OCZ DDR Diagnostic Booster Works on these Motherboards. [Archive] - Page 2

Tek

01-09-2005, 02:20 AM

I know the OCZ Booster is supposed to run on the K8NS Ultra939, but I haven't been able to do so, until now(I think).

Just need to confirm something:

There is absoluty no chance in hell, my RAM is able to run 215mhz CL2.2.2.8 T1 with only 2.6v, right? They shouldn't be able to, not even at 2.8v(BIOS max).

I think, I finally got the thing to work, so my FX-55 is going to get some RAM power at last. I want 30k with 6800GT within 24hours :)

Naasar

01-10-2005, 05:02 PM

pershoot

01-10-2005, 07:45 PM

that is normal, unfortauntely, for the booster. for me, i variate up to 1.0-1.1. others more (like yourself).

andyOCZ

01-10-2005, 07:52 PM

is it normal for the booster to variate so much during heavy usage? during unreal2k4 it will run from 3.26v to 3.18v. but idle its stays (most of the time) at 3.36v ufff

u basically have to set it so the vdimm doesnt drop under a certain voltage...i think in my case 3.2v

:confused:

The voltage variation you are seeing is due to your PSU reacting to the load. Some PSUs will do this more than others. With a strong PSU you see very little variation.

BeSaiD

01-12-2005, 10:43 AM

Does the Booster work fine on a DFI Lanparty UT?

Thank you.

SteveOCZ

01-13-2005, 08:51 AM

Does the Booster work fine on a DFI Lanparty UT?

Thank you.

Yes but without modding it you can only use 1 stick of ram

Mowgli

01-18-2005, 12:42 PM

hi there...i am new here..juz wana say HELO...n i hav a few questions to ask...

anybody knows bout the compatibility of OCZ Booster with an ABIT IC7? coz i read at the COZ website, saying that IC7 may need VTT mod for better result...n it says using OCZ Booster i can get up to 3.6V...up to 3.6V with or without VTT mod?

how about if i do not want to do any VTT mod? any ideas what cud i expect for my Vdimm using OCZ Booster only?

enzoR

01-18-2005, 12:44 PM

without a VTT mod your rams will not benifit much from more VMEM. you basically HAVE to do a VTT mod.

Mowgli

01-18-2005, 01:13 PM

well..without a VTT mod, how much Vdimm would i be able to get with OCZ Booster?

j0j0

01-18-2005, 01:29 PM

why i cant set the booster above 3v? at 3v my bh5 ram will only run @230fsb but if i set it higher no go @230..... , so the highest volt i can set is 3v specs
msi k8n neo2
3200+

enzoR

01-18-2005, 01:33 PM

well..without a VTT mod, how much Vdimm would i be able to get with OCZ Booster?

you can get as much as you want but your rams will not go higher because of lack of VTT. VTT has to be 1/2 of vmem.

WesM63

01-18-2005, 01:36 PM

Booster works on Gigabyte K8NF-9, however it needs to be modded in order to fit more than 1dimm.

DoGMaN

01-18-2005, 01:37 PM

Anyone had a chance to test the booster with the ASUS A8N-SLI Deluxe?

Mowgli

01-18-2005, 02:10 PM

you can get as much as you want but your rams will not go higher because of lack of VTT. VTT has to be 1/2 of vmem.

hmm..ok...dont really understan that.....looks like i ahv 2 read up more :confused: ...thanx 4 ur replies....

n btw, wat cud i expect from a Mushkin Black Lvl 2 PC3500 (BH5) at juz default of 2.8V? any ideas?

enzoR

01-18-2005, 02:14 PM

around 225 2-2-2.... i'm saying that if your mem does 225 at 2.8, at 3.3 it will be 230 or so if your VTT is not correct. if you have a correct vtt then your mem could reach 250+ with 3.3v.

Mowgli

01-18-2005, 02:26 PM

around 225 2-2-2.... i'm saying that if your mem does 225 at 2.8, at 3.3 it will be 230 or so if your VTT is not correct. if you have a correct vtt then your mem could reach 250+ with 3.3v.

ahh..i think i got u.... :p: can boost the voltage, but without proper VTT, it wont get proper results...yeah..the RAMs i am getting shud be able to do 255 wit Booster....hav a rpint scren fromt he last owner...oh, n i am on Intel btw...

AAdjuster

01-22-2005, 07:44 AM

Is anyone doing the OCZ Booster mod for a fee.

Malachia

01-27-2005, 07:58 AM

guys anyone have tested it on abit AS8???

Bulldog20

01-27-2005, 10:36 AM

guys anyone have tested it on abit AS8???

