View Full Version : vapochill xe
pancake
05-16-2005, 12:50 PM
got myself a vapo xe on the way after deciding i couldnt be arsed with the hassle of building my own. what kind of refrigerant can theese be re gassed with for better temps has 404a in at the moment
cheers
ZENNZZO
05-16-2005, 01:07 PM
got myself a vapo xe on the way after deciding i couldnt be arsed with the hassle of building my own. what kind of refrigerant can theese be re gassed with for better temps has 404a in at the moment
cheers
From what I understand, it would take modification akin to building your own to improve on the temp that it is already capable of...good luck with the new rig...
eshbach
05-16-2005, 02:01 PM
the 404a it has in it probably isn't worth changing. you could put 507 in it but it wouldnt' be that much colder than the 404 and it would cost you money. if you really feel the need to tweak it the best thing to do would probably be to tune the 404 charge to load for your system.
pancake
05-16-2005, 11:52 PM
ok thanks. what kind of power wattage does a 3200 winnie put out? currently got it at 2700 chip in sig with 1.56 ish vcore. whats safe to go upto on vcore on a vapo? can someone look on here (http://www.chillblast.co.uk/) in the vapochill section and tell me what i need to fit it to a skt 939 i think i need the complete socket kit for about £65 as its a vapo for socket a at the moment just want to clarify it before i buy it
cheers
pancake
Trixxy
05-17-2005, 12:18 AM
It's this one you need:
Vapochill Socket 754/939/940 & P4 478 Kit for XE/SE/PE
assuming the XE you're receiving only has a socket A head.
pancake
05-17-2005, 01:01 AM
yea it does .. cheers
Sume4
05-18-2005, 11:47 AM
Sorry i post to this topic but does anyone know if i could make s939 fittings for vapo SE s478.
Like bolts with nuts through the mobo and a piece of wood with paddings to the back.
Ofcourse i would buy the "upgrade kit" which contains new insulation and stuff.
And how about changing the gass to r404. Isn´t XE the same but with r404?
Sorry i post to this topic but does anyone know if i could make s939 fittings for vapo SE s478.
Like bolts with nuts through the mobo and a piece of wood with paddings to the back.
Ofcourse i would buy the "upgrade kit" which contains new insulation and stuff.
And how about changing the gass to r404. Isn´t XE the same but with r404?
ofcourse you can make your own holddown.
[Mounting hole Dimension Database] (http://www.vr-zone.com/?i=1356&s=1)
just make sure you insulate it well
Standard VapoXE has r404 in it.
pancake
05-21-2005, 09:44 AM
anyone got a recomendation for a case that will fit the vapochill compressor and bits and have room for watercooling pump and res... and of course all my pc components
pancake
05-21-2005, 10:47 PM
hmmm another slight problem. the power connector cable on the chill control is only 20 pin my tagan psu is 24pin and so is the dfi mobo. how can i get round that? is there a way to convert it to run off of plug socket instead of my psu
Sume4
05-21-2005, 11:59 PM
Yeong Yang, Server Cube YY-B0420 <-- this could do the trick for that case thingy.
pancake
05-22-2005, 12:30 AM
bit to much money.. at that price plus buying a new skt 939 kit i could of bought a brand new vapo xeII
Master_G
05-22-2005, 01:47 AM
PC75 is the one people usually use for putting 12V vapochills in, not sure how much room you would have for watercooling though if you have a dual rad or greater.
G
look here (http://www.xtremesystems.org/forums/showthread.php?p=844440#post844440), lots of space in a lian li pc70 :)
ofcourse you can make your own holddown.
[Mounting hole Dimension Database] (http://www.vr-zone.com/?i=1356&s=1)
just make sure you insulate it well
Standard VapoXE has r404 in it.
good link ;)