The Official Venice Overclocking Thread

[Perc]

dammit man thats not cool at all. that chip would need a good phase unit to stay under that voltage... this one i got aint to bad at all im at 3000mhz using 1.5v in the bios but windows it only reads 1.456v.

peace perc,

[Absolute_0]

Very nice chip perc. I know once you give it some real volts it will be way past 3 Ghz.

I always use CPUZ for the V readings so that looks like 3 Ghz with 1.45 volts.

[laydback]

Anyone had any experience with an E6 3500 Venice?

I want to know if there's something I'm overlooking on the configuration side or if some hardware component is holding me back. I'm pretty sure my ram is holding me back but I want to make sure before I make my next purchase.

So far I've reached the best stability and performace with my settings as follows:

HTT:240
Hammer Multi: 11x
Mhz: 2640ghz
HT=3x 16x16
Ram Timings=1:1 3-3-3-8 1t
Vcore: 1.65v
VDimm: 2.8v
Chipset: 1.6


A64 Venice 3500+ E6 LBBWE 0528APAW (Naked Core)
Zalman cnps7000-cb
BFG Nforce4 Ultra Mobo
Samsung TCCC 2x512 Dual-Channel Rated at 3-3-3-8 1t
Enermax 550w PSU 5v-36a 12v-36a
ATI Radeon x800xl PCI-E 256m cooled by a Zalman vf700-cu
SBLive 24bit PCI
WD 250gb SATA

[Perc]

Very nice chip perc. I know once you give it some real volts it will be way past 3 Ghz.

I always use CPUZ for the V readings so that looks like 3 Ghz with 1.45 volts.


why thank you :) heres a shot of 310htt 1:1 non suicide shot this is very benchable!!

peace perc,

[njkid32]

why thank you :) heres a shot of 310htt 1:1 non suicide shot this is very benchable!!

peace perc,

Hey perc nice oc and very nice chip! :woot: What temps are you getting? Are they much lower than the X2?

[Perc]

hey thx man i bought it off this kid who didnt know what he had :slap: ! hey this is my latest super pi 1m run. have a peek i think its decent. ive never realy had good super pi times before...

peace perc,

[funkflix]

New one.. 0520EPMW with IHS. It rocks! :toast:

http://img375.imageshack.us/img375/3179/2700mhz139vihs7cu.jpg
http://img218.imageshack.us/img218/5159/2800mhz139v2m3xs.jpg
http://img314.imageshack.us/img314/1607/2800mhz139vprime6mv.jpg
http://img139.imageshack.us/img139/3849/2910mhz15v2m7mv.jpg
http://img355.imageshack.us/img355/5222/2910mhz15vprimemitihs4nt.jpg
http://img26.imageshack.us/img26/6267/3000mhz2m155v4fj.jpg
http://img370.imageshack.us/img370/7240/2950mhz156vprime4ie.jpg

[Absolute_0]

Extremely nice CPU... now let's see 10 hours of SP2004. Looks like it will run 3 Ghz pretty easily with a little more volts. I am prime stable at 3 Ghz but it requires 1.73 volts, load temp @ 39-40C. With that many volts that CPU would probably be around 3050! :drool:

[funkflix]

Ur CPU is without IHS?

I've pluged in this CPU 2h ago, had no time to run longer Prime95, just testing what i can expect. :toast:

[Absolute_0]

Yep IHS removed

I forgot your IHS is still on - that is a very sweet CPU! Dont forget to do burn in.

[funkflix]

Yeah, maybe i should try an Burn-In, but my PC is 20" away from my bed, so i can't sleep.. we will see ;)

[Jupiler]

Grave :

you got yourself another one? What happened with the first one? Week 20, if I remember correctly.

[funkflix]

Yes, the other one is already by his new owner. ;)

Got this CPU today with mail from ebay.

[Jupiler]

Very nice results.
You're very lucky finding a good performing week 20. :toast:

[funkflix]

Thx, but the finder is a friend of me! ;)

Anyway, i have fun to test this great CPUs! :toast:

[Off-Topic]
Do u have permission to change titles? :)[/Off-Topic]

[ianocean]

3200+ Venice E6 LBBWE 0531 EPEW maxing at 2.5Ghz 1.6v :slobber: but first time i can bench SPi 32M stable my TCCD over 300mhz 2.5-3-3-7 1T -good IMC indeed
http://img50.imageshack.us/img50/51/306trcd35cy.th.jpg (http://img50.imageshack.us/my.php?image=306trcd35cy.jpg)

[Perc]

yeah im lovin my 3200 venice. these chips are deff nice im at 3100mhz now using 1.55v in the bios and cpu-z is showing 1.504v wich isnt bad. one thing im starting to notice is that anything over 1.6v the cpu will eror out in super pi where as with less volts it doesnt :shrug: im thinking that if you cant get your oc using less then 1.6v then your screwed! atleast with the cpu i have anyways....

peace perc,

[funkflix]

Final results, no time for longer testing. :

http://img297.imageshack.us/img297/2262/2950mhz156vprime95withihs4eq.jpg

[Hugo van Dijk]

Final results, no time for longer testing. :


:toast:

That,s a sweet CPU :slobber: :slobber:

:clap:

[Absolute_0]

Very nice, looks like my CPU but needs .1 volts less! That is sweet stuff

Here is my CPU on the DFI NF3, this is back when it still had the IHS
http://img.photobucket.com/albums/v729/absolute035/overclocking/2.jpg

[JfRsQ]

:slapass: yeah im lovin my 3200 venice. these chips are deff nice im at 3100mhz now using 1.55v in the bios and cpu-z is showing 1.504v wich isnt bad. one thing im starting to notice is that anything over 1.6v the cpu will eror out in super pi where as with less volts it doesnt :shrug: im thinking that if you cant get your oc using less then 1.6v then your screwed! atleast with the cpu i have anyways....

peace perc,

I'm getting similar results with my 3200+. 1.7V is instant freeze as soon as I'm clicking an icon on my desktop :slapass:

[Perc]

look at this cpu :drool: njkid is getting some damm sweat cpu's!

http://img182.imageshack.us/img182/5776/capture092420051259327ed.png

peace perc,.

[Absolute_0]

lol perc, he just showed me that pic, i was so amazed! Now he just needs to bump the voltage up...

its 0521DPMW 0098 btw.

[funkflix]

Cooling*? IHS? ;)

* Got it.. Mach 1

[njkid32]

Well I just picked this thing up and popped it in. I didnt even run it at stock. I just wish my ram would do 330. LOL to bad I prolly am going to sell it.

cpu-z verify----
http://valid.x86-secret.com/show_oc.php?id=39888

http://img264.imageshack.us/img264/9795/dscf08002iq.th.jpg (http://img264.imageshack.us/my.php?image=dscf08002iq.jpg)

[Perc]

your not selling that cpu and if you do its going to me :) no way am i letting that slip away to anyone else.... these 0521DPWM steppings i hardly see on these forums and the ones i do see are ocing like mad! shame you cant run that thing at 1:1 past 310htt i gues a divider doesnt hurt that much just a shame thats all. nice chip man make sure you let me know if you sell it...

peace perc,

[uOpt]

I don't have Windows running to get a CPUz shot, but this survived a full day of FreeBSD's `make world`, which is a very hard test (recompiling the whole system with itself, and any memory error leads to compilation failure).

My E6 3200+ does 2500 at 1.525 volts (ram under 200 MHz) with a Zalman CF-7700-CU at full RPMs.

2600 MHz did not run even at 1.50, so I'm testing 2550 now.

The DFI LP Nf4's temperature readings don't work in FreeBSD so I have no idea.

[CaliPo]

Hello!! What Can you tell me about this Stepping ? 3800+ Venice

ada3800aa4BP
lbble 0524 EPMW
z707522f50961

Thanks!!!