Yes it works fine, can't say that for the AG8 :(

Cheers

Malachia

01-27-2005, 11:09 AM

thx!!! and i have a rev1 and a rev2 booster, differences???

pershoot

01-27-2005, 11:16 AM

i think the rev. 1 booster had the stick on heatsinks. the rev. 2 (what i own) its just one piece and stuck on very well (you cant move it).

Malachia

01-27-2005, 11:19 AM

well, then rev1 is as good as rev2, no big differences...

ah, on AS8 max volts that i can power on?

Gamer

01-27-2005, 11:42 AM

Does the booster works on Gigabytes 8IK1100 (rev1.0) ?

flo850

01-29-2005, 02:03 PM

you can get as much as you want but your rams will not go higher because of lack of VTT. VTT has to be 1/2 of vmem.
ok
I understand why I can't push my BH5 above 240 Mhz, even @3.6V my VTT stays at (VDDR in bios) / 2

I have to mod my IC7 :(

Ulti

02-01-2005, 07:21 AM

My Booster just arrived and it works great on my DFI nf3! I've it installed in slot 1 with RAM in both 2 and 3. There is just one thing I wonder, I set it to 3.1V, but my DFI says it's giving 3.51V! Wich reading should i trust more?

Malachia

02-01-2005, 07:24 AM

i think no one, you must find reading point and check with a tester...

Ulti

02-01-2005, 07:37 AM

I've a multimeter lying here, I'll look for the reading points.

I have a bigger problem now. The ram cannot run at 200mhz anymore :S When I used the load optimised settings option my ram runs at 100mhz with 2.5-3-2-5 timings! Anyone got a solution?

Ulti

02-01-2005, 10:39 AM

Is anyone doing the OCZ Booster mod for a fee.

My rev2 works without modding it. I can just put in into dimm #1

Ulti

02-01-2005, 11:11 AM

After a lot of testing i noticed the following:

Using the DDR Booster in dimm 1 with ram in # 2 and 3 is possible. This way the DFI won't be able to run 200 mhz. Using the Booster with 1 dimm is possible and works perfectly. Running ram in dimm 2 and 3 doesn't work either at 200 mhz.

Now to find a solution...

Doctor Carta

02-07-2005, 06:59 PM

so i guess the booster doesnt work on the DFI Ultra Infinity II? :(

zoom314

02-09-2005, 12:42 PM

Now this is a real shot in the dark, Does anyone know If the the DDR Booster will work with the MSI K8T Master2-FAR? It has voltage adjustment up to 2.65v only.

andyOCZ

02-09-2005, 06:10 PM

Now this is a real shot in the dark, Does anyone know If the the DDR Booster will work with the MSI K8T Master2-FAR? It has voltage adjustment up to 2.65v only.

Considering that board has a 24 pin connector for the PSU main lead and the booster is only 20 pin compatible, I would say not.

Then there is the issue that no one has tested to see if the board will fail. Yikes!

zoom314

02-09-2005, 06:47 PM

Considering that board has a 24 pin connector for the PSU main lead and the booster is only 20 pin compatible, I would say not.

Then there is the issue that no one has tested to see if the board will fail. Yikes!

Funny thing is I use a 20 pin EG465P-VE(WC) Enermax 460w power supply and the motherboard is 20pin compatible. So I dare say You don't know much about this motherboard. Just My :2cents:

andyOCZ

02-17-2005, 12:20 AM

Funny thing is I use a 20 pin EG465P-VE(WC) Enermax 460w power supply and the motherboard is 20pin compatible. So I dare say You don't know much about this motherboard. Just My :2cents:

Hmmm. quite possible. Must have it mixed up with another board. Sorry

The Enermax more than likely will not work with the booster. Most models have no -5v line or just don't seem to work.

Kunaak

02-21-2005, 07:45 PM

UPDATE 2-21-2005

all motherboards listed in this list have been mentiond to work by someone in this thread. the official list can be found at OCZ's website, this is a unofficial list, just user feedback.

MSI

k8n neo platinum.
K8N Neo2 Platinum

Epox

8RDA
8RDA ver. 1.1
8RDA3+

Abit.

Abit NF7-s rev2 ??
AN7
IS7-e
IC7-G (worked for some, but not for me)
Av8
AS8

Gigabyte.

K8NS pro
K8NSXP-939
K8N nonPRO
K8NSNXP
k8Ns Ultra 939
GA-K8NF-9

Asus.

P4C800-E
A7V880
P4C800 Deluxe
k8n-e
SK8V
A8V

DFI

DFI nForce2 Lan Party Rev. A
DFI NF3 Ultra 250 GB.

Random.

Soltek qubic 3801
Chaintech VNF3-250
shuttle an51r

zoom314

02-21-2005, 07:57 PM

Hmmm. quite possible. Must have it mixed up with another board. Sorry

The Enermax more than likely will not work with the booster. Most models have no -5v line or just don't seem to work.

It has both -5v and -12v lines.

andyOCZ

02-21-2005, 11:17 PM

It has both -5v and -12v lines.

As I said some Enermax have worked and others do not. Some that do not work have the -5v rail and have the same model number as those that do work. That PSU has been around a long time.
I wish I could say more.

zoom314

02-21-2005, 11:43 PM

As I said some Enermax have worked and others do not. Some that do not work have the -5v rail and have the same model number as those that do work. That PSU has been around a long time.
I wish I could say more.

What about an Aspire 520w psu? It has 35A on the +12v rail.

TekXoID

02-21-2005, 11:49 PM

Works on the Chaintech VNF4 Ultra.

BuffaN

03-06-2005, 05:26 AM

Asus A8N SLi Deluxe , does DDR Boostern work on that board? or any SLi board at all?

fatfreepork

03-08-2005, 01:05 AM

Beat_Slayer

03-08-2005, 12:20 PM

What about an Aspire 520w psu? It has 35A on the +12v rail.

It will work as long as that PSU has -5V and -12V!

Enermax had two lines of PSUs, normal ones and noisetakers!

The Noisetaker serie has two 12V rail and no -5V and -12V rail, so in this ones the booster wouldn't work!

BTW, AFAIK it works, but the LCD doesn't, as it is the only thing that needs the -5V line!

zoom314

03-08-2005, 01:37 PM

It will work as long as that PSU has -5V and -12V!

Enermax had two lines of PSUs, normal ones and noisetakers!

The Noisetaker serie has two 12V rail and no -5V and -12V rail, so in this ones the booster wouldn't work!

BTW, AFAIK it works, but the LCD doesn't, as it is the only thing that needs the -5V line!

Don't forget there is also the Whisper Cool series, If that makes any difference at all that is.

b|lly

03-10-2005, 04:38 AM

I have Ic7 max3 no mods and have problems with booster.

I set voltage to 3.35(shown in bios) but when i go in windows and stress memory voltage drops do 3.23.

Is there a way to fix this or i have to do the vtt mod?

gsan

03-15-2005, 12:00 AM

sorry for asking stupid question.

I'm using abit nf7 v2.0.I did the vdimm mod and manage to get 3.26vdimm. It's seem not enough to feed my bh5 especially stressing the ram, the vdimm drop to 3.22v!! So, i'm going to buy a ddr booster. I just wonder that if i install the ddr booster on my mobo, does the high vdimm (3.26v) will kill it?since i did the mod that cannot adjust the vdimm.

andyOCZ

03-15-2005, 12:06 AM

I think you will be ok. Hopefully there will be no problems with the mod and the booster. You will get what the booster can put out, usually about 3.8v max. I think I would remove the mod if it were my board.

gsan

03-15-2005, 12:12 AM

thanks for your replied!! the main problem is i gotta unplug all the hardware if remove the mod and it's very trouble for me. :P

i wonder that if the ddr booster provided 3.8v max to the ram, does itself(ddr booster) also running 3.8vdimm?

one more question,
"Power supplies used in conjunction with the DDR Booster must support a -5V line in order for the LED readout to function."

i'm using Acbel 450W PSU and i got 3.5v for -5v!! Does it make the LED cannot function well and bring any effect to the ddr booster??

http://img.photobucket.com/albums/v235/gsan_bot/acbel450w.jpg

Millyons

03-15-2005, 05:41 AM

gsan

03-15-2005, 06:07 AM

huh? do you mean that if i get ddr booster, maybe i cant even get the vdimm higher than the mod vdimm?

d3birth

03-25-2005, 10:13 AM

Anyone wondering if the booster works with a soltek k8tpro may be happy to hear that over on the Anandtech boards there is a thread concerning the mobo and a rep of Soltek over there has gotten in contact with OCZ about the issue. OCZ should be sending or testing the booster soon.

...at least I'm excited to know.

j0j0

04-05-2005, 03:19 AM

hi i have a question : why my booster gives me only 3.0v? i'm using a msi k8n neo2 , 2*256 bh5 ram , is my psu limiting me? its a fortron 350

[timko]

04-06-2005, 03:12 PM

I've used a booster previously on my NF7-s v2.0 in slot 1, the one NEAREST to the CPU, and had to remove the bottom mosfet heatsink for it to fit.

I increased the vdimm using the booster and noticed the following program reported the increases accordingly...

http://www.hasw.net/8rdavcore/

...and also in the Hardware Doctor program that seems to get shipped with most Abit boards.

