- help with making a phase change
- Stoopid Question
- Phase change
- Buy this defective Mach1?
- How to build a CPU DUMMY (200WATTS)?
- Phase change gurus...look what i found in the cellar...
- Advice on cap tube pinch'n
- Tell me if im right so far...
- To heat or not ?
- How many minutes does your evap needs?
- Baker blocks
- Where do I get a recovery tank?
- Copper gaskets?
- In need of block, cap tube, and suction hose, all completely assembled
- thinking of maybe trying to build a cooler (direct die)...go a few questions
- Move & Help
- How do you prevent condensation with your Mach I?
- Mach 1 ,,,Nventiv Questions
- Is the machI strong enough for dual evaps?
- what do i need to go get?
- Mach II and +24°C????
- Building my own phasechange setup
- Well my stuff came and I'm lost...
- Vapochill Tweakin'
- Using the Vapochill controller card
- Insulating system.
- Mach II GT compressor...
- Removal of refridgerant
- 3 new guides
- XS mentioned in computer mag.
- using straight propane
- change fans?
- R22 compressor for 507?
- Ideas on condenser for Danfoss SC12MLX?
- Little help for evaporator please...
- evaporator design
- condenser in chilled water?
- Wire this thing..
- Mach 1 has a leak
- I now own a Freezer
- Is this a decent compressor for my first direct die project?
- Thermal probes + Mach 2 controller board
- vac pumps on ebay australia
- Which would be more ideal?
- Can you identify this compressor?
- Aluminum evaporator
- 12V Adler/Barbour Cold Machine
- My Mach II on 404a & 60cm cap tube
- vapochill PE or mach (1)
- nVENTIV Mach 2 GTs have landed in the UK...pics
- 1/4 r22 or 1/5 r404?
- Attaching prommy to 9800xt
- Mach I
- Solenoid Valve
- How long till i power up the Mach 2 GT->which was left sitting on its side...
- a few queshions...
- Evap design...
- Vacuuming.
- vapo problem
- mach1 dual evap or 2nd cooler?
- New Mach1 User and build
- Captube length on Mach2 Modded
- alternatives to seperate PSU for Mach I startup
- Questions about the r404 mod on a Mach 1
- New CC Panel for Vapo LS
- compressor help
- Mach 2 contact troubles
- Auto-Cascade plan
- Finally did It......
- what evap?
- Adding compressor oil cooling
- My experience with Mach 1.
- Kit-Tronics is officially awesome.
- chongs phase change
- Kryotech SuperG2 Refrigerant?
- I have a serious problem...
- Vapo LS Probs / Bad Contact?
- a small question about copper tubing
- this moron needs some advice
- Need Help With Prommy Contact
- Mach II GT / Mach II Captube Length measurements
- Hows this vac pump?
- minifrostbyte
- a giant THANK YOU!
- Help me decide. Mach2 or Vapo LS
- Best gas for Mach II
- Is this komp. godd fore DIY?
- Building a phase change?
- Embraco Ffi 12hbk
- Where is the best deal to buy MachII in US?
- Question about compressor wiring
- Is this possible?
- Phase-change coming together.
- Thanx to: Chilly1,Tom Holck,Fugger,Gary,Marci.
- Gathering info and parts, gimme some help
- Will i have to regas my AC if i DD my proc?
- Parts Needed To Fill System
- How do they work?
- MACH 2 - Full Mod
- solenoid valve question
- System not working! Need advice!
- Need help with custom vapo!
- Comments/Ideas on First Phase Change Design
- I need something...help?
- Homevapo finished need help!
- re-wiring compressor
- Any probems covering the back socket are with seal string?
- Machii + Sk8v+ Fx-51!
- what to buy, mach 2, mach 2 st or mach 2 gt?
- Maybe useful bits?
- Cryogenic treatment
- Three Vapos in one case
- SK8V / MACH1 Question
- planning some stuff
- Need some advice - startup probs with GT & FX53
- Step by step inst/on of mach 2 cpu kit.Lets find why i get condensation
- Mach II GT arrived: Questions/Concerns I have about it
- Sealant Question
- Cascade - Planing
- Prommy + TEC?
- Cutting cap tube?
- Smallest cascade yet...
- Perfect controller
- How much would an ok vapor cooling cost?
