P4GD1 and Dottie 2.0 Information/Help [Archive]

MrBean

08-20-2005, 04:36 PM

Hello Everyone, ok, I have read the 2 threads that deal with Dothan, and the convertors, and have a slight poblem, which have not been talked about to much:

I have a new P4GD1 mobo, with 2.0 760 Dothan chip, and 479 convertor. I have flashed to bios 1005, and latest beta 1006, with same result. System works great, currently running old pci card, but when using overclocking toolz in WinXP (SP2), eg Clockgen, or SetFSB, my PCI and PCI-express bus increase.

This is set to fixed in Bios.....

Another thing, I can set my multi to 10X, then I should be able to set fsb to 200, and pci should return to 33, pci-Ex to 100mHz...they don't.

I have read Kamerat's thread, no real help. I am an experienced overclocker, but fail to see how Kamerat can set his multi low in Windows, then up his FSB to way past 200 without having pci/pci-ex issues?

Any secrets you guys want to share wrt this board? Will be appreciated.

All my settings are set according to Kamerat's, at least the important ones.

Thanx guys, would luv to get this sorted so I can supercool this little bugger. Mem is good old Mushkin LevelII black BH5's ;)

Br,
MrBean.

Lithan

08-20-2005, 04:49 PM

As I understand it, locks dont work on that board. And he runs the high busses by increasing the northbridge voltage (I think).

MrBean

08-21-2005, 12:37 AM

Mmm...somehow it would be difficult to run any gfx at either pci-ex or pci bus so highly overclocked. Even at 200FB, PCI would run at 49mhz, and if PCI-Ex is preset to 90mHz in Bios, it would still run 135mHz, if left at 100, it would run 150mHz.

a Little more possible on the PCI-Express bus, but I really don't want to risk one of my 2 7800GTX cards.....

These mobo manufacturers makes me sad....1st the DFI-SLi debacle, now this from Asus....they clearly state these will work with the adapter, but it doesn't.

Short of sending the board back, I am wondering if we can play with Bus Select pins on the cpu to trick the Bios into thinking this is a 200FSB part, and not 133?

Any advice/feedback/suggestions will be appreciated.

@ Bigtoe: Maybe you can have a chat with your closefriend that has ties with Asus to ask them what is up with these Bioses? It would be a great help if they can notify us if this will work in upcoming releases, or not, then at least we can plan a little better...please?

I don't really want to go back to AGP, as I have 2 7800 cards for my FX55 setup, so I want to use one to see if I can at least chase the singlecard 3dM03/05/Aq3 scores a little....

Otherwise I will have to get a 850 again, annd a P4C800-Deluxe mobo :(

Ah well, life is good, mofo-manufacturers sucks sometimes.

Thanx Guys.

death metal

08-21-2005, 01:54 AM

Boot at 200FSB and your bootstrap will be triggered at that point i.e. PCIe is fixed, same with PCI. While Kamerat was able to OC high, I don't agree much on his PCIe computation and used my PCIe computation.

Just to experiement with PCI/PCIe on this mobo, I used my 2.4c which is able to hit 280FSB on Asus P4C800 and P4P800 before. With all the settings on Auto, I just change the FSB and hit about 255FSB rock stable before trying to fiddle around with PCI and PCIe values. And btw, I am using an Inno3D 6600 128Mb PCIe VC for that.

MrBean

08-21-2005, 02:13 AM

toledo

08-21-2005, 06:40 AM

Thanx Death_Metal, suspected as much ;)

I need to mount the Vapo to be able to boot the 760 at 200 (x15), but that is ok then. I just thought that setting FSB from within Windows will also set pci/pci-ex to defaults again....obviously not.

Things would be so easy if the Multi-select work from within the bios...I will look at getting cheapish 6600 PCI-Ex card like you to play with.Thanx for you reply though.

