awhir
01-19-2007, 07:23 PM
ok followed the 3200cfx guide by tony and also used the g.skill hz sheet on dfi-street for ddr.
i have my settings posted below.
i was try to get my max cpu clock so i had the ram down to 100 but still had the ram a little bit tight.
but i cant put my ram any looser or make it 200 as it will not boot and i have to pull the battery.
any ideas on whats wrong with my settings i got as far as 2600 stable yet but i wana keep going but get this fixed first :(.
specs are
AMD Athlon 64 X2 3800 cooled by Tuniq Tower, DFI LanParty UT CFX3200-DR, ATI Radeon X1900 XTX , G.Skill 2GB DDR HZ PC4000 ,enermax noisetaker 600W, Seagaate Barracude 300GB,Seagate Barracude 320GB ,WD raptor 36GB , Akasa Mirage 62
Genie BIOS Settings:
FSB Bus Frequency............................. - 200
LDT/FSB Frequency Ratio....................... - 3
CPU/FSB Frequency Ratio....................... - 10
PCI eXpress Frequency......................... - 100Mhz
CPU VID StartUp Value......................... - StartUp
CPU VID Control............................... - 1.4
CPU VID Special Control....................... - auto
LDT Voltage Control........................... - 1.20v
Chip Set Voltage Control...................... - 1.34
DRAM Voltage Control.......................... - 2.75
DRAM Configuration Settings:
DRAM Frequency Set............................ - 100
Command Per Clock (CPC)....................... - 1t
CAS Latency Control (Tcl)..................... - 3
RAS# to CAS# delay (Trcd)..................... - 4
Min RAS# active time (Tras)................... - 8
Row precharge time (Trp)...................... - 4
Row Cycle time (Trc).......................... - 07 Bus Clocks
Row refresh cyc time (Trfc)................... - 14
Row to Row delay (Trrd)....................... - 02 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3684 Cycles
Write CAS Latency (Twcl)...................... -
DRAM Bank Interleave.......................... -
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
DRAM Drive Strength........................... - level 3
DRAM Data Drive Strength...................... - Auto
Max Async Latency............................. - 10.0ns
DRAM Response Time............................ -
Read Preamble Time............................ -
IdleCycle Limit............................... - 256 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 04 x
32 Byte Granularity........................... -
Bust lenght................................... - 8 *EXTRA*
http://i25.photobucket.com/albums/c88/awhir/untitled-1.jpg
http://i25.photobucket.com/albums/c88/awhir/untitled1-1.jpg
i have my settings posted below.
i was try to get my max cpu clock so i had the ram down to 100 but still had the ram a little bit tight.
but i cant put my ram any looser or make it 200 as it will not boot and i have to pull the battery.
any ideas on whats wrong with my settings i got as far as 2600 stable yet but i wana keep going but get this fixed first :(.
specs are
AMD Athlon 64 X2 3800 cooled by Tuniq Tower, DFI LanParty UT CFX3200-DR, ATI Radeon X1900 XTX , G.Skill 2GB DDR HZ PC4000 ,enermax noisetaker 600W, Seagaate Barracude 300GB,Seagate Barracude 320GB ,WD raptor 36GB , Akasa Mirage 62
Genie BIOS Settings:
FSB Bus Frequency............................. - 200
LDT/FSB Frequency Ratio....................... - 3
CPU/FSB Frequency Ratio....................... - 10
PCI eXpress Frequency......................... - 100Mhz
CPU VID StartUp Value......................... - StartUp
CPU VID Control............................... - 1.4
CPU VID Special Control....................... - auto
LDT Voltage Control........................... - 1.20v
Chip Set Voltage Control...................... - 1.34
DRAM Voltage Control.......................... - 2.75
DRAM Configuration Settings:
DRAM Frequency Set............................ - 100
Command Per Clock (CPC)....................... - 1t
CAS Latency Control (Tcl)..................... - 3
RAS# to CAS# delay (Trcd)..................... - 4
Min RAS# active time (Tras)................... - 8
Row precharge time (Trp)...................... - 4
Row Cycle time (Trc).......................... - 07 Bus Clocks
Row refresh cyc time (Trfc)................... - 14
Row to Row delay (Trrd)....................... - 02 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3684 Cycles
Write CAS Latency (Twcl)...................... -
DRAM Bank Interleave.......................... -
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
DRAM Drive Strength........................... - level 3
DRAM Data Drive Strength...................... - Auto
Max Async Latency............................. - 10.0ns
DRAM Response Time............................ -
Read Preamble Time............................ -
IdleCycle Limit............................... - 256 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 04 x
32 Byte Granularity........................... -
Bust lenght................................... - 8 *EXTRA*
http://i25.photobucket.com/albums/c88/awhir/untitled-1.jpg
http://i25.photobucket.com/albums/c88/awhir/untitled1-1.jpg