjustments and try again. If it then runs for 30 minutes or so that's good enough for me.

I use my kit for a lot of 3d rendering, using a renderer called fprime. Fprime is an interactive renderer that let's you adjust scenes whilst they're rendering. It pushes the cores to the max, more so than other renderers, and is a pretty good indication of stability.

In addition to this I do a lot of photoshop work on large files, and also play games.

With all of that, my kit certainly up to this point has been more than stable.

So for me personally, hours of priming is just overkill.

As I say this is just my experience.

RLM

crossg

09-19-2007, 02:48 PM

You know I appreciate that CraptacularOne has gone to the effort to start and constantly update this thread, People are always demanding 8 or 24 hour stability tests. Thread title says "Quad core OC Data base"? I find the info valuable, Chip batches/stepping that clock high, what kind of voltage is required for a given FSB. I myself have submittted under 3 hour primes and if that gives someone doubt then thats fine with me but someone may make use of the information I or others submitted. I don't OC 24/7 but I test quite a bit and maybe there are others out there that do the same as myself. I have run prime a few time for extended hous and had it fail because I was dicking around in the background when I shouldn't have been. What a waste of time.:rolleyes: Yeah I don't think 10 0r 20 minites is a good indicator of stabilty but 1 to 2 hours should be a good indicator of the chips capabilities. Sorry just my 2 cents:) .

largon

09-19-2007, 03:16 PM

This thread is completely useless if everyone's inventing their own definions for stability. For years the term "prime stable" has stood for 6-24h of continuous, high priority stress. Now it's just a quick 20min session that is infact less stressing than a quad instance 32M SPi?

I guess the OP should had worded the conditions more unamous than what he did:

4) Screen shot of it running at that speed (orthos, prime95..ect) 100% load
(...)

I will accept a quad Pi 32m run (4 instances of 32m Pi) as well but please stable OCs only
(...)

P = Prime stable
32m = Pi 32m stable
Wp = Wprime stable

GripS

09-19-2007, 03:46 PM

This thread is completely useless if everyone's inventing their own definions for stability. For years the term "prime stable" has stood for 6-24h of continuous, high priority stress. Now it's just a quick 20min session that is infact less stressing than a quad instance 32M SPi?

I guess the OP should had worded the conditions more unamous than what he did:

I agree. I have seen quite a few posts lately where people even :banana::banana::banana::banana::banana: that we ask for proof of stability and some even put you down and insult you for asking for a prime stable screenshot.

YES prime95 IS the standard for measuring stability. It has been for years and will continue to be(for me anyway).

crossg

09-19-2007, 04:24 PM

O/T. @Largon & GripS. Wasn't my intent to :banana::banana::banana::banana: on anyone nor is it my intent to hyjack the thread.;) Honestly I have had bad Q6600 G0's that would fail well before (in a matter of minutes) most of the clocks seen here. I have a good one now and can reference this thread for info which is useful to me. It is pretty simple to open up an new thread saying ("Post your 8 hour Prime small FFT's quad results here.") Anyways nuff said and no offence I hope.:)

Ace-a-Rue

09-19-2007, 05:40 PM

oh man!...prime fanatics at it again...stability is what the user does with his or her system and there are no freezes, no BSOD, no random reboots, play games without dropping back to the desktop, etc.

there might be only one program that stresses the computer and that is "Folding"...the user might want to test his overclocked computer with prime 95 before beginning to fold...then, it makes sense to run P95 for 24, 36 or 48 hours to make sure he can hack folding with an overclock computer.

i don't think it is in any book which says you have to show 8 hours of prime to make it a valid overclock!...if you do 1, 2 or 8 hours, what does that prove?!...to me, it says you hacked 1, 2 or 8 hours of prime...grrr-eat!:D

nugzo

09-19-2007, 05:57 PM

Q6600 L724A 1.54v 3825mhz (425 x 9)
Asus Striker Extreme 1303 bios
D-tek Fuzion

http://img458.imageshack.us/img458/4051/3825fn4.jpg

http://img187.imageshack.us/img187/5340/38251za3.jpg

CraptacularOne

09-19-2007, 06:44 PM

List updated :toast:

And guys if you want to argue please take it elsewhere. :down: If you don't like the list then move on, no need to thread crap. If you think the list is useless, then you don't need to post here, and trust me you aren't wanted here anyway. This thread is about seeing what steppings are getting to what overclocks. Go make your own thread if you don't like the way I'm running this one.