Anyway, below some info I gathered from Mobile datasheet over at Intel...might help a few guys playing with their own setups. Use it, don't use it, no problem. Just copied some important info and pasted to text file.
Courtesy Intel ;)

Yes , would be much easier . I`m surprised that we still don`t have a bios with multi enabled for this mobo . I just ordered a 7800 gtx to use with this mobo also ......from what i`ve heard it is pretty safe untill 240 fsb (there is a buch of guys running at 240 24/7 no dead VGAs so far :D ) . It is sad having to choose a 730/740 chip to be able to lock the PCI bus , i have 770 here :(

MrBean

08-21-2005, 07:46 AM

@ Toledo:
I managed once or twice to get this mobo to boot with my 7800GTX Gigabyte card, but only when hitting delete on boot.....

I have made a few setting changes now in the Bios, and will try the card again.

Any advice here?

Kamerat

08-21-2005, 07:53 AM

I'm not sure that ClockGen shows the right PCI-E and PCI frequencies, it's even a notice on the cpuid.org site for that version of ClockGen: (http://www.cpuid.org/clockgen.php)
P5GD1
P5GD2 (*)
P5GDC (*)

(* ClockGen may report wrong PCI Express / PCI frequencies on these boards, as they use a different model of clock generator).
The version of ClockGen we are using is for the ICS954119 clock generator, the P4GD1 uses ICS954123(BF). Maybe this is the issue? :)

MrBean

08-21-2005, 08:03 AM

Hi Kamerat,
Yeah, I saw that, and I downloaded a beta version of SetFSB, but still, when upping my FSB, my pc would crash at around 39-41mHz on the PCI bus...I am using old PCI card.

Which Bios do you recommend, I have tried both on Asus's website, 1005 and 1006 beta.

Do you know anything about a 1.07 Beta2 bios for this board?

Secondly, did you also experience bad issues trying to get pci-ex gfx to boot?
Thanx for your replies, it is appreciated :)

toledo

08-21-2005, 08:43 AM

Hi Kamerat,
Yeah, I saw that, and I downloaded a beta version of SetFSB, but still, when upping my FSB, my pc would crash at around 39-41mHz on the PCI bus...I am using old PCI card.

What is the maximum fsb are you getting in windows without crash ?

MrBean

08-21-2005, 11:18 AM

toledo

08-21-2005, 11:45 AM

@MrBean

Don`t you have a PM730 ? You can try boot at 200+ and see what happens .

MrBean

08-21-2005, 12:02 PM

Only the 760. I believe the 200fsb will be fine, once you boot of it and it initializes proper speeds from Bios. But, still the busses will be all over the place once you start to use SetFSB or Clockgen.

I should be able to but at 15x200 later in the week, when I sort my cooling setup out. Phase should take me there.

Sume4

08-22-2005, 03:53 AM

@ Toledo: I can do around 2200mhz at default vcore, fsb then around 143mHz.....can do SuperPI without issues, but even increase in vcore doesn't help.

I 100% believe it is my PCI speeds giving me nonsense. Asus better get this board sorted, they really sell bad products lately. I forever had issues with their Mobo's, really bad Bioses, which is what kills them. So sad, because it has so much potential.

2 things on this board are bad: non-working locks, and iffy PCI-Ex support.

Exactly the same issues here with my P4GD1 + 760.. though i can run unbelievable 150fsb :p: I can run my system with radeon x850xt pci-e.

I´ve ordered P4C800-E Deluxe and x800xt pe with voltmodds already in place, maybe the 760 will run on that board because i can set the multi lower straight from the bios.

toledo

08-22-2005, 05:56 AM

Exactly the same issues here with my P4GD1 + 760.. though i can run unbelievable 150fsb :p: I can run my system with radeon x850xt pci-e.

I´ve ordered P4C800-E Deluxe and x800xt pe with voltmodds already in place, maybe the 760 will run on that board because i can set the multi lower straight from the bios.

