Someone with Pentium 4 2.4C + OCZ EL PC4000 Gold?

[higherøx]

Humm???

What are the results?

Here I want 38s in SuperPI but I can't. The best time was 39s, with P4 @3.5 and 292MHz in OCZ 3 4-4-7-8 PAT ON, Performance Mode TURBO.
I have only 2.85v vdimm. Did someone do 292MHz with PAT and Performance Mode enabled with OCZ PC4000 Gold in 2.85v?
It is not 100% stable in my system.

Can somebody help me? I want 38s in spi.
Thank you, I'm learning English so it's horrible.


http://img65.exs.cx/img65/3729/OCZ35GHzPAT39s.th.jpg (http://img65.exs.cx/my.php?loc=img65&image=OCZ35GHzPAT39s.jpg)

[Gogeta]

Not related to a higher OC, but I noticed you had a few programs running in your system tray. Try ending all processes not necessary for Windows including explorer after you have SuperPi open.

[Rodzilla]

Can you run your mem @ 2.5-4-4-7??? That might get you there.

[lalPOOO]

Yea, or a clean install of windows, with all the unnessacary services disabled. I've got the same combo as you, but my ram won't go as far as yours :p: Otherwise I'd compare results.

[Rodzilla]

I think Gogeta and LalPOOO's suggestions will be best.

That should get you to 38 easy. Maybe even better?

What are you cooling with?

[higherøx]

Not related to a higher OC, but I noticed you had a few programs running in your system tray. Try ending all processes not necessary for Windows including explorer after you have SuperPi open.

Ok, I will do it, thank you a lot! :)

[higherøx]

Can you run your mem @ 2.5-4-4-7??? That might get you there.

No it can't. Only with Vdimm mod that I can't do.
;)
In CL2.5 I think I would have to put only +\- 260~265 FSB.

[higherøx]

Yea, or a clean install of windows, with all the unnessacary services disabled. I've got the same combo as you, but my ram won't go as far as yours :p: Otherwise I'd compare results.

Ok :D.
Thank you a lot, I will try what you are talking! :d :**

[higherøx]

I think Gogeta and LalPOOO's suggestions will be best.

That should get you to 38 easy. Maybe even better?

What are you cooling with?

Zalman CNPS7000A-Cu

One time I was running Prime95 for the processor, about 3 hours WITHOUT errors, when I wanted to see MBM5 the system crashes (memory)

This memory can't do 600MHz 5:4 at 2.85v =( (to 3.6GHz)

Thank you a lot.

[Rodzilla]

Bet you could go higher with water cooling! ;)

What kind of temps do you get idle and under load (during prime 95)

Also... are you running 2 installs of Prime95 to test stability?

[Gogeta]

Here's a link to a great site for service tweaking. I gained 1000 points in 2k1 and went from 38s to 37s after following this guide.

http://www.blackviper.com/WinXP/servicecfg.htm

[Rodzilla]

Here's a link to a great site for service tweaking. I gained 1000 points in 2k1 and went from 38s to 37s after following this guide.

http://www.blackviper.com/WinXP/servicecfg.htm

I got 100... Thanks for the tip!

[higherøx]

Thank you a lot, I will try everything but I did 38s I want 37s now ;P
My temps are ~55ºC full load, I didn't run 2 Prime95, only 1

http://img45.exs.cx/img45/2451/OCZ356GHzPAT38s1.jpg

[Rodzilla]

If you are worried about stability then you need to run 2 copies of Prime 95. It will also generate max heat.

Temps seem ok for full load.

Good job on the 38!! :up:

[higherøx]

Thank you.
I want Vdimm mod here. But I don't have any material.

600MHz my memory can't do :D at 2.85v :D.

[lalPOOO]

Have you tried putting a fan over the ram? I find mine gets kind of hot, and with a fan over it I was able to get a couple more mhz out of it. :)

[higherøx]

I dind't try!!

But I don't have a fan, I will look for it :D

[naughty_guy]

great OC you have there. I hvae the same setup as you do. But i didn't have time to do the Vdimm/Vtt mod for my max 3. And my CPU is a crappy one.

[higherøx]

You were not lucky :(

But $hit happens... :( :D

[higherøx]

I can't do 37s
It's impossible because with 300FSB the computer reboots. (memory)

Without PAT or Performance Mode and 3 4-4-8-8, do you know how many FSB can I increase?
I'm using PAT On and Performance Mode Turbo, with 3 4-4-7-8.

T H A N K Y O U

[lalPOOO]

are you talking about booting up at 300? because you can probalby boot a bit lower and then use clockgen in windows. (if thats not what you're already doing)
Also, are you using serial ata drives?