- Question on VideoCards with Phase Change
- good temp range
- Questions Mach1 !
- This commpressor ?
- "Where to find...parts" questions
- What to do now?
- System assembly tech help. (baker block - baker help!)
- possible to change lcd panel on mach II?
- The Life Expectancy of a Mach 2 GT?
- Anyone got a clue what temp probes we can add in the Mach 2 control PCB?
- -200c in a single compact unit??
- Dielectric Grease.
- Running the Mach II without a Computer Attached?
- need help with future setup
- is this condensor ok
- how much money do u people spend
- temps on GPUs
- Vapochill on AMD = crushed core?
- Compressor Electrical
- Mach I gets to -10 then works real hard for 33
- Dual evap from one unit
- Copper or brass?
- strange noisese comming from Prometeia mach 1
- Removing a Compressor
- Epsilon : my new R404a direct on die system
- Who high did them 5800ultras on a phase change bench?
- New stuff
- TEC or Vapochill?
- The most simple Vapor cooling
- Will the Danfoss SC15CLX compressor do?
- 2 Evap Mach II?
- Having trouble
- Where to buy Insulation?
- Prometeia Mach1 front bracket
- non computer related airconditioner question!
- Cascade Drawings........
- question on argon
- Let the fun begin!!
- check out this water chiller
- Will a condensor in 2 parts ever work?
- Mach2 same performance as Mach1 ?
- I need some godly evaporator advice
- Have i missed bowmans mach 2 gt- vapo LS review?
- small direct die system
- Vasiline in CPU socket?
- W00T Got me a dealer account with danfoss
- Compressor gallery
- cap in baker block - scatch needed
- Tools and such
- how cool is your pc POLL
- Moving Gases around
- Are we there yet?
- 3/8 OD copper as a condensor
- about the lian li conversion kit
- My New VaporChill LS
- Quick questions on charging, recovery tanks, and liquid refrigerant.
- Tuning my DIY direct die unit
- Thoughts on ISCEON 89 (R13B1 replacement)
- Home made project - got a few question
- Prometeia1 vs 3400/64
- Charging and Recovery
- Thinking of getting an LS.
- what do you think bout this Evap design?
- oil seperator
- Which thermal compound to use ?
- can condensation burn board
- Dielectric grease - where to find?
- CPU overheating with Vapochill
- planning a phase change, help would be appreciated
- You ever broke your Mach 1 hose ?
- Change R134a to R404A.
- Wiring question again.
- Evap design basics...
- gas mod
- capilary tube
- guide on cap tube sizeing from supco
- Is there a great difference between MachII and MachII-GT ?
- ac fans connected to compressor dead?
- Obtaining a small condenser
- Capilary tube
- Shortening suction hose
- Case suggestions for custom prommie
- Givin R406A,R407C and R410A
- PSI vs PSG- WTF?
- Condensor Postion Limitation
- Anyone put an Vapochill LS on a VC yet?
- phase change literature in german
- Refrigerant question...
- How many 1PH Systems before...
- P/T Chart + More
- Enough Insulation?
- Flaring? Hows it work?
- Compressor as Vaccum Pump...
- How to get temps below -45.8 on r404?!
- Vapochill XE vs Prometeia Mach 2
- Anyone else using this Evap?
- Welding a acces port to a rotary compressor
- Hermetic,rotary,scroll?
- Americold compressor specs?
- Propane : dryer size and brasing the system
- Mach1 r404a Mod ! Please QUICK !
- Jumping in to deep? Help with NEW System
- Temp sensor on Mach2
- Condensor in chilled water?
- O/C temps ETC.
- My journey from liquid to vapour
- Lian Li modded for prommie
- ??? ls vs gt review???
- cpu condensation proofing
- Does any one make there own blocks??
- Can you run Phase 24/7 and 365??
- Wiring/Compressor Problems
- Evaporator mounting methods.
- Help Mach1 arrived !
- MAch I Vs Chaintech znf- 250 ???
- Anyone have...
- Can i braze with a pencil torch?
- homemade direct die
- REPLACE capilary machII
- Mach I and II kits are compatable
- The penguin got a GT, finally.
- Compressor's vibrating heavily
- Mach I regassing question
- Sweating Cooling Head - Mach I
- What Evap Temps you get ..
- R507