Neo2 (4020 Taiwan)/ OCZ 3200 Rev2 at 280HTT 1:1 (1T)

[Psilonaught1]

Just installed the following: Neo2 (4020 Taiwan)/ OCZ 3200 Rev2, 3500+ (NC)

So far I have been able to get to 280fsb, 1:1 (1T, 2.5, 3,3,5) with the 9 multi, so am pretty pleased with the HTT. Bank Cycle and Dram Timer setting don' seem to be accessable in the bios, how can I edit these - is there a beta bios availabe?

Compared to the rubbish 3200 Ballistix i was using before this ram is a complete revelation. It will SuperPi at this speed with 2.7v, and i'm sure I can get more out of it, just need to burn it in and test different Vmem settings.

CPU isn't that great though, seems to max out at 2.5Ghz with this stock HSF, but will try it with my Mach2 at some later point, and will try my 3200+ next, see how that fairs

http://www.users.globalnet.co.uk/~cipher/Images/3500.jpg

[Vitalizer]

nice! i hope i can run my mems at that speed when i get my MSI neo2..
But are they stable?? i can run sandra memory bandwith test at that speed, but not stable.

[Psilonaught1]

yup memtest and SuperPi 1mb stable - haven't had time for proper testing. Need to burn them in a bit first, plus add a fan to them as they are burning hot :eek:

[funkflix]

OCZ PC3700 EL (0409 Taiwan)

http://people.freenet.de/funkflix/292dual.jpg

[Th3__W00T_GuY__]

283 1T here :) k8n neo2 platinum from korea

[GomerPyle]

Have had OCZ 3200 rev2 at 290 1:1 cas 2,5-3-3-6 with 2.85v at MSI Neo2 (Korea).
No screen as it was just for testing when I had problems with bh-5.

Nice memory you have there!

[Mrki]

2x512 OCZ TCCD

http://mitglied.lycos.de/siedl/0441%20MPMW/9x285_OCZ_2.5_3_3_7_32sekpi.jpg

[fragsta]

2x 512mb OCZ Platinum Rev2
Neo2 ( dunno wich nf3 revision ) , boxcode K0408xxxxxx

http://users.telenet.be/fragsta/OCZRev2/sandramemory.JPG




This shot wasn't 100% stable.
Memtest gives error @ 280mhz. I'm giving 2.75volt, tried 2.85v but it also gave error in Memtest. More volts or just bad sticks?
I've tested te board for high FSB's with mem divider. I did a 24h Prime run with 290mhz FSB so my board isn't the limiting factor.
Anyone an idea to get higher?

[DevilsRejection]

The above two screenshots, are those with 1t?

What does 1t do really, besides make sandra score go up a lot :)

EDIT: Fragsta, why don't you get an ocz ddr booster and give your ram more volts, thats what seems to be your problem. but even then man nice system :D

[Bungo]

What i have understod, 1t/2t is similar to the cpc enable/disable on socket A.
And cpc stands for commands per clockcycle and therefor i get it like u does less commands on the 2t setting and stresses the memory less so u can get higher MHz but since it dosent perform all the commands it could do it losses performance. 2t is more if u got big problems with running 1t.

So 1t is what u should always use.

[aCidbAbY]

nice OC :up:

[fragsta]

The above two screenshots, are those with 1t?

What does 1t do really, besides make sandra score go up a lot :)

EDIT: Fragsta, why don't you get an ocz ddr booster and give your ram more volts, thats what seems to be your problem. but even then man nice system :D

Thx,

don't think the TCCD's need more volt, but you can be right.
It can be the memory controller also

[funkflix]

My one was with 1T and 2,75V! More Volts and the OCZ sucks! Thats an problem ...

[[ r2 ]]

My one was with 1T and 2,75V! More Volts and the OCZ sucks! Thats an problem ...

Not all chips, my 3200 plat rev2s can do prime/super_pi 32Mb pass stable at 277HTT 1:1 at 2.85vdimm, installed the booster, running 3.0vdimm was stable on 285HTT 1:1 havent pushed further.

Anyways ill be getting some 4200 Plats soon :D