Yes, I remember you complaining about the same problem . It is weird Dothans struggling to do hit 2200 . I hope you have better luck with your P4C

MrBean

08-22-2005, 12:38 PM

Terve Sume4,
Quick question: I am really struggling to get this board to POST with any 1 of either my BFG 7800GTX, or my Gigabyte 7800GTX. Normal old PCI-GFX card works fine though.

I must hit the reset button about 10-15 times, every time the system fans will start, then GFX fan will start, speed down, and after a couple of times, it will beep and POST.

This is with both 2.4B Northwood, Bios 1002, 1003, 1005, 1006beta, and on the Dottie with Bios 1005, 1006beta.

I am on the verge of sending this board back to my supplier, which will be a few days round trip, for another P4GD1....but, if this problems is in all P4GD1's, it is really pointless to get another 1. Instead then I should get a P4C800, and make a plan for a X850XT or similar :(

So, can I have input please, from any one using this board, if you are experiencing PCI-Express GFX card boot issues? If not, what GFX are you using?

Your help will be highly appreciated, Guys.

Thanx!

mrlobber

08-22-2005, 01:34 PM

I'd suggest testing another cpu first... Preferably one with a lower multiplier to see whether the cpu has not it's impact there as well. To find a C1 Dothan which acts just like a B1 one (no high fsb), and cannot run over 2200 mhz, it must be something special there and the motherboard might not be the only one at fault.

As for the PCI/PCI-E cards, I'm using a PCI one until a serious PCI-E beast arrives, had one cold boot (board didn't initialize video) at the very beginning, but Reset button fixed it and it has not came back since.

MrBean

08-22-2005, 02:24 PM

@ mrlobber: Thanx for the reply. The other cpu I have tried with exactly same results wrt PCI-Ex video initialization, was in fact a P4B Northwood CPU, not a Dothan.

I have not tried to push the cpu at all, because even with my Northwood, the system locks up when pushed pass 143fsb...and that cpu can do 3.4gig on air. Both 7800GTX's are new, I have proven their 100% functionality in my FX55/DFi-SLi-DR, since I sold that, my FX55/Abit-AN8-Sli setups.

So, to recap:
Used Twinmos BH5, Mushkin BH5, OCZ Rev2 TCCD, and Mushkin TCC5
Used P4 Northwood (Bios 1002, 1003, 1005, 1006beta)
Used Dottie 760 9Bios 1005, 1006beta)
Used Gigabyte 7800GTX, BFG 7800GTX
Used Enermax 600W, Aopen 530W (Fortron) and Antec 550W PSU's

The only GFX that this board inits everytime, is the old SIS PCI card. So, only other variable not replaced is mobo. It might be this board have issues with 7800GTX cards, I am sending it off tomorrow to my supplier, very nice guy, I asked him to dump his X850 in, and fire the board up a few times.

If it fails to init PCI-Ex properly, he will get a new board, and test it same way, before shipping it to me. If that fails, I will get P4C800-Deluxe, and focus on SuperPI. Was really hoping giving the Top10 a bit of a try again, managed it on several occassions before, but really hoped for a good bench session with single 7800.

CO2/LN2 tubes ready, VapoLS ready, so yeah.

Board ready = not. :(

Any inputs ideas?

toledo

08-22-2005, 02:37 PM

Any inputs ideas?

Kingpin does not seems to have problems running the 7800GTX and P4GD1 . I saw three guys running a 7800GTx on a P4GD1 , no problems so far . Probably is this board MrBean . I will run mine in a few days when i `m back to Brazil , hopefully i will not have issues .

MrBean

08-22-2005, 02:51 PM

Hi Toledo,
Soz man, didn't want to give you worries ;)

Thanx for the replies though, I will send it back to my supplier for a few tests. Probably the board, one thing I have noticed though, is when it fails to initialize several times, once it actually boots into windows, there will be small white single pixels all over the screen, like on normal pixel, one white pixel, horizontal, and vertical.

Then it will find new hardware, reload driver, and screen goes back to normal. Just wish I had a scope to measure bus frequency on the PCI-Ex bus when this happens.