[b1tterman]

Venice 3000+
ADA3000DAA4BP
YBBLE 0523CPGW
Q337396F53002

8*337@1.65v
cpu-z ID 30607

All that runs on crap Gigabyte 100$> board K8NS-939 with nf3 ultra chipset
so i thinks its the boards limit

cooling= very custom home made gas cooling, temps about 5-10 degree Celsius
didnt manage to take any pics except of cpu-z verification because cooling began to leak, waiting dor dfi nf4 sli-d to arrive to maxx out and some gskill pc4400 is on the way too

[dnottis]

All on air, thermal take big Typhoon cooler..


http://www.3dxtreme.net/other/CPUS/3700%20CABGE%200515SPMW/IMG_1960.jpg

Low volts - prime, occt and super Pi stable.
http://www.3dxtreme.net/other/CPUS/3700%20CABGE%200515SPMW/110-3-2005-1.38.53%20PM.jpg


High volts - OCCT and Super PI32M stable, not prime stable though.
http://www.3dxtreme.net/other/CPUS/3700%20CABGE%200515SPMW/2915.jpg

[njkid32]

Well here is the newest chip I got today just a couple of hours ago. Its another 0521DPMW batch is 0070 nice and low just like I like it! But here is just my initial testing but there will be more to come.

http://img316.imageshack.us/img316/9251/capture100620050008578xr.th.png (http://img316.imageshack.us/my.php?image=capture100620050008578xr.png)
http://img99.imageshack.us/img99/5884/capture100520051657269mg.th.png (http://img99.imageshack.us/my.php?image=capture100520051657269mg.png)

And the highest so far at 1.5v
http://valid.x86-secret.com/show_oc.php?id=41864
http://valid.x86-secret.com/show_oc.php?id=41932

[Mehran]

WOW!
I don't believe these results
I now can hardly get my CPU stable at 2750.
Not sure what is causing my problem.

[funkflix]

Well here is the newest chip I got today just a couple of hours ago. Its another 0521DPWM batch is 0070 nice and low just like I like it! But here is just my initial testing but there will be more to come.

http://img316.imageshack.us/img316/9251/capture100620050008578xr.th.png (http://img316.imageshack.us/my.php?image=capture100620050008578xr.png)
http://img99.imageshack.us/img99/5884/capture100520051657269mg.th.png (http://img99.imageshack.us/my.php?image=capture100520051657269mg.png)

And the highest so far at 1.5v
http://valid.x86-secret.com/show_oc.php?id=41864
http://valid.x86-secret.com/show_oc.php?id=41932

Nice results! :toast:

Sure u doesn't mean DPMW instead of DPWM? :)

[njkid32]

Nice results! :toast:

Sure u doesn't mean DPMW instead of DPWM? :)

Oh yeah LOL your right typo!

[Burnt_Ram]

Oh yeah LOL your right typo!holly crap dude ! nice OC, congrates ;)

[funkflix]

Today i got an second 0520DPAW, dropped it in and first boot with this settings.. Prime runs fine! :D

Really great stepping it is! :toast:

http://img331.imageshack.us/img331/2954/30000kv.jpg

[funkflix]

Does exaktly the same as my first 0520DPAW. I think i can expect 3100MHz SuperPI 1M too. :toast:

http://img231.imageshack.us/img231/4786/2925prime95noihs157v1yb.jpg

[PC-ZONE]

What do you think of thes OC?
http://valid.x86-secret.com/cache/42470.png

Here the validation:
http://valid.x86-secret.com/show_oc?id=42470

[Mehran]

Very nice!
What cooling r u using? What Steeping is that?

[PC-ZONE]

http://valid.x86-secret.com/cache/42561.png

Validation: http://valid.x86-secret.com/show_oc?id=42561
I use the boxed cooler but have a nice ventilation in the cabinet ;) (35° full load)

[funkflix]

What's up with some SuperPi;Prime95 or other benches? SS are a bit boring.. and Vcore? :rolleyes: ;)

[njkid32]

Well here is another addition to my collection of chips. LOL (sorry not bragging!) This one is one of 2 0517BPDW's that I just picked up. I dont think they are as good as the 0521DPMW's that I have. This week 17 doesnt scale the same way. It needs alot more voltage to hit the same speeds as the week 21 chips. But this is still a pretty good clocker. Here are some tests right out of the box. Maybe the voltage will improve with some burnin or just day to day use.

http://img80.imageshack.us/img80/3831/32ghz13qp.th.jpg (http://img80.imageshack.us/my.php?image=32ghz13qp.jpg)
http://img80.imageshack.us/img80/8054/32ghz21pl.th.jpg (http://img80.imageshack.us/my.php?image=32ghz21pl.jpg)

[njkid32]

Ok I finally got around to testing the other 0521DPMW and it seems to be doing pretty well. Its the one on the left side of the pic.

http://img438.imageshack.us/img438/4337/newchips24in.th.jpg (http://img438.imageshack.us/my.php?image=newchips24in.jpg)
http://img294.imageshack.us/img294/9796/32ghz5cm.th.jpg (http://img294.imageshack.us/my.php?image=32ghz5cm.jpg)
http://img421.imageshack.us/img421/3849/cpuz336ne.th.jpg (http://img421.imageshack.us/my.php?image=cpuz336ne.jpg)
http://valid.x86-secret.com/show_oc?id=42902

Edit--just messing with this chip a little more and here is a cpu-z shot of 3.6ghz.
http://valid.x86-secret.com/show_oc?id=42910

[Warship]

dang, got an E6. Not cool... well, I won't be OC it, I'll see how much I can undervolt it at stock clock. (The CPU is for a CnQ-HTPC)

[Dave_Sz]

Jesus, you won't OC it cuz it's a E6? WTF? I have 2 E6 at 2.6ghz+ with 1.5v or so.

[Slipknot]

http://web-upload.com/uploads/ebay.jpg


Dont know if my power supply (350W, installed a 7800GTX) is too weak for more MHzs.
LBBLE 0521CPMW :-(

[dqniel]

Anybody know where I can buy a decent Venice anymore? I've been browsing for sale forums, etc...but it's nearly impossible to find a good week or a proven OC'er.

[PEARLboy]

I bought one venice 3000+ and his step is:
ADA3000DAA4BW
LBBWE 0521DPBW
Z510316F50831

I want to know as I can give with him. my mems is Patriot XBLK TCCD (which the best times for them?)

Sorry for my english...

thks :D:D

[Slipknot]

I bought one venice 3000+ and his step is:
ADA3000DAA4BW
LBBWE 0521DPBW
Z510316F50831

I want to know as I can give with him. my mems is Patriot XBLK TCCD (which the best times for them?)

Sorry for my english...

thks :D:D


Same week, so its possible that ya CPU will go like mine...

[njkid32]

I have a 0521DPMW 3200 that does really well. So it looks like the 0521's are the way to go now for the Venice.

[Xerxes]

Venice 3200 LBBLE 0525 CPMW using an XP-90 and a sanyo-denki.


http://img242.imageshack.us/img242/5867/venice27wbal9mc.th.jpg (http://img242.imageshack.us/my.php?image=venice27wbal9mc.jpg)

[x3ro]

I finally got my new mobo today and after some quick testing i got this at stock volts..

validation link (http://valid.x86-secret.com/show_oc.php?id=44372)

Regards

Btw the ram is just at 1xx mhz cuz its bh5 and i dont got the ddr booster or voltmod... and i cant find my beloved tccd's :mad:

[Fallengod]

Does anyone know. Is this good stepping for 3200 venice? Thinking of buying one from a guy for $115. Thanks.

LBBLE 0516EPGW

[goob982]

3200+ E6 Venice can anyone tell me anything about these. How high you have got them to overclock...

ABA3200DAA4BW
LBBWE 0529DPGW

I am right now at

2.4 @ 1.45vcore.

Asrock 939Dual-Sata 2 OCWB beta 2 bios

Havent done any vcore mods so 1.45 is the highest I can go. Thinking about going ahead and doing the mod.

Running danger den water cooling... current temp is 25C.

Thanks

[mbm]

Have been offered this stepping
Opteron 146 cabye 0536 gpmw.
Is this much better than my CABGE?

[Fallengod]

I think you got the wrong thread. This is venice thread. Theres an opteron thread you should ask.

But the answer to your question is yes. CABYE is good. CABGE = BAD

Have been offered this stepping
Opteron 146 cabye 0536 gpmw.
Is this much better than my CABGE?

[laydback]

I finally got my new mobo today and after some quick testing i got this at stock volts..

validation link (http://valid.x86-secret.com/show_oc.php?id=44372)

Regards

Btw the ram is just at 1xx mhz cuz its bh5 and i dont got the ddr booster or voltmod... and i cant find my beloved tccd's :mad:

Lets see a prime screenshot of 2.8ghz for 6 hours

[dimasdw]

I found E6 Venice 3200 with this stepping 0533 BPBW,are this good stepping ?

[[XC] 4X4N]

Lets see a prime screenshot of 2.8ghz for 6 hours

Here's 24+hours prime at 2.8 with venice in my sig. Might be selling it now that opty is looking to be a better chip.

[Fallengod]

If you are selling it, let me know.

[[XC] 4X4N]

Haven't decided yet, maybe in a couple of weeks.

