Johann's Flex suction lines

[johann]

Hi, I thought Id post some pics of the suction lines I make.

Stainless steel flex hose is 1/2" non braided and bends quite well.

Ends are that of choice but standard ends are 3/8"

Stainless to copper braze is 40% silver, copper to copper braze is 15% silver

http://emerald.srv2.com/~sokkiesc/Fotos/for_sale/suction1.jpg

http://emerald.srv2.com/~sokkiesc/Fotos/for_sale/suction2.jpg

[runmc]

Very nice work. Are your ends 3/8??:)

[johann]

Thanks runmc :D Yes the ends are 3/8" it looks smaller but thats because the stainless is a bigger bore 1/2"

[yngndrw]

Wow that brazing is so neat ! Looks awesome mate, good job. :)

[Gray Mole]

Well your brazing sure looks pretty :D

Nice, and it's very nice that you're in the UK as well, makes geting ahold of these things a lot easier.

Nice work, mate :clap:

Gray

[johann]

Thanks for the comments everyone!

[kayl]

johann glade you found a supplier.
thats the exact same stuff i use, i know what ya mean about the id of stainless steel. have you tried to braze them together yet??
its alot of fun.

[johann]

Kayl, that one is brazed :D

At first I couldnt get the filler metal to take on the stainless steel but that was because I was using the wrong flux, now I fhave found the right flux and rods and I quite enjoy brazing the stainless steel.

How does the 1/2" stainless steel work for you? Do you use it in your cascades?

I assume it works well as you have produced some of the coldest units here

[ayrtonsenna]

johann, just ordered one of your suction lines on ebay.notice you do condensors too. how long will you have them in stock??, looking to get one in a weeks time.
nice work by the way.

[quintus]

any site where i can buy 1???
thx

eastern europe

[johann]

quintus I sent you a PM

[LittleDevil]

Here is mine brazed flex hose...

http://www2.shrani.si/pics/picture0qzk01.jpg

http://www2.shrani.si/pics/picture0btu02.jpg

tnx

[johann]

Looks great!

[Icy]

Johann's suction lines are great using them on my system and they are amazing! nice and bendy and once held for a little while they hold there position well. A++++ heh

[MaRtIe]

i noticed on your website johann.... very clean brazing. im sure those will sell well here in the uk.

[pocketbikeuk]

these suction lines are great got one myself quite flexible

[fatty]

Very nice mate are you going to do braided as well also pm me your website ;)

[boardy]

Fatty website is www.ukphasechange.co.uk i believe ;)

[Gray Mole]

Gotta say I've been using some of Johann's Flex-lines and they're very good.

Large bore, no restrictions, and they actually seem to hold tighter corners than a lot of the smaller ones I've used.

Nice lines, well worth using :toast:

Gray

[4everCS]

Where can I get one of these things??? What is it under on ebay??

[MaRtIe]

did you not read the thread? lol www.ukphasechange.co.uk or PM him

[4everCS]

yes I read the thread!! and that site wasn't working for me but now it seems ok. I also PM'd him a while ago.

[Marvin]

;) Great FH. How much pressure can it hold ?

[MaRtIe]

yes I read the thread!! and that site wasn't working for me but now it seems ok. I also PM'd him a while ago.

Its early in the morning over here in England.. so im sure hes asleep.

He will get back to you when he can im sure of it... hes cool.

[Skinny13]

LitleDevil u use 40% silver braze,too?


Nice work guys!

[LittleDevil]

And another pair of suction lines

http://phasechange.extremecooling.net/littledevil/flex-line/1.jpg

http://phasechange.extremecooling.net/littledevil/flex-line/2.jpg

tnx

[Xeon th MG Pony]

Very very nice brazing :)

[Bergo]

could someone give me the name of a good north american supplier (preferably with an outfit in Canada) that I could purchase stainless braided suction line from? I ended up getting a teflon stainless braided suction line form yellow jacket, but it was too expensive, for my next few i"d like to cut the cost down a bit. sorry for the OT comment johann.