But, I will have a new board hopefully by Saturday, and give some more feedback. Here's to hoping this is really the board, and that I can get a working specimen. Then forward to 200X15 :)

dfx

08-23-2005, 05:32 AM

Just got my setup up last night
All setting were configured in the Bios
Dothan 730 (Stock HSF) + P4GD1 + 2 x 512MB BH5 + 6800GT

BTW Mr Bean try configure those setting in the bios 1st
I tried Clockgen and EIST initially, it only make things worse
After getting the sweet, then this is what u will see in clockgen etc

Am i off topic?

http://i2.photobucket.com/albums/y14/5ubz3r0/Dothan2.jpg

MrBean

08-23-2005, 12:42 PM

Hi DFX,
Thanx for the tips. I will be getting my 2nd VapoLS quite soon, and I am expecting a new P4GD1 mobo by the weekend.

I send my one back, my supplier should give some feedback tomorrow evening, but I am pretty confident something seriously wrong with PCI-Ex bus signalling.

Once I have Vapo connected, I should be able to boot the 2gig cpu at 15x200, then I can give some more feedback.

Anyway, you're not off-topic, it is nice to see what other guys can do with similar setups. Anyway, you had some good, relevant input ;)

dfx

08-23-2005, 01:42 PM

I also had a Vapo LS might hook it up soon
But there's still some mods need to be done over the CT-479 and P4GD1
Signz..

MrBean

08-23-2005, 02:48 PM

Yip, I am also not looking forward to the head-mounting saga, but, a man's gotta do what a man's gotta do.....rofl....

The world of overclocking.....hehe

fumiya

08-23-2005, 04:36 PM

Hello,
I have a dothan 760 and a p4c800-e deluxe and I want to buy a p4gd1 for pcie.
If I can boot at 200*15 my pcie and pci would be locked fine ?
If I can't boot at 200 but lower (180) my pcie can't lock fine ?
thanks

MrBean

08-24-2005, 06:20 AM

@ Fumiya:

Yes, that is correct. Your PCI/PCI-Ex busspeeds should track correct at 100, 133, and 200fsb. At least this is the "Official" speeds these boards support, but it might also be correct at 166mHz FSB.

Can someone with a good overcloking Dothan check it out for us, please?

Thanx guys.

PcCI2iminal

08-24-2005, 09:12 AM

http://img304.imageshack.us/img304/323/187pci8sc.jpg

booting with 195 x 14 .

PcCI2iminal

08-24-2005, 09:29 AM

PcCI2iminal,
Nice o/c u got..
Are u on P4GD1?
If so, u use EIST to lower the mutlipier or ?

yep, thats a P4GD1 and EIST in use and js some NB cooler mod and 3.3v 4 my bh5

MrBean

08-24-2005, 12:22 PM

What's your SuperPI like? And what GFX you running at these speeds? Surely those speeds indicators for PCI/PCI-Ex are wrong?

hehe...imagine PCI-Ex GFX running at 180+ mHz....ouch....

edit: Well, new P4GD1 on it's way....supplier tested my old mobo, and verified it was buggered. PCI-Ex did not initialize for them either, they tried a few ATI and nVidias....

So, I should have it by Friday eve, and be able to post at least some prelim test results again, and test the board thoroughly.

Will keep you posted.

Br,
MrBean.

mrlobber

08-24-2005, 02:03 PM

Hey MrBean, nice to hear that it was just a single buggy board for you, I hope you'll enjoy the Dothan power soon with a new one :D

toledo

08-24-2005, 02:10 PM

Hey MrBean, nice to hear that it was just a single buggy board for you, I hope you'll enjoy the Dothan power soon with a new one :D

Yes . If i unrdestood MrBeam has some decent cooling for Dotahn . We will see some good benchs soon . Keep postin MrBean .

MrBean

08-25-2005, 12:34 PM

Hi mrlobber and Toledo,
Yes, I should have my new board tomorrow, my supplier has send it today, and verified it working ok! I am quite glad, the puzzle is coming together nicely.

