Corsair XMS2 CL4 > show 5-5-5-18 !!!!

[koc]

I bought match pair of Corsair XMS2 -6400 CL4

with 4-4-4-12 timing , however its show 5-5-5-18

http://www4.0zz0.com/2007/02/19/10/93555811.jpg

http://www4.0zz0.com/2007/02/19/10/33125105.jpg

the mobo P5N32-E SLI

and i set every thing ( auto ) in yhe bios

[JohnnyV]

I see it uses 1T command instead of 2T. 1T usually needs less agressive timings.
The memory is rated 4-4-4-12 with 2T command rate.
I guess you don't want to set everything to "auto".

[Kristoferr]

5-5-5-1T is little better than 4-4-4-2T So its ok.

[koc]

I guess you don't want to set everything to "auto".
so. what i need to change in the pios to correct the timing ?


5-5-5-1T is little better than 4-4-4-2T So its ok.
what i know that smaller no. better in timing !

[JohnnyV]

Just look at the timing table from your first screenshot of CPU-Z. and write down these values. Then enter your BIOS and go to your RAM settings. Insert values as mentioned in the table et voila!

1T is somewhat faster than 2T and it's said that latency timings for intel procs are not so important so perhaps the second setting is faster. Perhaps you can run some tests (Super Pi) to check which setting gets you to the end of the test sooner.

[mach82]

enable SLI Memory support in your BIOS. This will force your mobo to read memory timings from EPP instead of SPD.

[Bootup05]

Where is this setting BTW?

My ram seems to also be doing this in a P5B Deluxe

Stock speeds are 5-5-5-12-1T but cpu-z shows 5-6-6-18-2T

[koc]

Just look at the timing table from your first screenshot of CPU-Z. and write down these values. Then enter your BIOS and go to your RAM settings. Insert values as mentioned in the table et voila!

I try to do this . but the bios defferent from cpu-z , and i dont want write wrong values in bios .:( :(


enable SLI Memory support in your BIOS. This will force your mobo to read memory timings from EPP instead of SPD

http://www4.0zz0.com/2007/02/19/15/92923886.jpg

which no. should i select :confused: :confused: :confused:

[Gebba]

set the timings manually in bios =)

the motherboard automaticly sets bad timings just for bigger chans of booting upp whit many different memories.

[JohnnyV]

You really want to look for manual overclocking instead of automatic which is shown on your picture. And I think CPUOC means CPU OverClock :) so look for RAM settings instead

[koc]

set the timings manually in bios =)

the motherboard automaticly sets bad timings just for bigger chans of booting upp whit many different memories.


You really want to look for manual overclocking instead of automatic which is shown on your picture. And I think CPUOC means CPU OverClock so look for RAM settings instead

thank you all guys . i set the timing manualy in the bios and every thing OK

http://www3.0zz0.com/2007/02/20/14/37064046.jpg

:banana: :banana: :banana:

[mach82]

You would achieve better results after setting CPU OC 0%. Why better? Because the mobo would set better subtimings.

[koc]

You would achieve better results after setting CPU OC 0%. Why better? Because the mobo would set better subtimings

thanks man , i will try that :)