[Quad Master]

Can someone give the best Venice weeks after 20th week.
As i cant find the beautiful 17th week here in India now.

Will be using it with a DFI Nf4 Ultra-D

Will be cooling it with a XP90 or a SI120.

Wanted a 3000+ Venice which will atleast OC till 2.9Ghz

Please Guys i am completly relying on you guys for this info.
Also if its posted in some thread please post the thread that would also be useful.

Earlier i had seen a Venice Core Database thread where many people with there
15,16,17,18th week venice had posted there max oc's on air , water & ln2.

[Fallengod]

Got a prime95 question for someone. Ocing my 3200+ venice on my Epox 9npa+ mobo.

Trying to OC at 2.5ghz right now. I am at 1.55 volts. It was the same error with 1.5 volts. I just did 10x multi with 250 frequency. Ive tried it with HTT at 5x, 4x, and 3x. All similar errors. Memory is relaxed right now at SPD settings. Which is 3-3-3-9 2t right now at 2.7volts(to rule out memory problems. My memory is Corsair XMS 4400C2PT which is TCCD. So its not the memory...

What does this prime95 error refer to? CPU related? Voltage? Memory?

Test 1, 400 Lucas-Lehmer iterations of M11922945 using 1024K FFT Length.
FATAL ERROR: Rounding was 0.4999991484, Expected less than 0.4
Hardware failure detected, consult stress.txt file

[Superb]

Hi, my clockgen for nf3 just stopped reading the correct cpu clock, it shows amzingly high clock speed :( What can the problem be? CPUz is working fine tho.

I will now reinstall my nf3 drivers. Still reporting wrong numbers.

[DudeMiester]

Here fooling aound on my dad's new computer. It's a A64 3200, ASUS A8N-E, 2x512MB OCZ Premier setup. Just doing some SuperPi 1M runs with 1.525v (BIOS), and this is my best so far. Also, I can't seem to get any better then around 2.65Ghz Prime95 stable even with extra volts (i.e. I get the same result with 1.475v), and I get the same error as "FallenGod". Then again, given my dad probably won't be using this for anything other then offic work, I think that's more then enough, lol.

Oh, I didn't get a chance to see the stepping before the CPU was installed :(, but afaik it's not that great. This is one of the AMD Tech Tour chips.

One other thing, this is on WinXP x64 Pro.

http://valid.x86-secret.com/show_oc?id=48403

[AP0ll0UK]

I've had my system for a few months now and everything seems fine except the odd problems from CSS / HL2 which I believe are related to their rubbish updates. Anyway, aside from that all is well.

Does anyone have any idea how far I would be able to push my system?

Everything is in my sig except this: - LBBLE 0516 DPMW

I played around with overclocking a few months ago but didn't have the time to do all the required testing so I left it for a while. Anyway, I have a bit more time that I can spend doing some benchmarks and tests and leaving it running Memtest and Prime so all I need now are a few pointers to some good primers relating to the Venice's.

If anyone has any experiance with a similar week Venice 3500 then your comments would be greatly appreciated.

Thanks

[hawkeyefan]

Can someone give the best Venice weeks after 20th week.
As i cant find the beautiful 17th week here in India now.

Will be using it with a DFI Nf4 Ultra-D

Will be cooling it with a XP90 or a SI120.

Wanted a 3000+ Venice which will atleast OC till 2.9Ghz

Please Guys i am completly relying on you guys for this info.
Also if its posted in some thread please post the thread that would also be useful.

Earlier i had seen a Venice Core Database thread where many people with there
15,16,17,18th week venice had posted there max oc's on air , water & ln2.


I can get you about 40 (yeah 40) 0517APAW for $219 USD/each if you really want, i'm sure shipping to india is no problem.

http://img487.imageshack.us/img487/3433/2853bestsp32m8vf.th.jpg (http://img487.imageshack.us/my.php?image=2853bestsp32m8vf.jpg)
http://img487.imageshack.us/img487/6070/2898mhzsp1m5eo.th.jpg (http://img487.imageshack.us/my.php?image=2898mhzsp1m5eo.jpg)
http://img324.imageshack.us/img324/6473/2763primestable3cq.th.jpg (http://img324.imageshack.us/my.php?image=2763primestable3cq.jpg)

[ALXgr]

hawkeyefan really nice chips you got there!!!
2.7-2.8 with only 1.65Volts and ONLY for 217US$.... :stick: :stick:

Anyway...Not my business

Take a look at this chip.Its a decent overclocker but cant get high enough for me:( waiting for opteron 146 CABYE 0540 :woot:

Venice 3200+ 0517 BPEW
24/7 stable @2820 1.48V
Bench @ 2930 1.61V [Vcore is a bit higher than it really needs]
OCZ pc4800 platinum ltd edition @ 1:1
IMC tested @ 9x300 2.5-4-4-10 1T

Take a look some pics [random cpu speed]

29sec Spi 1Mb [I need some BH/UTT ASAP:)]
http://img142.imageshack.us/img142/767/10x2939fl.th.jpg (http://img142.imageshack.us/my.php?image=10x2939fl.jpg)

Sandra arithmetic 10x290 [Memory 1:1]
http://img481.imageshack.us/img481/866/10x290sandraarthmetic0uk.th.jpg (http://img481.imageshack.us/my.php?image=10x290sandraarthmetic0uk.jpg)

10x282 S&M stable
http://img481.imageshack.us/img481/1189/28208ft.th.jpg (http://img481.imageshack.us/my.php?image=28208ft.jpg)

10x280 1:1 [4+ hours Memtest error free]
http://img256.imageshack.us/img256/2003/10x280memtest6uq.th.jpg (http://img256.imageshack.us/my.php?image=10x280memtest6uq.jpg)

[mascaras]

hi guys, i have a 3200 venice DH-E6 for what i read this steping suks but mine its ok , i can get 2500@vcore default and max stable 2750mhz@1.6v -

PICS:

>>2500@vcore default :--http://img278.imageshack.us/img278/1702/140v6xt.th.jpg (http://img278.imageshack.us/my.php?image=140v6xt.jpg)


>>2800@1.63v:-- http://img19.imageshack.us/img19/5377/28001lh.th.jpg (http://img19.imageshack.us/my.php?image=28001lh.jpg)

[hawkeyefan]

hawkeyefan really nice chips you got there!!!
2.7-2.8 with only 1.65Volts and ONLY for 217US$.... :stick: :stick:

Anyway...Not my business




hehe, I've seen people pay a lot more for a lot worse. look at it this way, I got an (almost) stock FX-57 for ONLY 219$ ;)

also those are not "my chips", the only time I've ever dealt with the retailer who has them is to buy this single chip

here are best benchies so far, also figured out that I was using too much voltage to get stable at 2763, memtest was passing in DOS but found out the hard way it was not Windows stable...you live and learn

SP 512K 2907mhz @1.678v. Can get SP1M @2989mhz but not higher. bah.

http://img463.imageshack.us/img463/3301/2907sp512k7rq.th.jpg (http://img463.imageshack.us/my.php?image=2907sp512k7rq.jpg)

stable 2700mhz @1.534v

http://img463.imageshack.us/img463/3474/2700priming20hours3rz.th.jpg (http://img463.imageshack.us/my.php?image=2700priming20hours3rz.jpg)

SP32M at my 24/7 settings. hehe, go crappy value ram! :cord:

http://img463.imageshack.us/img463/6695/2700225sp32m3zo.th.jpg (http://img463.imageshack.us/my.php?image=2700225sp32m3zo.jpg)

[umnik]

http://i12.photobucket.com/albums/a215/umnik/12.jpg

[Pc juice]

My current max on wc:
don't look at voltage ;)

http://img120.imageshack.us/img120/3161/10520pf.jpg

[Celcius]

cpu in sig, xtreme air cooling

http://valid.x86-secret.com/show_oc?id=51242

[Xyus89]

Hi everybody,

I saw that somebody used a sse3 patch,
isn't this cheating or is this always in superpi,
someone just explain it to me please ;)

xyus

[Celcius]

New OC

http://valid.x86-secret.com/show_oc?id=55364

[Burnt_Ram]

New OC

http://valid.x86-secret.com/show_oc?id=55364
how much vcore did you have to throw at it ?