I swear, I don't know why I bother sometimes. This reminds me of my other thread where I showed everyone that the quad core fix was for real and posted validations of the new EVGA board and their new found FSB ability with quads, and some people couldn't resist but the call it BS, useless, or blurry pics, and having no value. Why don't you people do something useful instead of constantly whining?

nugzo

09-19-2007, 07:06 PM

CraptacularOne

09-19-2007, 07:15 PM

Your doing a great job.

btw, you removed my other database entry. This recent one is a different CPU and motherboard.

Thanks :) And fixed, I though it was the same chip :shrug:

DJSUB

09-20-2007, 05:23 AM

here's mine :D

highest fsb :
cpuz validation : http://valid.x86-secret.com/show_oc.php?id=244367

http://valid.x86-secret.com/ccpuz.php?id=244367

highest on 9x multi (aircooling) :

http://img231.imageshack.us/img231/7105/1mwatermarkkh0.png

cpuz validation : http://valid.x86-secret.com/show_oc.php?id=244389

tnx :)

ocZZZ

09-20-2007, 05:50 AM

I like that logo djsub

CraptacularOne

09-20-2007, 08:13 AM

@ DJSUB, That's great but a single 1m Pi run is no where near stable :rolleyes: If you want to be added to the list please refer to the opening post in this thread and give me the details :toast:

badboy

09-20-2007, 05:27 PM

1)GO
2)L721A814
3)Apogee GT
4)http://valid.x86-secret.com/show_oc.php?id=244974
5) Asus P5K3 Deluxe
6)3.6ghz(450x8)@1.54v
http://img229.imageshack.us/img229/1637/stableoverclockxw1.th.jpg (http://img229.imageshack.us/my.php?image=stableoverclockxw1.jpg)

Ace-a-Rue

09-20-2007, 05:55 PM

OK I would like to start a Quad Core Database so we can all post and see what steppings are doing what. All quads are welcome and I will have individual categories for each model. So post up and lets do something useful :)

So here's the deal, give me....
1) Post your CPU model & Core revision (B3 or G0) Q6600 "G0"
2) Week (L726A...ect) L720B066
3) CPU-Z Validation CPUZ in image
4) Screen shot of it running at that speed (orthos, prime95..ect) 100% load (below)
5) Cooling being used dual fan TRUE 120
6) Voltage 1.5v
7) Motherboard used (this is optional but helpful just the same:)) Abit IP35 Pro

some answers in your above quote...

proof below

Luis_GT

09-21-2007, 09:08 AM

1) QX6700, B3
2) L639A615
3) http://valid.x86-secret.com/show_oc.php?id=245216
4) http://i16.photobucket.com/albums/b29/Luis_GT/th_prime-1.jpg (http://i16.photobucket.com/albums/b29/Luis_GT/prime-1.jpg)
5) Water cooled (Apogee GT)
6) 1.41 bios, 1.408 real
7) Asus P5W DH Deluxe (vdroop modded)

Update on my OC. Seems like my CPU's temp sensor is fubar. :down:

Intern

09-22-2007, 05:16 PM

1) QX6700ES, B3
2) Engineer Sample
3) http://valid.x86-secret.com/show_oc.php?id=221104 (http://valid.x86-secret.com/show_oc.php?id=221104)
4) Adding soon
5) Water (Apogee GTX)
6) 1.52
7) P5K Deluxe

CraptacularOne

09-22-2007, 05:59 PM

Luis_GT

09-22-2007, 07:43 PM

List updated :toast: Sorry for the delay I had a massive amount of work to catch up on recently.

@ Luis_GT If you are still using that crappy thermaltake pump and rad, having the best block in the world won't save you. You need to get a good rad and a high volume high head pressure pump. Getting the better block was only the first of the 3 step process you need to take to cure yourself of the "thermalbake" syndrome ;)

I'm using a 180GPH summergible pump... and thats the problem, ironically, also I have a Swiftech M220 rad before the CPU and the thermaltake rad after the CPU... I just put in my old 90lph thermaltake pump and its working better... F@H is about 5C+ cooler than with the summergible pump...

I also swithc my lines from 1/4" to 3/8"

dertimaushh

09-23-2007, 01:13 AM

Got a new (pretested) one:

Q6600 L727A673 G0

With Water 3807Mhz @ 1,44V

http://img209.imageshack.us/img209/4311/3800144tj1.th.jpg (http://img209.imageshack.us/my.php?image=3800144tj1.jpg)

With Air 3807Mhz @ 1,472V

http://img209.imageshack.us/img209/3571/38071472v15stddg4.jpg (http://imageshack.us)

For 3600Mhz i need 1,34V on water and 1,372V on air.

Q6600 G0 - L727A673 - 3,8Ghz P stable - AC TR Ultra eXtreme - 1.472v - Gigabtye P35-DQ6 - by --------------dertimaushh

Maybe 3900Mhz will be possible with X38-DQ6 and TR IFX14 next week.

Edit: In the Speedfan Temps the +15C (difference to Core Temp) are also included.

Greetz

Tim

CikaNovo

09-24-2007, 04:21 AM

Here's mine:

1) Q6600 G0, 3.6Ghz at 1.4125 vCore
2) batch 720B080,
3) EVGA 680i mobo
4) Ultra 120 eXtreme

24 hours Prime stable

http://i231.photobucket.com/albums/ee146/cikanovo/3.6Ghz24hoursPrimestable.jpg

Ic3man

09-26-2007, 04:36 AM

**UPDATE**

CPU : Q6600 G0
Week : L23B010
Clockspeed : 500x8 = 4 ghz
Cooling : D-Tek fuzion
Vcore : 1.62
Motherboard : Asus Blitz Formula

http://valid.x86-secret.com/show_oc.php?id=247191

http://img.photobucket.com/albums/v608/webbo10/quad.jpg

*edit - failed after 7hours :(

no_n|ck

09-26-2007, 04:43 AM

iceman, thats awsome FSB for quad, and a great OC...what are the ambs temp, as i see u got ur cores at 55°C...mine is hitting 70°C on cores with 1.62 at 21°C amb temp on PA120.3, dual DDC3.2, D-Tek Fuzion...

Ic3man

09-26-2007, 04:45 AM

Chilly m8. 18c in the study atm.

CraptacularOne

09-26-2007, 10:08 AM

Sorry for the delay in getting the results added, work has been very hectic :( I will update the list this evening when I get home. Keep posting, guys, and nice job on the OC's.

sobol

09-26-2007, 10:54 AM

Hi CraptacularOne

Can you please update my entry for my second Quad.
This time it's a maximum stable on reasonable voltage:

It is 3.7 Ghz 1.5V, strange is that I had to up the South Bridge voltage to 1.2v otherwise it was always failing after 1h20m.

1) Q6600 G0
2) L724A900 Pack Date: 08/28/2007
3) Screen shot below
4) Screen shot below of Super PI - SMALL FFT
5) ThermalRight 120 Ultra Extreme + MOUNTING MOD + LAPPING + S-FLEX SFF21E
6) 1.450v bios, 1.432v windows
7) Asus P5K Deluxe, Bios 0404

http://img178.imageshack.us/img178/2554/3700150vbiosxpastelesspvj4.jpg
http://img413.imageshack.us/img413/6792/3700150vbiosxpastelesspqa1.jpg

drynyks

09-26-2007, 11:13 AM

You can update mine if you would. Once I get more heat out of my loop I know this thing can do 3.8. I am bowing my block and putting in a new nozzle next week so that should get me there. I had 3 comps in this room heating it up so ambient was probably close to 27-30c. For now though here is the latest.

This reminds me of my other thread where I showed everyone that the quad core fix was for real

BTW what fix?

http://home.comcast.net/~drynyks/3708-12368hr.jpg

CraptacularOne

09-26-2007, 01:51 PM

List updated :toast:

@ drynyks, when the original 680i boards were introduced, they could not overclock quad cores much past 300Mhz FSB. EVGA was the first to do a revision to the board to "fix" the limitation. I was a tester for the new "fixed" boards and was the first one to give anyone proof that the fix was working and in fact it works pretty good.

This is the thread I was talking about:
http://www.xtremesystems.org/forums/showthread.php?t=135093

Ch0p5t1ckB01

09-26-2007, 09:30 PM

Please add me to the list :D

Q6600 G0 stepping
L723A978
http://valid.x86-secret.com/show_oc.php?id=247484
Thermalright Ultra 120 eXtreme with S-Flex 1600RPM/63 CFM/28 dB
Bios @ 1.4500v, Idle @ 1.408v, Load @ 1.344v
Gigabyte P35-DS3R rev.1

My OC is 8 hours Orthos Stable, but don't have a screenshot of that, I'll upload the new image after I redo the test.
Core temp is @ bottom right corner, it reads 59,59,62,62.

http://img340.imageshack.us/img340/3849/3440mhzocmo9.th.jpg (http://img340.imageshack.us/my.php?image=3440mhzocmo9.jpg)
http://img181.imageshack.us/img181/2228/cpuzvalidationzn7.th.jpg (http://img181.imageshack.us/my.php?image=cpuzvalidationzn7.jpg)

EDIT: SP2004 is reporting that Q6600 is @ 3.86Ghz... I don't know why, but that's not my OC (I WISH IT WAS)

CraptacularOne

09-27-2007, 06:04 AM

Gotcha Ch0p5t1ckB01 :up: And the reason it's reporting the wrong speed is because you didn't use the stock multi. It's just a bug, in that app ;)

holwill

09-27-2007, 08:47 AM

8hrs P95 v25.3 small fft's stable.

http://www.r5jones.aquiss.com/Pictures/P95%20Stable.jpg

Q6600@3.6 400x9 1.425vcore
Revision: GO
Batch: L724A828
Asus P5K-Premium 0204 Bios
Temps: 60/60/54/54
Cooling: Custom Water D-Tek Fusion,Pa120.2+Pa120.1,D5

Ch0p5t1ckB01

09-27-2007, 07:34 PM

Q6600 currently Priming @ 3.6Ghz with 1.456v. Getting some massive vDroop from P35-DS3R but this is to be expected from this board. 1.575v set in bios, 1.508v while idle, and 1.456-1.488v during load. I'll get validation and post screens once I have it SP stable. :D

EDIT:
Hey CraptacularOne, could you please update my OC on the list?

Q6600 G0 stepping
L723A978
http://valid.x86-secret.com/show_oc.php?id=247909
Thermalright Ultra 120 eXtreme with S-Flex 1600RPM/63 CFM/28 dB
Bios @ 1.575v, Idle @ 1.508v, Load @ 1.456v
Gigabyte P35-DS3R rev.1 F6 Bios

EDIT: New screenshot of Q6600 @ 3.6Ghz, 10 hours SP Stable!
http://img208.imageshack.us/img208/4282/3600mhzocwc7.th.jpg (http://img208.imageshack.us/my.php?image=3600mhzocwc7.jpg)
http://img522.imageshack.us/img522/1183/cpuzvalidationvw9.th.jpg (http://img522.imageshack.us/my.php?image=cpuzvalidationvw9.jpg)

Ic3man

09-27-2007, 10:50 PM

**UPDATE**
Since my last clock failed after 7 hours I thought I'd better post an update, upped the fsb by 1 for a bit of clarity too so now at 501x8 = 4009mhz 8 hrs stable and counting ;)

http://valid.x86-secret.com/show_oc.php?id=247940

CPU : Q6600 G0
Week : L23B010
Clockspeed : 501x8 = 4009mhz
Cooling : D-Tek fuzion
Vcore : 1.64
Motherboard : Asus Blitz Formula

http://img.photobucket.com/albums/v608/webbo10/4gigq6600.jpg

ThePrutser

09-27-2007, 11:55 PM

sesdave

10-01-2007, 12:24 PM

1) Q6600 G0
2) L727A963
3) CPU-Z Validation
4) Screenshot (http://www.wasvu2.nl/images/stories/oc/Prime95%20-%2013Hours.jpg) of it running @ 3.6Ghz 13 Hours prime95 100% load
5) TR Ultra 120 Extreme (Lapped)
6) 1.4625
7) P5K-E WIFI/AP

P.S.
It is my first OC ever :D

Nice - Does it show same temps with coretemp 95.4 beta? I idle 36c but run 70c load on core0/1. Makes me think of lapping the CPU if you can get that low. You haven't got your PC in a fridge have you-lol!

CraptacularOne

10-01-2007, 12:32 PM

list updated :toast:

Ch0p5t1ckB01

10-01-2007, 07:12 PM

I'm still listed as 3.44Ghz....:confused:

I'm 3.6ghz stable...

CraptacularOne

10-01-2007, 07:21 PM

I'm still listed as 3.44Ghz....:confused:

I'm 3.6ghz stable...

Fixed :up:

Ch0p5t1ckB01

10-01-2007, 09:45 PM

SWEET! THANKS!!:up:

jagt

10-02-2007, 04:56 AM

Picked up a G0 Q6600 today. L727B248... Any idea what I could expect of it? I'm not gonna bother trying it in my P5W. Waiting 'till the rest of the X38 boards are out. Will probably end up with a P5E or a Maximus Formula.

