MAXLD
10-12-2006, 08:18 AM
Hi, first of all, my configuration:
AMD A64 3000+
Asus A8R32-MVP Deluxe (latest bios, 0602)
Enermax Liberty 500W
I have GSkill F1-4400DSU2-1GBFC (DDR550) memory modules but I can't put them working at 275Mhz, with my current motherboard. They supose to work properly at that speed...
In my old one (Asus A8N-SLi Premium) I was using them at 285MHz 1:1 (2.5-4-4-8, not sure about the exact values) @ 2.85V with no problem at all.
But with my current one (Asus A8R32-MVP Deluxe) I have SuperPi (2MB) errors with all the timing configurations I try.
The last ones I tried (3-6-6-11, indicated by SPD):
ADVANCED
_Jumper Free Configuration
_AI Overclocking__________________Manual
_CPU Frequency__________________275
_PCIE Frequency_________________100
_FID/VID Change__________________Manual
_Processor Frequency Multiple______X9
_Processor Voltage_______________1.45V
_DDR Voltage____________________2.85V
_VCORE Voltage__________________Disabled
_Northbridge Overvolt______________Enabled
___Core Voltage__________________1.3V
___HT Bus Voltage________________1.4V
___PCIE Voltage__________________1.2V
_PEG Link Mode___________________Auto
_PEG Buffer Length________________Auto
_AI Clock SkewA__________________Disable
_AI Clock SkewB__________________Auto
_CPU Configuration
_GART Error Reporting______________Disabled
_MTR Mapping____________________Continuous
_Cool N Quiet_____________________Disabled
_HT Link Speed___________________800MHz
_Memory Configuration
_Memory Timing Mode_____________Limit
___Memclock Value_______________200
_MCT Timing Mode________________Manual
___CAS (CL)_____________________3
___TRAS________________________11
___TRP_________________________6
___TRCD________________________6
___TRRD________________________4
___TRC_________________________15
___TRFC________________________19
___TRWT________________________4
_MCT Extra Timing Mode___________Manual
___TREF________________________7.8us
___DDR Input Strobe Skew_________Disabled
___Burst2Opt____________________Disabled
_User Configuration Mode__________Manual
___Read Preamble________________6.0ns
___Asyc Latency_________________9.0ns
___CMD-ADDR Timing_____________1T
_Bank Interleaving_________________Auto
_Burst Length____________________8 Beats
_Software Memory Hole____________Disabled
_ECC Configuration
___DRAM ECC Enable______________Disabled
___L2 Cache BG Scrub_____________Disabled
___Data Cache BG Scrub___________Disabled
_Hyper Transport Configuration
___HT Link Speed___800MHz
___CPU:RD580-NB HT Link Width____16bit
___RD580 HT Link Three State_______Disabled
___RD580 HT Drive Strenght_________Optimal
___HT Receiver Comp. Ctrl__________Optimal
___RD580 HT PLL Control___________High Speed
__________________________________________________ ____
With those settings I get 1 error after starting SuperPI 2MB... :(
I've tried 2T (CMD-ADDR Timing) also.... no improvements.
I've updated my mboard bios but no improvements also.
Could someone help me and tell me what could be the problem? :)
Thank you. :)
PS: I've tried to contact the european Gskill support (eurotech@gskill.com), asking if they could tell me the most reliable timing settings, but I have no reply yet...
AMD A64 3000+
Asus A8R32-MVP Deluxe (latest bios, 0602)
Enermax Liberty 500W
I have GSkill F1-4400DSU2-1GBFC (DDR550) memory modules but I can't put them working at 275Mhz, with my current motherboard. They supose to work properly at that speed...
In my old one (Asus A8N-SLi Premium) I was using them at 285MHz 1:1 (2.5-4-4-8, not sure about the exact values) @ 2.85V with no problem at all.
But with my current one (Asus A8R32-MVP Deluxe) I have SuperPi (2MB) errors with all the timing configurations I try.
The last ones I tried (3-6-6-11, indicated by SPD):
ADVANCED
_Jumper Free Configuration
_AI Overclocking__________________Manual
_CPU Frequency__________________275
_PCIE Frequency_________________100
_FID/VID Change__________________Manual
_Processor Frequency Multiple______X9
_Processor Voltage_______________1.45V
_DDR Voltage____________________2.85V
_VCORE Voltage__________________Disabled
_Northbridge Overvolt______________Enabled
___Core Voltage__________________1.3V
___HT Bus Voltage________________1.4V
___PCIE Voltage__________________1.2V
_PEG Link Mode___________________Auto
_PEG Buffer Length________________Auto
_AI Clock SkewA__________________Disable
_AI Clock SkewB__________________Auto
_CPU Configuration
_GART Error Reporting______________Disabled
_MTR Mapping____________________Continuous
_Cool N Quiet_____________________Disabled
_HT Link Speed___________________800MHz
_Memory Configuration
_Memory Timing Mode_____________Limit
___Memclock Value_______________200
_MCT Timing Mode________________Manual
___CAS (CL)_____________________3
___TRAS________________________11
___TRP_________________________6
___TRCD________________________6
___TRRD________________________4
___TRC_________________________15
___TRFC________________________19
___TRWT________________________4
_MCT Extra Timing Mode___________Manual
___TREF________________________7.8us
___DDR Input Strobe Skew_________Disabled
___Burst2Opt____________________Disabled
_User Configuration Mode__________Manual
___Read Preamble________________6.0ns
___Asyc Latency_________________9.0ns
___CMD-ADDR Timing_____________1T
_Bank Interleaving_________________Auto
_Burst Length____________________8 Beats
_Software Memory Hole____________Disabled
_ECC Configuration
___DRAM ECC Enable______________Disabled
___L2 Cache BG Scrub_____________Disabled
___Data Cache BG Scrub___________Disabled
_Hyper Transport Configuration
___HT Link Speed___800MHz
___CPU:RD580-NB HT Link Width____16bit
___RD580 HT Link Three State_______Disabled
___RD580 HT Drive Strenght_________Optimal
___HT Receiver Comp. Ctrl__________Optimal
___RD580 HT PLL Control___________High Speed
__________________________________________________ ____
With those settings I get 1 error after starting SuperPI 2MB... :(
I've tried 2T (CMD-ADDR Timing) also.... no improvements.
I've updated my mboard bios but no improvements also.
Could someone help me and tell me what could be the problem? :)
Thank you. :)
PS: I've tried to contact the european Gskill support (eurotech@gskill.com), asking if they could tell me the most reliable timing settings, but I have no reply yet...