[Lesterp]

http://photobucket.com/albums/b134/lesterp/?action=view&current=3200.jpg

[Celcius]

how much vcore did you have to throw at it ?
about 1.71v-1.72v:(

[stone_cold_Jimi]

3000+ E6, no great shakes but still nice at 2G4. Does 2G5 SPi32 but won't prime. Hits the wall after that; volts make a marginal difference.

http://0wned.org.uk/pics/shots/venice2g4.jpg

[Xyus89]

atm I'm running 2530mhz @1.53, 16 hours prime, (vcore can go lower!!)

just burning cpu in.
but I have to switch to 2T approx 288htt :(
cpu is a 0528GPFW E6 +3000

I'll post a pic once I've reached 2600mhz prime stable at a low vcore. (1.5 I hope)
btw my stress temp is 42 degrees with air atm :) quite good in comparisson with my s754 newcastle what was +60 degrees. after a couple of minutes toast.

Xyus

[stone_cold_Jimi]

Yay! There's life in the olde Venice 3000+ E6 yet. With a Vapo LS, I've been priming at 2.7 GHz, 1.495v dmm reading, -17C to -9C. I tried to go 311 x9 for 2.8 but trashed a Windaz system file on boot - the A8N32 goes a bit funny when booting with the 0.2v overvolt facility apparently, so might have tried initial boot at 1.3v, which is not a winner.

I'll clear down the CMOS tomorrow and see if I can fix it. Still, it's already more than I expected.... 50% OC, just like an E3 ;)

[ChronoDog]

CPU: Venice 3000+ LBBWE (can't remember the assembly date..) @ 350x8 (2800mhz)
VCore: 1.625V (1.45V +10% on my Neo2)
Cooling: Air, SLK-948u + 80mm 3k RPM fan
Temps: 40C idle, up to about 50C on load
System: Neo2 PT (BIOS v1.8NFM 1T mod), PQI Turbo TCCD 2x512 memory
Stability: overnight (about 6 hours) of Prime95

I haven't found a decent setting/divider for the memory yet, so benchies such as SuperPi would be pretty pointless, the memory is at 1:2 right now (175mhz 2-2-2-10 1T).

http://img505.imageshack.us/img505/1517/venice2lk.th.jpg (http://img505.imageshack.us/my.php?image=venice2lk.jpg)

[Hydrus]

Does anyone knows which is the "good stepping" for 3200+ at this moment?

[Hazzan]

My Venice 3000+ can run 2,8ghz vcore 1,475volt with stockfan stable SPi 32m
http://img.techpowerup.org/060109/2,8ghz.jpg

[Serge84]

Does anybody here have a socket 754 Venice?

[Waffentraeger]

Heard someone smth. about 30week Venice? I have it but overclocking is so little - 2600Mhz @1.7voltage by Tt BigTyphoon. I just wanna to by Operon144. Mem Hyndai D43chips 474MHZ 2.5-3-3-7timings.

[stone_cold_Jimi]

Check my sig (old rig). Priming right now at 32C. It's a pretty nice chip; wish I had a better mobo and ram for it, because I'm sure it would really fly. BTW, Vcore is 1.44v.

http://www.0wned.org.uk/pics/shots/s754ven-2.6.jpg

[nachthymnen]

My new 3500+ under cold water(cpu @ 9°)
3030 mhz with 1.648V:
http://valid.x86-secret.com/show_oc?id=63936
SPI 1M @ 2904MHz: (512MB in single channel memory timings not aggressive)
http://img61.imageshack.us/img61/574/spi29047nf.th.jpg (http://img61.imageshack.us/my.php?image=spi29047nf.jpg)
Waiting for VAPO LS.
http://img313.imageshack.us/img313/383/cpuchipset8av.th.jpg (http://img313.imageshack.us/my.php?image=cpuchipset8av.jpg)

[nachthymnen]

Received today my OCZ Gold VX.
A Spi update with iced water:
SPI 1M @ 2926MHz=28.656
http://img385.imageshack.us/img385/7334/spi29267gv.th.jpg (http://img385.imageshack.us/my.php?image=spi29267gv.jpg)

Win XP+SP2

[CyberKnight]

here is a valid...voltage isnt stable , because i have a unreal 300 watt psu.:slapass:

stock cooling , c&q is off , cpu core is about 30 C. if i have a good psu and very well cooling i can pass by 3200 mhz :stick:

Venice 3000+@2970mhz :cool:

http://valid.x86-secret.com/show_oc.php?id=65496

:cool:

[Smy]

i got a 3200+ venice with : LBBWE 0551 BPQW is it a good one?

[arczi]

My Venice 3000+ 0520 EPMW can run:

http://img420.imageshack.us/img420/368/e328001327ak.th.jpg (http://img420.imageshack.us/my.php?image=e328001327ak.jpg)
2809MHz @ 1.320v

http://img96.imageshack.us/img96/7400/e329001381pt.th.jpg (http://img96.imageshack.us/my.php?image=e329001381pt.jpg)
2907MHz @ 1.380v

http://img96.imageshack.us/img96/7613/e330001452ve.th.jpg (http://img96.imageshack.us/my.php?image=e330001452ve.jpg)
3006MHz @ 1.450v

..cooled by Pentagram QC-92Cu :cool:

[Spyrus]

Venice 3200+ LLBWE 0552APHW
1.68V@2.75GHz on stock air.
I will post some results.
Voltage scaling:
1.46V->2.60GHz
1.54V->2.66GHz
1.68V->2.75GHz
Temps with stock air between 38-48 on load & Vcore<1.54

[Spyrus]

For everyday i am at 255 & 1.43V (just to stabilize memory controler).

[stone_cold_Jimi]

My s754 Venice 3000+ is very special. It's a Malaysian one and plainly these are rare - all the others I've seen are Chinese. It's an E6 revision as they all are, so-so in s939 when compared to E3, but pretty damn exciting in s754 I think.

I've been priming at 2650 on a voltage limited Asus board, 1.44v vcore (spec 1.4V), under water with the core showing 29C (Valdiadation 78417 and why don't my link work?), but if I open too many apps or the screensaver kicks in I get a crash. I blame that on the knackered 2 year old Crucial Value sticks myself, must try with the HZ or Ballistix.

What's bugging me is VVJ's assertion that the 13C thermal offset shown in CBiD works as described. 29C - 13C = 16C. If that is true, then this chip must be frickin' amazing. Like very very special. If I had the volts, how far could it go?

Edit: :woot: :woot: this BIOS.. Jeez!! any vcore up to 1.55v gives 1.46v and that's that. Then reading the Anandtech forums, there's a guy who thinks he's got a voltmod which does the same except 1.575 and 1.6 give him more.. just tried it without the voltmod at 1.575 (1012-7 beta BIOS) and got 1.52v / 1.536v fluctating. Priming at 2700 now.. no, 2750 now.. heh, lets keep going... :woot:

[neoman]

Thats very nice for a s754 m8 =)

[stone_cold_Jimi]

Thats very nice for a s754 m8 =)

SPi 32M stable 2800 MHz / 1.63v / 34C indicated constant load.

The wacky K8NE-Deluxe bios goes:

(bios | indicated)
1.5v - 1.550v = 1.46v
1.575v - 1.65v = any setting 1.52v / 1.536v flux
1.675v - 1.75v = any setting 1.616v / 1.632v / 1.648v flux

It primes for a while but fails generally before an hour's passed, 35C constant. Those voltage steps a brutal and there are no tweaks to be had there. I'm trying the RAM at CPU/12 rather than CPU/15 now. This is not a fresh XP build either, like an 8 month old kludge, so maybe a new one would help. And the voltage swings aren't magic fun to be honest.

Validation: http://valid.x86-secret.com/show_oc?id=78529
Screenie (SuperPi finished @ 28m 26s):

[magrichad]

hi guys,

this is my first post on this forum and i must say you guys are pretty decent overclockers, so :clap: to all of you.

I have recently bought a new mobo + cpu and have been playing around with it. It's a venice 3200+ with 0604.. so i think its a pretty new one. I didn't have enough money to buy new memory so i using my current 2x512 corsair 400 MHz and 2x256 crappy 400 MHz. I think i have a pretty decent overclock for 4 memory modules, check it out:

200x10=2000 MHz CPU 400 MHz MEM ( 2.5-3-3-8-2T )
267x10=2670 MHz CPU 450 MHz MEM ( 3-3-3-8-2T )

Vcore is at 1.525 V running 34 C idle and 44 C load on a Zalman 9500CU. Give me your opinion please, i think this baby can run REAL FAST if i had better MEM and only 2 sticks ofcourse.

[Spyrus]

Mine does 2.66 with 1.54V so you are very good up there.
But mine cannot do more than 2.75 with 1.68 which is the max i gave.

