X850xt Damage

[K!D-a]

Hi guys From Germany :( plz can u messure those 3 resistors i marked on the pic , i wantet du screw my new coole but i cut off the resistors ....

damn i am unlucky plz help


btw: sorry for my english

[FUGGER]

Welcome to XS, if you had a pic linked I could have answered your question.

You can look in vmods section for another pic of a board like yours too.

[K!D-a]

thanks allot :) very fast i am working on it pic will follow :) thanks fugger


first are r159 and r158 its near the pci-e slot where i can screw up the cooler ..... and then r340

[K!D-a]

Fugger plz help :( anyone who can messure those resistors ? ( on the card not off mountet

[K!D-a]

No one that can messure these 3 resistor for me ?

Ps: same layout as the X850xt pe

[runmc]

I'm sorry, my X850XT is in rma at the moment. I am not able to check those values for you right now.

Ron

[K!D-a]

Fugger wanted to help me but hi , has no time or so .... :banana::banana::banana::banana:ing screws argh

Ps: card is working .... massive pixel errors but wenn i pencil the solder point where the resistor's where with a HB pencil errors are nearly Zero .... i need the values of those 3 resistors

R340 <--- Upper Right Corner from the chip (back of the card ) R159 and R158 Lower left Corner (back of the card )

[FUGGER]

I believe those resistor packs are 0k

I can confirm in a little bit. I dont have a x850 handy atm.

[K!D-a]

thanks i have made better pics now look up :) u meen i can draw ssl ? in german Silber-Leit-lack ?


Btw: you meen i can close these Contacts ? :confused:

[Holst]

I believe those resistor packs are 0k

I can confirm in a little bit. I dont have a x850 handy atm.

They look like shunts to me.

If they are you are lucky k!D A as you can just bridge them with a strand of wire.

To prevent this sort of damage in future use plastic washers on your cooler mountings.
You can also put electrical tape over the hole then poke the screws through it to protect the surrounding components.

Is your name from the radiohead album?
I prefer the classic Bends myself :D

[Holst]

A shunt is usually solid black and has no markings.

If you test the others that you did not damage (EG- R150) and they are closed circuit then you should be safe to short over the broken ones.

Good luck.

[K!D-a]

jeha first man in the world who checked this :) i love raidiohead ;) ok .... i will brigde them an come back then . wish me luck *thumbsup*

[K!D-a]

ok i have closed the "Pack" R340 but the 2 other are no shunts massive errors if they are closed (short pc on and see crappie screen :eek: .... hmm no one who can mess ? ;) i hope my hp pencil will do the rest then ...

[K!D-a]

R158 seems to be an shunt but i am not shure ... R159 ? :eek:


So Far R340 shunt ( "Brücke" in German ;) )
R159 :confused:
R158 :confused:


Btw: my english returns ;) :cool:

[Holst]

Better get soembody to measure them then..

Can somebody help out as I only have a mere 9800pro :(

[K!D-a]

i think fugger will do tomorrow ;) i go to bed now 01.10 o clock in germany ;)

[K!D-a]

Hi something changed ? Fugger ?

[K!D-a]

I believe R340 is arround 9K ? right Fugger ?
But the 2 other :\ i will be waiting :) i hope fugger will help me :)

[K!D-a]

Can no one messure these :banana::banana::banana::banana:ing Resisitors mountet on the card :stick: :(

[K!D-a]

No one help me :(

[craig588]

Try PMing him, maybe he forgot to look in this thread.

[K!D-a]

Thanks alot :)

[K!D-a]

no help at all

[W1zzard]

r158 40.2 ohm
r159 100 ohm
r340 10k ohm

[K!D-a]

danke wizz :) wenn ich mal zeit habe komm ich mal nach Stuttgart und dann gehen wir einen kippen ;) danke echt

[perkam]

danke wizz wenn ich mal zeit habe komm ich mal nach Stuttgart und dann gehen wir einen kippen danke echt

LOL Though Saaya wont like the fact that you wrote in a language other than English, he can read german I believe :p:

K!da, pls do report back with results of your repairs :up:

Perkam

[K!D-a]

i will do :) hehe i wrote thanks wizz ;) if i come to Stuttgart we drink some beer :p: :toast:

[K!D-a]

Card is back on working ;) 600/600 on air no artifacts or something :) thank u all
and remember

R158 40 ohm
R159 100 ohm
R340 10k ohm ;)

[roger_h99.nor]

Followed this thread with intrest, must say I never thought this card should come alive again.. Great work, congratulation Kid-a.

[K!D-a]

Thanks :)

[Dumo]

Card is back on working ;) 600/600 on air no artifacts or something :) thank u all
and remember

R158 40 ohm
R159 100 ohm
R340 10k ohm ;)What you did actually? B/way goog job :clap: :toast:

[K!D-a]

actually i solder on R158 1k poti 40 ohm (off mountet ) mountet 29 ohm
R159 1k poti 100ohm (also off) mountet 39ohm
R340 Nothing ..... allready 8.9k works ;)

[Mehmet_Ali]

K!D-a good job.Saved 500$