ThePrutser

10-02-2007, 06:36 AM

If it is even possible to make an estimate...

When I compare your CPU's FPO to the FPO's listed in OC Database, it seems like you have a CPU from a pretty new batch. So according to me it is pretty hard to make any estimate about what to expect. :shrug:

Plug it in, and go :D

But statistics and estimates never have been my best subject, and I am pretty new to overclocking. So my opinion is probably worthless :p:

CraptacularOne

10-02-2007, 08:47 AM

Zucker2k

10-02-2007, 05:56 PM

I was playing with my Q6600 this evening and got this...

Q6600 GO @ 4050 Ghz
L726A820
Thermaltake BigWater 745 (yes I know, crappy water cooling kit)
1.625 bios set, 1.6 idle, 1.617 load
Asus P5B Deluxe bios 1216.

CraptacularOne

10-02-2007, 06:28 PM

@ Zucker2k, that's nice but you are going to need at the very least a quad instance of 32m Pi if you want to get on the list.

Zucker2k

10-02-2007, 07:36 PM

@ Zucker2k, that's nice but you are going to need at the very least a quad instance of 32m Pi if you want to get on the list.

You need to see FOUR instances of 32m Pi? :confused:

virtualrain

10-02-2007, 08:34 PM

You need to see FOUR instances of 32m Pi? :confused:

Just PRIME that OC! :p:

CraptacularOne

10-03-2007, 04:11 AM

You need to see FOUR instances of 32m Pi? :confused:

Yep I need at the very minimum four instances of P1 32m run simultaneously, or a screen shot of it priming at that speed @ 100% CPU load will be even better :) (multi threaded prime 95 25.5)

Viss

10-03-2007, 05:08 AM

Any news on L731Bxxx yet? Cannot find anything meself...

CraptacularOne

10-03-2007, 06:48 AM

Any news on L731Bxxx yet? Cannot find anything meself...

I haven't personally seen that stepping yet. So if you've got one crank it up and see what it will do :)

no_n|ck

10-04-2007, 03:02 AM

@CraptacularOne

Ic3man chip should be on top of the table, as it beats other 4ghz chips here --> 8h Prime95 stable, 501FSB:eek:, actual freq is 4009mhz ...

billdavis

10-04-2007, 03:55 AM

http://i107.photobucket.com/albums/m316/wcd26/Untitled5.jpg

Q6600 G0 - L723A795 - 4Ghz P stable - PC jinu117 - 1.485v - ASUS P5K Prem - by --------------billdavis

CraptacularOne

10-04-2007, 04:26 AM

Updated again :)

@ billdavis, thanks for making it easy, a simple copy and paste is always appreciated :up:

@ no_n|ck, I'm going by voltage needed. If you guys disagree, I'll move him up, but 4009Mhz is pretty much 4Ghz and he needed more voltage to get it stable than the others did ;)

no_n|ck

10-04-2007, 04:39 AM

@ no_n|ck, I'm going by voltage needed. If you guys disagree, I'll move him up, but 4009Mhz is pretty much 4Ghz and he needed more voltage to get it stable than the others did ;)

At least put his chip infront of turtletrax & tintin resualts, as 8h vs 30min of Prime95 :rolleyes: ... i bet his chip can do 30min of Prime95 @ 4ghz under 1.6v ...

ThePrutser

10-04-2007, 06:08 AM

At least put his chip infront of turtletrax & tintin resualts, as 8h vs 30min of Prime95 :rolleyes: ... i bet his chip can do 30min of Prime95 @ 4ghz under 1.6v ...

I thought this was an Q6600 OC database and not a ranking list :p:

CraptacularOne

10-04-2007, 06:39 AM

I thought this was an Q6600 OC database and not a ranking list :p:

It is and that is why his result is staying where it is ;) This is not a bragging rights thread just a data base of overclocks and voltages needed to get there his needed more voltage and thus is placed where it is at :)

no_n|ck

10-04-2007, 09:04 AM

I thought this was an Q6600 OC database and not a ranking list :p:

exactly, so thats why should the resualts be trasparent for someone whos looking for the right stepping ... i realy dont care as i have what i want, but from this point of view the turtletrax & tintin chips seams better on the table than are in reality :rolleyes: ... nevermind, at least we have something here