Dfi Lanparty Sli-Dr Expert vs Gskill 600 FF

[cristyjocker]

I have this kit 2x512 gskill 600ff but there is no way to make them work with an dfi lanparty ut sli-dr expert.
somebody could make them worrk?



sorry for my bad english,i`m from spain.

[sanbe]

same bad things happen to me. I know the problem is with the Tccd samsung chips and Expert board. I know we should tune bios settings to make it works. But there is not any suggestion from G.skill support team to help us to find a stable config?

[GSKILL TECH]

try this

DDR600
2.6-2.8V; HTT=3; FSB=300
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2.5
Trcd: 4
Tras: 8
Trp: 4
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 1 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 8~9ns
Darm Response: Normal
Read Preamble Time: 5~6ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

[sanbe]

thanks mate, I will try theses settings.
Should I upgrade my expert with the latest bios?

[twisted5]

The expert and venus have always had a problem with TCCD memory. I have been tweaking for the last 2 days to see if I can get my FF to run at DDR600 1T and can't get it to work. I can go all the way up to 330 on my SLI-DR but nothing above 275 on the venus.

[sanbe]

I knew that 2 weeks later I bought (15 decembre 2005) my expert and gskill 4800FF. On the mb box DFI did not say: NO GOOD FOR TCCD RAM. I'm really disappointed.
Now I'm not sure if I should sell my mobo for no-expert version or my ram for 2gb UCCD.

[cristyjocker]

hy.
i have the same problem.....
I just dont know what to do.
Gskill tells that this memories functions correctly with dfi lanparty
Dfi lanparty tells that it works perfectly with Gskill 600 FF

what should I do now?

The correctly decision should be that gskill and dfi lanparty give me back the money and i give them his motherboard and ddr`s

[GSKILL TECH]

try DDS and DDDS at 1-1,2,3,4 or 3-1,2,3,4

expert really hard to work it on

at try tref to 133, 1.95us (3169 i think)

[sanbe]

But when you say "expert really hard to work it on", do you mean that we could find some settings to solve crash problems?
Because in my honest opinion, I think f1-ff doesn´t works with expert mobo at all.

[GSKILL TECH]

But when you say "expert really hard to work it on", do you mean that we could find some settings to solve crash problems?
Because in my honest opinion, I think f1-ff doesn´t works with expert mobo at all.
for me my FF is actually only up to DDR 604
i spend like 48 hrs to find out the best setting for it.
then i change FX60 to opty170.... not working again...

[sanbe]

do you think I will solve my problem if a change my mobo from expert to sli-dr? or may be will be better a nf4 ultra d?

[GSKILL TECH]

do you think I will solve my problem if a change my mobo from expert to sli-dr? or may be will be better a nf4 ultra d?
YES, i am 99% sure!
basically almost all DDR600 TCCD was using Ultra-D in XS