[magrichad]

dude your memory is PC3500 mine is 3200, you got 2 sticks of ram i got 4 sticks, i would say , my overclock is better...

[Spyrus]

I did not say that you OC sucks.
I said just what to expect from your cpu with the info you already gave.

[WeStSiDePLaYa]

well, here is my sempy. its based on palermo core which is just a venice core with disabled cache. so i think it belongs here.

SDA2800AIO3BX
LBBWE 0550BAJ

does 363x8=2902 SNM stable.

watercooled. on a dfi nf3.

28c idle, 38c load. average.

[s e t h]

http://flytek.sa3doc.co.za/screens/air3g.jpg

http://flytek.sa3doc.co.za/screens/3gprime.JPG

ada3500daa4bw
cab2e0605fpmw
1422609b60025-t

25' ambient

[stone_cold_Jimi]

That has to be the best 3500 I've seen in ages - 2006 vintage again. :banana3:

[Spyrus]

flytec can you post a 32M?
It will have a good time along with BH.
Which dividers are working?
An A64 tweaker will be helpful.

[s e t h]

:o

http://flytek.sa3doc.co.za/screens/blues.JPG

http://flytek.sa3doc.co.za/screens/3180.JPG

[s e t h]

10x300 with uccc@166
approximate temps
36' idle 70mm fx55fan at 3200rpm
51' loaded fx55fan at 3300rpm
23' ambient
13 hours prime95

[impression]

http://valid.x86-secret.com/show_oc?id=82795

benching now :)

[matt1]

flytek that's one sweet 3500, I thought my 3000 @ 2.7GHz was impressive. Opterons have really stole the limelight, that chip is awesome :toast:

[starostise]

http://flytek.sa3doc.co.za/screens/air3g.jpg

http://flytek.sa3doc.co.za/screens/3gprime.JPG

ada3500daa4bw
cab2e0605fpmw
1422609b60025-t

25' ambient

very nice 3500+ man :)

[matt1]

starostise just seen your 3000 in your signature using 1.6v. What idle and loads temps did you get with it? Mines running 2.7GHz on 1.5v but not sure I'd like to put 1.6v through it... I get idle of 29.C and loads of 41.C at the moment.

[neoman]

Load temps blow 50 is ok . So if oyur temps wont pass 50 C under 1.6v ur safe.
Even little over 50 C wont hurt.

[El Snorro]

I got myself a venice 3000+

it is the one in this picture
http://img132.imageshack.us/img132/6034/dsc015311ir.jpg

I thought 0520fpaw was good, but it just won't do 1m @2,8ghz 1,65v?
aircooled
Any tips?

[starostise]

starostise just seen your 3000 in your signature using 1.6v. What idle and loads temps did you get with it? Mines running 2.7GHz on 1.5v but not sure I'd like to put 1.6v through it... I get idle of 29.C and loads of 41.C at the moment.

it was just max screen for 3024MHz
idle @ nearly 35°C idle and 46-47 @ full
it was prime stable 2.7GHz on 1.32v air, 2.8 1.40v and 2.85 1.45v. but it's dead now :(

check here:
http://membres.lycos.fr/starostise/LBBLE0517DPMW/

[barmanmyk]

3000 Venice
LBBLE 0516GPAW
320x9 2880MHz @ 1.55
VLDT 1.3
VDIMM 2.9
XP90-C/TT 92mm
SilenX 600W PSU
http://img101.imageshack.us/img101/1719/2880air8oa.jpg

How does this stack up?

[Fayt_Leingod]

Gah, looking at all the posts above i feel like i'm going to cry.

0518APMW - 255x10 @ 1.55V - load temps are around 40C, i'd go higher but i've got a crappy motherboard. :P

[shmadz]

NBBWE 0608 GPMW

2820 @ 1.5v 35c - This is 24/7 level. Rock steady at this setting, primes all nite, but more importantly, plays oblivion at max settings 1600*1200 for 16 hours straight on the weekend. (this game is gonna eat my life) --- I don't have a screenie of this setting but I included one of 2800@1.46v (I upped the voltage to guarantee stability and added 2 mhz on the FSB just to get even numbers with the dividers - not sure if that makes any difference tho)
http://img183.imageshack.us/img183/7537/2800at1461vv.th.jpg (http://img183.imageshack.us/my.php?image=2800at1461vv.jpg)

3000 @ 1.7v - 32m prime stable, can't say if it could withstand anything else. There's no way I was gonna run this voltage for hours to test stability/load temps. Hitting 3.0 GHz was like an obsession to me. It ate me up inside until I could think of nothing else. Strangely though, once I hit that magic number I realized how meaningless it is and I will never run that high again with this chip.
http://img183.imageshack.us/img183/3500/3000pi329qp.th.jpg (http://img183.imageshack.us/my.php?image=3000pi329qp.jpg)


Overall Impression -- In a word, WOW. I prefer this chip over my old opty 165. My opty was not the best stepping. It would do 2.6GHz 24/7, but was quite hot and did not run oblivion as well as the venice. Many people rave about the quickness and multi-tasking of the dual-cores but for me, it's a non-issue. I have so many computers lying around that I have one setup for each task. I just moved so my network is completely down (except oblivion - that was priority :D) but my previous setup was one file server that holds my mp3s and movies, One HTPC for the stereo and TV, and one for intensive, time-consuming tasks (burning, decoding etc,) -- why bother with two cores when you can have 2 (or more) whole computers?

[yasoumalaka]

barmanmyk where did get that theme its cool

[Schmetterling]

- MB : A8N-SLI Deluxe
- CPU : A64 3000+ @ 2600mhz (LBBLE 0545XPMW) @ 1.45v running at 32c idle and 34c stressed (Arctic cooling 64 pro)
- RAM : G.Skill ddr400 @ 238mhz 2.5-3-3-6
- GFX : 6600gt SLI setup

Ran 32m SuperPI last night, passed without any problems. Ran 3DMark 01/03 got 22000/16235 points.

3DMark 03 URL: http://service.futuremark.com/compare?2k3=4758786
CPUZ @ 2700mhz: http://valid.x86-secret.com/show_oc.php?id=89432
CPUZ @ 2600mhz: http://valid.x86-secret.com/show_oc.php?id=89547

Lowered the speed a bit for daily use so i won't have to use more VCore.

- Schmetterling

[CompGeek]

LBBLE 0520 (forgot packing code) 3200+

Doing 2550 @ stock voltage, dont know how this stacks up, and Im only using it for 1 day, but I thought I'd post some results, still working my way up to find it's limits, which seem to be high!

[CompGeek]

looks like my limit is ~2575 @ stok voltage, how are Venices doin these days?

[Schmetterling]

Got another 3000+ today, stepping: LBBWE 0611DAG gonna do some testing tonight will keep you guys posted.

- Schmetterling

[stone_cold_Jimi]

Got another 3000+ today, stepping: LBBWE 0611DAG gonna do some testing tonight will keep you guys posted.

DAG? That must be a Chinese (assembly) one, only ever seen it with s754 Venices.

[Schmetterling]

DAG? That must be a Chinese (assembly) one, only ever seen it with s754 Venices.

Indeed, it says 'assembled in China'. Will make a picture of my two cpu's before i mount my DAG.

- EDIT:

CPUZ Validation for 'LBBLE 0545XPMW' (http://valid.x86-secret.com/show_oc?id=89547)
CPUZ Validation for 'LBBWE 0611DAG' (http://valid.x86-secret.com/show_oc?id=89833)
CPUZ Validation for 'LBBWE 0611DAJ' (http://valid.x86-secret.com/show_oc?id=90876)

Just installed the DAG in my a8n-sli deluxe and booted to windows without any problems. Ran SuperPI 1.5 / XS and got 33.687/1m on 2600mhz (289 * 9). Will keep you guys posted.

Upped the HTT to 300mhz, running 300 * 9 now but it seems i need 1.55v to run on this ... ran SuperPI again and got 32.907 so it already improved a bit ... too bad that my G.Skill mem won't do more then 238mhz :( will have a look and see how far i can push this cpu today.