Also ordered a new PC65 silver Lian-Li box, will arrive same time. Will take 2 hours or so to fit it to 2nd edition VapoLS, would look quite nice. My previous LS was fitted with black original Prommie/Lian-Li box, looked very nice indeed.

This time opted for silver, just to be different.

Just now to figure out a failsafe/good way to mount Evap on the Dothan. I already scavenged a decent heatspreader from an old (working) 2.4B, will get some RTV silicon tomorrow, lap the heatspreader, and do a testrun on air.

After that, and board verified ok, will I use liberal amounts of di-electric grease to protect board/socket/cpu against condensation. Never had any issues, even in the very humid coastal town where I live, Durban. Been using Vapos for the last 3 years, so quite skilled with them by now.

But, yes, hold thumbs, I will report back, hopefully we can hit 15x200 minimum. That would be a good starting point.

Any ideas and input from you guys would be appreciated ;)

PcCI2iminal

08-25-2005, 04:07 PM

Pi
25-26

I'm not sure about PCI speeds but soundz unreal 4 me.

And what GFX you running at these speeds?

7800GTX
http://img236.imageshack.us/img236/3527/207023d03dothan1gm.th.jpg (http://img236.imageshack.us/my.php?image=207023d03dothan1gm.jpg)

6800GT @ Ultra
http://img236.imageshack.us/img236/8017/15438dothan68009dv.th.jpg (http://img236.imageshack.us/my.php?image=15438dothan68009dv.jpg)

urbanfox

08-25-2005, 04:14 PM

What was that GTX spec'd at?

PcCI2iminal

08-26-2005, 03:56 AM

http://img385.imageshack.us/img385/4431/7800gtxalbatrongigabyte6rf.th.jpg (http://img385.imageshack.us/my.php?image=7800gtxalbatrongigabyte6rf.jpg)

Albatron or Gigabyte are the same(520/1420 @ stock air) and runnin SLI with both

MrBean

08-27-2005, 12:04 PM

Hello Guys,
Ok, posted this in mrlobber's thread as well.....but, here goes:

Received my new P4GD1 board, and Li-Li PC65 case to go with my VapoLS...

Typing this on the new board, with 7800GTX up and running, board came with Bios1002, had to flash to 1005 using Afudos and old P4 2.4B cpu.

Used PCI card to test at first, did a complete Bios reset after the flash, eg. removing power cord, changing jumper to pins 2-3 and removing battery.

After the procedure, mounted new 7800GTX, and P-M 760, and yeay....she boots :)

Did about 10 resets, from POST, from within Windows, not one problem to initialize 7800. I am quite happy, and will keep the system on air for the next few days, while I mount the Lian-Li PC65 case to the VapoLS, and sort out the mounting mechanism for the Vapo Evap.

Going to be fun, but I cannot wait to see what this cpu can do at 3000mHz. hehe.....

toledo

08-27-2005, 02:26 PM

Nice MrBean . I`m glad to hear it is working now . Have you got some results on air ? :)

jrw

09-02-2005, 03:22 PM

Got my setup working as well. Bought a real cheap 6600GT from Galaxy which is fine for my needs (Quake3).

Now I need to figure out this PCI-E freq thing. So far I use 115MHz @ 1.6 chipset voltage which allows me to run 220x12.

Weird thing is I got all the vcore I want. The board seems to overvolt by 0.1 or so :shrug:

Currently I run it set to 1.50 in bios and get 1.61 in CPU-Z and 1.60 i bios...

FunkyRider

01-07-2006, 07:39 AM

Feels bad after reading this post, I like to OC without volt raise but - my 740 cannot boot into windows @ 200x13 if not raise the voltage
This gives me no choice but to OC it hard cuz P4GD1 can't change multi in BIOS, what a crap

I think we should write complain mails to ASUS to force them come up with a BIOS supports at least multi change :slapass: