what do you think abaut?

[Giasan]

Hello to all.
I'm italian and exuse me for my english.

I have resch this resoult what do you think about this mem and this cpu?
Can you help me for go over this?

My sistem:

DFI nf3 250Gb
A64 NC 3000+@2565 at 1.9v (285x9)
2x512mb OCZ pc3200 Platinum Rev 2 @285mhz 2.5-3-3-10 1T @3v
1x80gb Imb
1x40gb Maxtor
1xpioner drv105
1xDVD lg
Antec True control 550w
Liquid cooled by Ybris Typhoon
Like this i RS.
SPI 34'

The mem go over, i have reach 320mhz at 3-4-4-10 @3.1 do a sandra mem but is not stable.

Can you help me.

PS: i can't put the shot, but if anybody can i sand to him my shot.

Thank

[Giasan]

other photo

[Giasan]

and other

[$0m#0n#]

WoW, 1.9V :eek:, I am not realy sure 1.9V is safe even on phase change it's a lot.

[Giasan]

WoW, 1.9V :eek:, I am not realy sure 1.9V is safe even on phase change it's a lot.


My temp is good, 29°c on Cpu in idle, full 32 - 36°. My pc still on for day 24/24.

My Psu voltage i think isn't good. I think i must mod.


Can you help for reach some more from the system.

[enzoR]

1.9 will kill it after a while. whats your cooling?

[Giasan]

1.9 will kill it after a while. whats your cooling?


Liquid : Ybris Typhoon + rad

I'have it from two week and i have no problem.

Have you look my temp?

What do you think.

PACE.

[jumanji969]

Its not just temps when you push too many volts through it. This is why even on phase change people can still fry chips. I would say 1.9v is fine for benching for a few hours but not for everyday use, if you want to keep using that chip for a while.

Also don't trust software to judge your psu rails. Get a multimeter and check them yourself, its MUCH more accurate.

[Giasan]

Its not just temps when you push too many volts through it. This is why even on phase change people can still fry chips. I would say 1.9v is fine for benching for a few hours but not for everyday use, if you want to keep using that chip for a while.

Also don't trust software to judge your psu rails. Get a multimeter and check them yourself, its MUCH more accurate.




Hi,

I had many cpu and whit a liquid cooled i dont fry no one of that. All my cpu go whit much volt and it's go good. My last cpu was a Athlon xp -mobile 2500+ that i pusch to 2700mhz and it stay at 2v for 9 months every day. Now i sell this cpu to a friends and it still go fine.
The only think that i fry is a MB (my NF7-S) for vddr mod i think.
I think that with proper cooler the cpu isn't stessed to much.
Another think, how much time you think to hold your cpu?
One year i think is to much, my cpu must gain all the money that i spent for it, considering how many money cost after little time you have bought it. (ex if i buy a a64 for 150€ after a little time it cost 100€, after one year there is new cpu that i want buy)

Thank.

PACE.

[andL64]

nice clock but the S754 dont clocks as good as the 939 winnies :D

nice Sisoft really good ram i think i ordered OCZ rev.2 with TCCD and they only do 260-270 at all *lol* so i send it back....

and no its really not to much vcore i think i gave my clawhamer 3200+ the same 24/7 with water ;)

so i got 3200+ ch 3000+ nc and 3700+ ch

the 3200 does 2,4 all with water....
the 3000 does 2,7 :P
and the 3700 with my machII does 2850 :D with 1,6 vcore but it seems to me it doesnt bring me far forward if i go higher maybe when i ll set to 1,9-2,0V but i havent tried it yet

and i ll wait for the DFI 939 (it comes soOn) and the new E0 stepping or like its called where power consumtpion is 25% less than the winnie got.

but trie lowering the vcore and get some better temps and maybe u ll reach a higher oc

seEn andL

[Giasan]

nice clock but the S754 dont clocks as good as the 939 winnies :D

nice Sisoft really good ram i think i ordered OCZ rev.2 with TCCD and they only do 260-270 at all *lol* so i send it back....

and no its really not to much vcore i think i gave my clawhamer 3200+ the same 24/7 with water ;)

so i got 3200+ ch 3000+ nc and 3700+ ch

the 3200 does 2,4 all with water....
the 3000 does 2,7 :P
and the 3700 with my machII does 2850 :D with 1,6 vcore but it seems to me it doesnt bring me far forward if i go higher maybe when i ll set to 1,9-2,0V but i havent tried it yet

and i ll wait for the DFI 939 (it comes soOn) and the new E0 stepping or like its called where power consumtpion is 25% less than the winnie got.

but trie lowering the vcore and get some better temps and maybe u ll reach a higher oc

seEn andL


Thank, my cpu can do 2600mhz but is better at 285x9 than 260x10. Over not even whit massive volt can do better. This is the first A64 that i have. I have a friends that have a computer shop, so i can test some cpu. I'm looking for a 2800mhz cpu at least.
I have tested a 3200+nc, it can do 2650mhz at 1.60v, over not even whit a massive volt, and it can hit over 300mhz HTT.
Alternative send me yours 3000+ :D.

By, and thank.

What do you think about my psu volt?

[andL64]

do 4 stability of ur ram this:

put 4b Burst length
get L1 drive strenght
and theres something called ....value where u can enter a number till 256 or something get 128 value

*lol* sry man forget the reading points of ALL boards they r crap i got same probs 12V is to low some r too high etc... its false.... get a multimeter and check it by urself on the psu and u ll see....

and theres no matter if u put a noname 300W psu or a 350 chieftec or a 480 tagan always the same ;) so forget this readings....

i dont need the 3000+ anymore if u would like it :D i could send it to ya ;)

seEn andL

[blinky]

the cpu wont die from 1.9v

u guys should go to non-xtreme systems if 1.9v scares you

[Giasan]

do 4 stability of ur ram this:

put 4b Burst length
get L1 drive strenght
and theres something called ....value where u can enter a number till 256 or something get 128 value

*lol* sry man forget the reading points of ALL boards they r crap i got same probs 12V is to low some r too high etc... its false.... get a multimeter and check it by urself on the psu and u ll see....

and theres no matter if u put a noname 300W psu or a 350 chieftec or a 480 tagan always the same ;) so forget this readings....

i dont need the 3000+ anymore if u would like it :D i could send it to ya ;)

seEn andL


Tank again, i test whit multimeter.

Tel me more about your 3000+. ;)

[Giasan]

the cpu wont die from 1.9v

u guys should go to non-xtreme systems if 1.9v scares you


Quote.

[andL64]

its a ADA3000AEP4AX with CBAEC 0430 VPMW stepping

2600-2650 it does under water stable with mach II 2650-2750(max)

but the IHS is still on because i put it off from the 3200+ but with my MACHII i cant get good contact without IHS so the 3700+ is also with IHS it would do 2,9 sure if i ill get him off ;)

the 3000+ isnt boxed its tray and it was cheep and its a good clocker but i like the ch with 1024kB cache the 512kb is it worth :D

seEN

[Giasan]

its a ADA3000AEP4AX with CBAEC 0430 VPMW stepping

2600-2650 it does under water stable with mach II 2650-2750(max)

but the IHS is still on because i put it off from the 3200+ but with my MACHII i cant get good contact without IHS so the 3700+ is also with IHS it would do 2,9 sure if i ill get him off ;)

the 3000+ isnt boxed its tray and it was cheep and its a good clocker but i like the ch with 1024kB cache the 512kb is it worth :D

seEN

Thank for your offer, but your cpu can't do much mhz of mine. For 50mhz i rest whit mine and wait from my friend's shop for the arrival of new cpu that i can test.

Tank again for your offer.

PACE.

[andL64]

no problem!

but maybe can u help me sometime :D

i m searching for a waterchiller/comp.watercooling "review" like a "how to build...." found something but still not good enough!

seEn

[Giasan]

no problem!

but maybe can u help me sometime :D

i m searching for a waterchiller/comp.watercooling "review" like a "how to build...." found something but still not good enough!

seEn


Look this :

http://forum.pctuner.net/forum/showthread.php?s=&threadid=45430



PACE

[andL64]

va bene :D

but i cant understand but found some nice reviews :D

but...thx 4 info!

seEn

[Giasan]

va bene :D

but i cant understand but found some nice reviews :D

but...thx 4 info!

seEn

It's in italian :D :D

If can i help you ask me.

PACE

[Der_KHAN]

the cpu wont die from 1.9v

u guys should go to non-xtreme systems if 1.9v scares you

thats the spirit !! :D