Seems that it will max out between 290/300mhz HTT, for some reason i don't think that the CPU's are causing this as the CPU's are totaly different but do about the same speed. I think my Asus a8n-sli is a piece of crap which is bugging me lol ... time to save some money and go for a DFI and some OCZ mem with TCCD or BH5 :)

- EDIT:

Both the CPU's run stable at 289 * 9 @ 1.45v (I use this so i can use the my ram as 333 so i runs at ~236mhz)

The TCaseMax for both:

'LBBLE 0545XPMW' = 57c
'LBBWE 0611DAG' = 53c
'LBBWE 0611DAJ' = 53c

- EDIT:

Got another one in my hands today (LBBWE 0611DAJ) for a customer of me but it's exactly the same as the DAG. As i promissed here's a picture of the DAG (The DAJ is the same just 1 letter changed)

http://img55.imageshack.us/img55/7963/0611dag8be.th.jpg (http://img55.imageshack.us/my.php?image=0611dag8be.jpg)

All three hit 2600mhz rock solid but until now only the 0545 is known to hit 2700 rock solid aswell. Pushed my memory up to 250mhz yesterday @ 3v with the 0545 running at 2745mhz and hit the 30.812s on SuperPI. Atm i'm waiting for my DFI Expert to come in so i can tweak the mem/cpu a bit more and hopefully hit the 17000 in 3dmark 03 with 2 6600gt's in SLI. (Got until 16867 now)

- Schmetterling

[adidassler]

Anybody here reach 2.8-3.0+ Ghz for DH-E6?
Pls help me squeeze more juice out of my DH-E6 please...

Thanks a Alot, my comes with my Sig...

[Schmetterling]

Anybody here reach 2.8-3.0+ Ghz for DH-E6?
Pls help me squeeze more juice out of my DH-E6 please...

Thanks a Alot, my comes with my Sig...

I'm waiting for my DFI mainboard, should arrive this week, then i will have a look and see how much i can get squeeze out of my 0545 (E3) and my 0611 (E6).

- EDIT:

Btw, you should be able to get you 1M SuperPI at a better time. I've got mine running at 30.8xx thats nearly one seconds faster then you.

- Schmetterling

[ksimp88]

Here are my results:

Athlon 64 3200+ Venice Socket 939
LBBLE E3
1.4v
Stock Cooling Fan from AMD, with a Tt Smart Case Fan II on the side of the case
Specs:
Athlon 64 3200+ Venice
Biostar Tforce6100-939
OCZ EL 512MB/OCZ ELPE 512MB (Dual Channel)
Prime95 stable for 17+ hours
http://valid.x86-secret.com/show_oc?id=99516
http://img240.imageshack.us/img240/2185/2500mhzprime951vj.th.jpg (http://img240.imageshack.us/my.php?image=2500mhzprime951vj.jpg)

[generalkido28]

http://img147.imageshack.us/my.php?image=prime18oy.jpg

here is mine !

[generalkido28]

mine is ada3500daa4bp
lbble 0520epmw
http://img147.imageshack.us/my.php?image=prime18oy.jpg

well i gues the damn link to picture is screwed , i will try to fix it and post it

but basicly mine is running stable with this settings

270x11=2970mhz with mem. 3-4-4-10 at 1:1

i tried in vain to go higher , will boot go to windows take screenie of cpz certification at 3008mhz but not stable either prime or super pi , i was super pi stable at 2999mhz but not prime so 2970 is the best i could get on air , i might try it soon on water to see if it goes higher but first i want to get my 2gig of ocz eb500 mem. then i might get wc !!

[generalkido28]

http://valid.x86-secret.com/show_oc?id=99533

why the hell can't i post pictures or links ? anyone ??!! help !!

[GQJesus]

But here's my Venice - 3000+ @ 2.835GHz. My load temps are normally are around 39C-ish on the Zalman. I've pretty much hit a wall with the chip though at that voltage - I'm not going any higher on air.

http://valid.x86-secret.com/show_oc?id=99672

For Super Pi times, I normally run in the late 31's on 1M. The RAM is really holding me back though; I am about to get some new stuff though (2GB for BF2 :D ) as the final upgrade for this machine.

http://img223.imageshack.us/my.php?image=superpi1m9yf.jpg

I love rockin' the Apple theme :D .

[roadie]

mine is ada3500daa4bp
lbble 0520epmw[
I have a 3000+ with the same stepping as this, which reached 2.5Ghz easily but I was being held back by something else.

I also have a 3500+ LLBWE 0606GPMW, which I need to OC when I get some RAM that doesn't generate errors at SPD timings.

[gOJDO]

My rig:

http://img516.imageshack.us/img516/5855/case6oa.jpg

http://img507.imageshack.us/img507/7954/caseinside2yq.jpg

http://img485.imageshack.us/img485/1141/caseinside23my.jpg

http://img386.imageshack.us/img386/1051/caseinside35pn.jpg

Inside:
ASUS A8N5X NF4 A3Rev2 s939 PCIe
Athlon64 s939 Venice Rev E6 2.0GHz 512kB L2
2x512MB DDR-400 CL2.5 4-4-8 CR2 2.5v Patriot
Creative Labs Audigy 2 6.1
Inno3D GeForce 6600 256MB DDR2 350/700 PCIe
2x160GB Maxtor SATA 7200RPM 8MB Cache
1x120GB Maxtor IDE 7200RPM 8MB Cache
LG DVD-ROM 16x
Sony CD-RW 40x
420W Deluxe ATX 120mm low noise
Cooler Master Vortex all cooper 90mm low noise

Overclocked:
HTT 1120MHz 4x280MHz
CPU 2.8GHz 10x280MHz 1.55v
DDR 466MHz 2.5-3-3-6 CR1 2.8v
GPU 525, VideoRAM 830

Cooling: air
OS: Windows XP Professional x64 edition
http://img504.imageshack.us/img504/6682/cpuz2rc.png

Benchmark results & scores:

Sandra 2005 Proffesional SR3:
- Arithmetic Dhrystone ALU: 13826 MIPS
- Arithmetic Whetstone iSSE3: 6039 MFLOPS
- Multimedia Integer x16 iSSE2: 20854 it/s
- Multimedia Float x8 iSSE2: 32124 it/s
- Memory bandwidth Int Buffered iSSE2: 6846MB/s
- Memory bandwidth Float Buffered iSSE2: 6798MB/s
http://img388.imageshack.us/img388/2628/sandraram5jw.jpg
http://img485.imageshack.us/img485/660/sandramm6wq.jpg
http://img485.imageshack.us/img485/6629/sandracpu6tl.jpg

Everest 2006 Ultimate:
http://img388.imageshack.us/img388/6182/everest2006ultimatecpudescript.png
CPU Photoworxx:
http://img388.imageshack.us/img388/4531/everest2006ultimatecpuphotowor.png
CPU Queen:
http://img388.imageshack.us/img388/7936/everest2006ultimatecpuqueen4pm.png
CPU ZLib:
http://img388.imageshack.us/img388/2343/everest2006ultimatecpuzlib7bv.png
FPU Julia:
http://img388.imageshack.us/img388/8117/everest2006ultimatefpujulia1iu.png
FPU Mandel:
http://img388.imageshack.us/img388/1842/everest2006ultimatefpumandel8p.png
FPU Sinjulia:
http://img505.imageshack.us/img505/176/everest2006ultimatefpusinjulia.png
Memory Latency:
http://img376.imageshack.us/img376/8814/everest2006ultimatememlatency2.png
Memory Read:
http://img510.imageshack.us/img510/9133/everest2006ultimatememread0ia.png
Memory Write:
http://img515.imageshack.us/img515/9826/everest2006ultimatememwrite8wa.png

3D Mark 2005 Professional(1024x768 Trilinear filtering): 3655 3DMarks
http://img516.imageshack.us/img516/5221/3dmark6ei.jpg

SuperPi 1M: 30.813s
http://img525.imageshack.us/img525/8343/superpi1mcpuz6bl.png
http://img518.imageshack.us/img518/4617/monitorspi1mcpuz8lv.jpg

F.E.A.R. (640x480 pixel doubling, low quality):
- Minimum: 168 fps
- Average: 300 fps
- Maximum: 547 fps
http://img504.imageshack.us/img504/3577/monitorfearlowsettings5fi.jpg

[ben rogers]

got this out of my 3500+ Venice - just screenshot stable mind. Needs a lot more vcore.

http://img218.imageshack.us/img218/4118/untitled3ug.jpg

and this super pi run.

http://img218.imageshack.us/img218/2757/31250hw.jpg

[ben rogers]

hi there,

I am running my 3500+ venice at 2907MHz with 1.6v undervolted to 1.586 is this an okay voltage for Folding@home 24/7 or is it risky?

thanks a lot,
ben

[kutujambak]

any NBBWE 0619CAI ?
how does it OCbility?

thx

[Drozdov]

any NBBWE 0619CAI ?
how does it OCbility?

thx

my NBBWE 0609 does 2.5GHz @ stock voltage, stock air cooling.

