View Full Version : 3000+ Venice: 3194MHz Pifast || Budget ocing!
Epsilon
05-23-2005, 06:28 AM
Done on custom phase-change :)
http://valid.x86-secret.com/show_oc?id=19647
http://members.home.nl/epsilon/19647.png
http://members.home.nl/epsilon/temp/3000venice_9x355_266_3194_3836s.JPG
On this single stage home made phase change :)
http://members.home.nl/epsilon/phasechange_2/benchmarking03.jpg
Score on boxed air:
http://members.home.nl/epsilon/temp/3000venice_8x355_258_2845_4239s.JPG
max screenshot : around 3300mhz, will post tomorrow.
Need a new install, the NF4 drivers arent installed yet, only NF3 drivers. Will gain another 0.4sec or something :)
Other specs:
- DFI NF4 Ultra-D
- 2x256MB Mushkin old bh-5 (level2)
- PCP&C 510w sli psu
- 120GB WD 7200RPM (like it matters)
- FX5200 PCI
Micutzu
05-23-2005, 06:49 AM
Very nice! What was the evap temp at CPU idle ?
Mahoney
05-23-2005, 06:53 AM
Nice oc epsilon.! :toast:
What about the week and stepp??
Awesome result :toast:
And yeah, we want to know step and week :D
Epsilon
05-23-2005, 02:09 PM
Very nice! What was the evap temp at CPU idle ?
The evap temp (on the block) varied from -48c to -38 (depending on speed and voltage) :D.
That's in the very bottom of the block, so infact the CPU temp. -22c in bios btw ;).
Stepping:
CBBLE 0512 DPBW
xxxx0217
:)
Keelz
05-23-2005, 02:14 PM
awesome result :D
budgetoverclocking is cool :banana:
is just like the winnie's but these are even better :woot:
nice, what are your temps
Epsilon
05-23-2005, 11:21 PM
Maybe I will suicide shot today :)
Temps in the bottom of the evap vary from -48c idle @ 2800mhz 1.4v to -38c idle @ 3194 1.7v. Loaded the temps rise to -30c in the bottom of the evap block.
The sensor is here:
http://members.home.nl/epsilon/phasechange_2/evap09.jpg
And not on the suction as the Mach2 GT etc. The loaded temps at 3194/1.7v are -42c on the suction line :)
Epsilon
05-25-2005, 10:07 AM
And a suicide screenshot @ 3419mhz
http://valid.x86-secret.com/show_oc?id=19647
http://members.home.nl/epsilon/19647.png
don_vercetti
05-25-2005, 11:04 AM
quality graphics card! That is PCI i take it? What is it?
Very good speeds btw, maybe a bit of burn in will help it go even higher? How long have you had it for?
Epsilon
05-25-2005, 12:23 PM
It is brand new, this is after just 5hours of running both air and phase-change :)
It is FX5200 128MB PCI videocard
I use it for CPU benches because it practically doesn't take power so CPU has all :)
don_vercetti
05-25-2005, 12:33 PM
well a bit or burn in probably won't hurt then, i know it's physically incorrect at all, but it does seem to work, loads of people have noticed it.
Epsilon
05-26-2005, 10:26 AM
just wait and the CPU will go faster probably :D
Epsilon
05-29-2005, 11:48 PM
CPU will be sold
THis is the final result:
http://members.home.nl/epsilon/temp/3000venice_9x355_266_3194_3750s.jpg :)
piotres
06-05-2005, 01:49 PM
Wow ! Nice score Epsilon :toast: ...
Please write more informations about Phase-change- what compressor, what gas :rolleyes: ???
peter
NiCKE^
06-05-2005, 02:05 PM
Isnt that a WR? If it's post it in the WR thread.
V4n{}u|sH
06-05-2005, 02:11 PM
Great job and great CPU :toast:
cpulloverclock
06-05-2005, 02:20 PM
nice
which step?
I receive my 0517 DPMW wednesday :)
coolaler can bench at 3.41G with his 3000+
Shadowmage
06-05-2005, 06:42 PM
lol, phase change isn't budget OCing :(
GJ tho :)
HiJon89
06-05-2005, 06:45 PM
lol, phase change isn't budget OCing :(
GJ tho :)
Its "custom phase-change" which means the whole thing probably didn't cost more than $500, not exactly budget, but not exactly the high price you think of for phase change cooling
[XC] moddolicous
06-05-2005, 07:23 PM
Nice scores. I think with some tweaking and a little higher OC, 36sec in PIfast would have been possible.
Epsilon
06-06-2005, 06:50 AM
maybe it was possible, but I have to lap my evap first, contact wasn't 100%.
The thread of my cooling systems is over @ teampuss
Here is the thread:
http://www.teampuss.com/forums/viewtopic.php?t=605
But, because you have to register to view, I will post some specs here :)
It's a 14cc 1/2hp R404a compressor
runs with 3meter 0.031" captube
Propane as refridgerant
and chilly1 evap :)
idle @ -57c
Loaded with 180w @ -42c on the suction line (were prommy's are meassured)
-30c in the very bottom of the block @ load.
404Power
06-06-2005, 07:05 AM
HOLY SH*T! :slobber: :banana:
I don't know what to say.....
AWESOME RESULTS Epsilon! :D :D
Zyklon5
06-07-2005, 09:04 AM
Nice setup you got there ! congrats ! How did your Venice do on air maybe with a better week you could go higher.
Codeine
06-09-2005, 06:07 PM
Very impressive, you had some damn nice timings too. Selling that just after a hand full of hours, damn. I'd like to see what you can pull off on SLI with your coolng system.