[kutujambak]

@drozdov
thx for ur reply n info

any other with NBBWE 0619?

[lolhalol]

hi fellow overclockers...im a new member....so tell me what u think of my rig

ADA3000DAA4BW
NBBWE 0618FAB
X100347E60173
Cooling method:
Air with a tt beetle(proc)
Air with hr-05 (chipset)
Vcore:
1.68
mobo:
dfi ut lp expert
ram:
HyperX PC 3200AK2 (2-3-3-6-1T) (KHX 3200AK2) Winbond CH-5
gpu:
winfast px 7800 gt extreme
psu:
fortron epsilon series 600wt
hdd:
wd 80gb


http://img.villagephotos.com/p/2006-4/1169113/Screen82.jpg

[kamran5461]

hey i got easy tune also. but i dont trust to use it. i try to stick with bios oc'ing.

[Drozdov]

A64 3200+ Venice
NBBWE 0609
TT Big Typhoon

2.7GHz @ 1.584v

[Lars Krimi]

sorry, but i cant provide a temp reading.. the result is from jannurary at a little lan party.. we opened the windows and set up an AC.. ambient temp was abuot 7 C* i think.. cpu load was between 24 and 28 C* as far as i remember :)

its a watercooled(waterchill, a bit modified) 3000+, 2 gb ram (~300MHz), 6600GT, DFI NF4 ultra-D

http://j-p-h.dk/venice.jpg

[Max Tractor]

Venice 3200 NBBWE 0608 CPMW - Epox 9U1697 GLI

Venice 3200 NBBWE 0608 CPMW I bought 2xvenice the other was NBBWE 0608 GPMW which can do around 2700(both retail)

2800 is about the max the chip can do

Venice 3200 NBBWE 0608 CPMW - 2800 - 1.6v - 3xHTT - 2x512 corsair VS - 166 Divider - 30.906

http://img125.imageshack.us/img125/7334/venice3200nbbwe0608cpmw280016v3xhtt2x512corsairvs1 66dib7.th.png (http://img125.imageshack.us/my.php?image=venice3200nbbwe0608cpmw280016v3xhtt2x 512corsairvs166dib7.png)

This is what I run it at 247/rosetta stable, scythe ninja/2x1gb pqi/ and Epox 9U1697 GLI bought used from(I think roadie above) 350fsp/seagate 320 7200.10, threw it together for about £260 and dropped in my 79gt, used for gaming/net/and crunch. The epox 9u1697 is a bargain board, and compared to my outstanding epox 9npa+ does not suffer from vdroop, a bios update could do wonders for the 9u1697

http://img150.imageshack.us/img150/9518/2700venice3200nbbwe0608cpmwepox9u1697glijw9.th.png (http://img150.imageshack.us/my.php?image=2700venice3200nbbwe0608cpmwepox9u1697 glijw9.png)

This was an OEM venice I had earlier this year, could not get it stable above 2500 in the neo 2 that I was usuing at the time

Venice 3200 - NBBWE 0608 GPMW - 2900 - OEM



http://img71.imageshack.us/img71/247/venice3200nbbwe0608gpmw2900oemeq6.th.png (http://img71.imageshack.us/my.php?image=venice3200nbbwe0608gpmw2900oemeq6.png )

[gianni-gt]

wow look at this!

0617 TMPW : 3204MHZ Prime-stable! with normal water-cooling. (http://foto.arcor-online.net/palb/alben/69/1887469/1280_3761653333643133.jpg)

not mine... is the cpu of Ronny G. from germany

max cpuz screen was ~3400mhz@1.71V (i doesn't find the link atm)

[Bl4ck^!]

Anybody here reach 2.8-3.0+ Ghz for DH-E6?
Pls help me squeeze more juice out of my DH-E6 please...

Thanks a Alot, my comes with my Sig...

a m8 of mine reached 2.95ghz on 3500+ E6 (did not say if its prime stable ;F)

my E6 3000+ on a crappy ASRock DS2 reched 8X325HTT @1.45V, and 9X300HTT @ 1.55V , waiting for another mobo change ;F or going for X2 3800+

Damn gianni-gt that 3200+ clocked nicely ;>

[erico]

Here are some of my results with a 3500 venice on a DFI ultra D with an xp90.
http://img257.echo.cx/img257/3584/sandramembandwidth4kf.th.jpg (http://img257.echo.cx/my.php?image=sandramembandwidth4kf.jpg)http://img117.echo.cx/img117/4988/250SandraCPU.th.jpg (http://img117.echo.cx/my.php?image=250SandraCPU.jpg)http://img117.echo.cx/img117/7002/3d2.th.jpg (http://img117.echo.cx/my.php?image=3d2.jpg)
http://img117.echo.cx/img117/5716/250SuperPi.th.jpg (http://img117.echo.cx/my.php?image=250SuperPi.jpg)http://img117.echo.cx/img117/7945/2503d03.th.jpg (http://img117.echo.cx/my.php?image=2503d03.jpg)http://img117.echo.cx/img117/983/2503d05.th.jpg (http://img117.echo.cx/my.php?image=2503d05.jpg)
Please give more details including your memory timings,etc. Did your rig test Prime Stable and for how long did you stress test it?
Thanks

[ben rogers]

3246mhz , air cooled, 1.65v. If anyone wants to go phase change test it they're welcome to.

http://valid.x86-secret.com/ccpuz.php?id=135428

[buttmud]

3246mhz , air cooled, 1.65v. If anyone wants to go phase change test it they're welcome to.

stepping?

[ben rogers]

Stepping is:
ADA3500DA4BW
CACAE 0611GPMW

[kemo]

3246mhz , air cooled, 1.65v. If anyone wants to go phase change test it they're welcome to.

http://valid.x86-secret.com/ccpuz.php?id=135428
WOW you got a great CPU mine wont do 2.8 with that voltage

[ben rogers]

Currently the 3500+ is sitting in its box doing nothing as I upgraded it to a dual core....but that screenshot was just the max it can do on air cooling, no matter what - just to click the verify button on cpu-z made it reboot almost instantly.

It was stable at 2.907 GHz 24/7 folding@home, and benchmarking upto 3.05GHz for super pi...needs better cooling :D

the vcore was actually set to 1.7v in the BIOS, but it undervolts big time and speedfan was saying 1.64v IIRC.

[kemo]

mine need actual vcore @1.7 to prime stable @2.8 GHZ but temp never exceeds 48C

[buttmud]

mine need actual vcore @1.7 to prime stable @2.8 GHZ but temp never exceeds 48C

same, but i can only get to 2.7 GHz and my temps get around 45c on a naked core.

[CH3CH2OH]

here's mine...
that's enough for me :)

http://img451.imageshack.us/img451/6150/ads305z9ha4.jpg

[ben rogers]

Hi,

just wondering what the program is you are using to monitor the voltages and temperatures?

thanks

[kemo]

Speed fan is compatible with lots of mobos try it out

[gianni-gt]

btw: venice @ 1.92V still alive = WR

http://octs.ripping.org/dryicesession2/octs/oc/3624.94mhz_with_info.jpg

[coop]

^^ Wow, nice job. That's some chip.

[CH3CH2OH]

Hi,

just wondering what the program is you are using to monitor the voltages and temperatures?

thanks

the program is asus pcprobe 2

[Spacehead]

I have a 3,1 Ghz 3D-benchable Venice 3500+
It is also CACAE :)
exactly cacae0612apmw
http://service.futuremark.com/compare?3dm05=2479910

[i found nemo]

Does anybody here have a socket 754 Venice?


yes, and i'll try to get some pics up i been doin' some tweakin', and i got screen shots and saved the score ( the save option on the results screen ) cuz i have no internet, i'm at my sisters. i think i have the sse3 patch and xs 1.5 version. i want to see the real difference. i will run all pc mark and 3d mark, but dont have 3d mark 06 right now 2.71 ghz 1.589 v's according to cpu-z does not scale very well past that. i'll try to get a few hours of prime too and really pack this thread full of benches like it's supposed to be. managed 22.3k on 2k1 with my 6600gt @ 575/1147-8? mhz. get 64k in aquamark 64.7k i belive? seems my vid card only scores 8k in that and cpu scores 11k, so that means my vid-card is a bottle neck? how about a 7600gt? 600/1600 sounds pretty damn good lol and garunteed to do that just cuz i'll get the xfx one.

[MARyo]

btw: venice @ 1.92V still alive = WR

http://octs.ripping.org/dryicesession2/octs/oc/3624.94mhz_with_info.jpg


:eek: nc :eek:

[MrSeanKon]

btw: venice @ 1.92V still alive = WRWOW!!!! :woot:
Have you found other stable frequincies using a different Vcore?
It will help me much.....
Let me know....

[Mi©hel]

3000+ Venice (LBBLE 0517 BPEW)
DFI LanParty SLI Expert
2x 512 MB Twinmos (no BH-5 or whatever, just budget):hm:
Tagan 550W
Zalman 9500 AM2 @ AS5
Ambient temp ~15C

Max air:
http://valid.x86-secret.com/cache/154314.png
Validation (http://valid.x86-secret.com/cache/154314)
vCore used was about 1.75V

SPi 1M stable:
http://www.amdgeeks.net/overclock/level2/343_2.jpg?nocache=116938312855540400
Validation (http://valid.x86-secret.com/show_oc?id=154809)
vCore used was about 1.71V, with higer FSB and lower MP it reboots.

Prime stable 10hrs:
http://www.amdgeeks.net/overclock/level3/351_3.jpg?nocache=116938318877254000
Validation (http://valid.x86-secret.com/show_oc?id=156076)
vCore used was 1.75V

My board seems to have a FSB wall, it won't go any higher than 365MHz, not even with a lower CPU-MP:mad:
Photo of the rig:
Click (http://i90.photobucket.com/albums/k280/dTw1zzy/P1120154.jpg)

[Spacehead]

I have an important question here (http://www.xtremesystems.org/forums/showthread.php?t=132657) regarding the dividers.

[i found nemo]

more ...

[i found nemo]

more still ....

[i found nemo]

coulda went longer with prime but i had a half day at work and wanted to play css lol

[Spacehead]

Actually my Venice is benchable @ 3.23 Ghz

http://service.futuremark.com/compare?2k1=9143805

[Spacehead]

Actually my Venice is benchable @ 3.23 Ghz

http://service.futuremark.com/compare?2k1=9143805

and prime stable at 3 Ghz
http://spacehead.foppa.fi/3Ghzvakaa/3004MhzPrime16h.jpg

I benched with 3,1 Ghz with CPU-Z as proof:
http://spacehead.foppa.fi/3Ghzvakaa/3100Mhz3DMark2001.jpg

[stingush]

3013 VALID stock AIR! :
http://valid.x86-secret.com/show_oc?id=181755

http://valid.x86-secret.com/cache/181755.png

[antron]

Venice 3000+@3041Mhz - stock AIR (benchable at 2760Mhz)
0521DPMW
XFX 7950GT 570/730 @ 675/900
http://valid.x86-secret.com/show_oc.php?id=164331
4505 - 3Dmark06
http://service.futuremark.com/compare?3dm06=1306105
10293 - 3Dmark05
http://service.futuremark.com/compare?3dm05=2634744

http://img159.imageshack.us/img159/7921/antrona64venice3041mhz1qk1.jpg
I could bench Aquamark at 2900Mhz
http://img71.imageshack.us/img71/8827/aquamark2915mhzcpu67590zy9.jpg
http://img481.imageshack.us/img481/3443/smartguardianct9.png

[Boite de P4]

- 3000+ LBBLE0517 APFW @ 2.86Ghz
- 1.58V
- Water
- near 50°C full loaded
- 2*512Mo Twinmos SP @ 160 Mhz / 2.5-3-3-5
- Prime during 4 Hr

http://img522.imageshack.us/my.php?image=cpuz3000318x9xq2.jpg

[Lancer33]

Was just playing around with my wife's rig.

[kevinbo03]

Wow! some very nice clocks in this thread.

This is the best I've been able to do, Maybe someone can give me some advice:

http://img517.imageshack.us/img517/7228/untitledfe1.png
http://img525.imageshack.us/img525/4791/4r32423452345234gq2.png

Cooling is Thermalright XP-90

[AgentGOD]

This is a little late, but my 3000+ Venice hit 2.6 GHz with only 1.45v. It was also cooled by ThermalRight XP-90 w/ Panaflo @ max (same cooler I'm using for my optie). It hit "only" 46 C after 12+ hours of Prime95 (42 according to Core Temp).

[freakBYnature]

I got a venice LBBLE 0517DPMW...

and I managed to squeese out 2.8 GHz with 1.5V, hasn't tested with lower volts on that speed, but tested higher, dont know if's the cpu that can't handle more, if it's the mobo (ASUS A8N32-SLI DELUXE) that can't handle more HTT (311), or if it's my rotten PSU (Apevia Chameleon/Aspire 550W) that makes it stop. I'm getting a cooltek 600W in just a few days, so that answer will be coming.

I understand that week 0517 is a good week, this was just a cpu I bought really cheap on some norwegian sales forum (for about 30$ or so) and I expected a Winchester so I didn't even test it first, it actually has been lying on a shelf here for somewhere around 90 days now, until today I started checking up the stepping, and found out that it actually was a venice - not a winchester - and e pretty good venice aswell. Clocks about the same as my opteron 170 with this PSU, gets 2.8 Ghz there aswell.

[knopflerbruce]

I'm thinking about buying soem old singlecores, just to OC them (and maybe get some hwbot points if I'm lucky). The problem is that I have NO idea which steppings I should look for for the venice e6's. Anyone?:D

[gianni-gt]

check: http://www.forumdeluxx.de/forum/showthread.php?t=225074

[knopflerbruce]

Hmm, thanks I got some nice info there;)

But I'm also looking for 3500+ and slower CPU's, and they're not included in that database:(

[freakBYnature]

Wow! some very nice clocks in this thread.

This is the best I've been able to do, Maybe someone can give me some advice:

Cooling is Thermalright XP-90

Turn the vcore up to 1.45~1.5 and try turning up the HTT to 270 and higher ;);)

I have mine at 1.5V @ 2.8 GHz

EDIT: Have to edit this one some. On my 3000+ there's only 9x multi, so 2.8 GHz was on this multi, had to go HTT 311 and divider 166/333, but anyway RAM there is on 251~252 MHz or something like that, so it isn't bad either for CPU or RAM. E3 stepping ROCKS! ;)

[BBA]

ive got a couple venice 3200's if you're interested.

asking 20 usd each :)

~BBA

[ben rogers]

3500+ Venice @ 3055MHz
2 x 512MB BH5 @ 218MHz 1.5-2-2-0
Akasa heatsink
1.7v

http://aycu24.webshots.com/image/27823/2000286957891656143_rs.jpg

[stunned_guy]

Hmm, thanks I got some nice info there;)

But I'm also looking for 3500+ and slower CPU's, and they're not included in that database:(

Look at this side but not much different cpu are posted there:
http://www.forumdeluxx.de/forum/showthread.php?t=256238&highlight=stepping

[ser710]

Hey guys I have a 3200+ @ stock and I wanted to experiment with it a little bit. I've never OCed anything before in my life, is there a simple guide around here that shows what you have to watch out for, step by step.

[antron]

Check this guide (from page4 and on)
http://www.madshrimps.be/?action=gethowto&number=4&howtopage=144&howtoID=58

Also spend a bit more time searching this forum for guides. There are plenty! ;)

PD: Which is your motherboard?

[ser710]

I have a T-Force 6100 939.

[antron]

http://www.pcstats.com/articleview.cfm?articleid=1966&page=5

This is the 5th page of a review of your board. It is useful in order to know which possibilities you have. One of the most important things for overclocking is the stability and the flexibility of your motherboard of tweaking (voltages mainly).
It seems that although your mobo is a MicroATX (not usually recommendable for overclocking) has quite decent options to play a bit :)

PD: Maybe we should move this to the hardware section. Create a thread with the name of your motherboard and ask a moderator to move our posts there.

[ser710]

That's the AM2 version, is there going to be a big difference if mine is a socket 939?

[antron]

Not for overclocking (I checked both versions and, what differs in yours is that you have printer port and the version of the on-board LAN and sound chip are different)
Even if not were your motherboard, the rules to play are the same for everyone. Follow the steps you can find in every guide of overclocking:

- Basics
Hardware: to have a solid mainboard an a ROCKsolid PSU)
Software: for testing stability http://www.xtremesystems.org/forums/showthread.php?t=117636 ->please read the whole thread to have wich version is easier/better for you and how to use it
- Find the max stable FSB [HyperTransport in your case] value
- Find the max stable mem value
- Find the max stable CPU value
- Finally adjust the parameters to most optimal for stability or whatever you want to use your OC'ed rig for.

good luck :)