Does this mean that VTT tracking is ok on my mobo? :)

andyOCZ

04-06-2005, 05:30 PM

hi i have a question : why my booster gives me only 3.0v? i'm using a msi k8n neo2 , 2*256 bh5 ram , is my psu limiting me? its a fortron 350

You need a good 500w PSU to get the most out of that. A 350w is too small. Time for an upgrade.

jiff

04-06-2005, 07:14 PM

Anyone (maybe andyOCZ ;) ) Tell if this pot is ok to change from original

http://uk.farnell.com/jsp/endecaSearch/partDetail.jsp?SKU=351593&N=401

Cheers Guys :D

andyOCZ

04-06-2005, 07:59 PM

Anyone (maybe andyOCZ ;) ) Tell if this pot is ok to change from original

http://uk.farnell.com/jsp/endecaSearch/partDetail.jsp?SKU=351593&N=401

Cheers Guys :D

http://www.xtremesystems.org/forums/showthread.php?t=48617

Check that out. Of course it will void your warranty. I believe you need a 10k pot. Don't try and substitute.

jiff

04-07-2005, 02:50 AM

Thanks Andy,

Silly billy me linked to a 5k pot I did mean 10K, would the same pot as link but 10K be ok

cheers

RacerX

04-07-2005, 11:18 AM

Hi all. Has anyone else noticed under serious load like Prime or SuperPi your 3.3v line goes crazy. Example, I set my booster at 3.4v while stressing it fluctuates as low as 3.3v. I have a good PS look in sig but its a 2 year old model. It has pots and have the 3.3v line maxed.

Wondering if I ditch the booster and try a OCZ Powerstream 520 with a modded DFI LP UT 4v dimm bios my vdimm will be more stable. Any thoughts?

jiff

04-07-2005, 12:06 PM

Well the cheaper option is to change the pot, which does give more stable voltage.

I would check your psu 5 volt rail when priming to see if its that thats flutuating.

Ubermann

04-07-2005, 02:20 PM

Read about the mod on the booster droop mod thread.
Persivore did an exellent job on it.
I did it and it drops as max 0.01V under load.
But your warranty says bye bye.

nFo

04-13-2005, 06:53 AM

DDR Booster works on: Asus P4P800-E Deluxe
2,7 - 4,2v
Load: 2,6 - 4,1v :woot:
Voltage in Bios: 2,55v

andyOCZ

04-13-2005, 03:30 PM

Great!

gsan

04-14-2005, 05:31 PM

andyOCZ, izzit how far the booster can support on mobo also depend on PSU ? i heard some of them said that booster can up to 3.9v on Abit NF7.

zt_lee

04-19-2005, 02:13 AM

so what's the deal with OCZ Booster nad MSI Neo2 Platinum NF3 mainboard?
maximum 3.4v - that what is says on the CZ website. but i see people giving even 3.8v... do they boot @ 3.4v and then adjust to > 3.4v once they are in Windows???
dont care about it, i am using AI 7 where the website state only get 3.4vdimm. but now i able to get 4v vdimm, that's rocks.... go for it, u wont regret.

gsan

04-29-2005, 05:47 PM

i wonder, why when i set the booster up to 3.6v, my pc cant boot already? i mean the pc seem not enough power to boot it.

andyOCZ

04-29-2005, 07:35 PM

gsan, what is in your system? What PSU do you have?

gsan

04-29-2005, 11:48 PM

AMD M-barton 2400+, NF7 v2.0, Acbel 450W PSU

desert_eagle

05-03-2005, 04:48 AM

Does anybody know, if the DDR Booster works on the Gigabyte GA-K8NXP-SLI? :stick:

Byron

05-04-2005, 02:40 PM

abit IC7-G rev 1.1, issues with prime95... anything more than 2.9vdimm and prime will fail with relative memory error "rounding was 0.5, expected less than 0.4".

B

sin0822

05-04-2005, 06:08 PM

I dont know if this has been posted, but i can get my AS8 to 3.85 or 3.95 i cant remember. UGURU wil only show till 3.5, but i measured with a vdimm and it does go higher, also the booster stabilizes some of the fluctuation of the vdimm, not much but i thought i would add it.

zt_lee

05-07-2005, 05:15 AM

jrw

05-15-2005, 04:39 AM

kingpin confirms P4P800SE @ 3.6vdimm

http://www.xtremesystems.org/forums/showthread.php?p=862056#post862056

pyridoxine

05-16-2005, 12:46 AM

hey guys, whats the max vdimm can the booster support on Abit IS7-E and on which slot should i put the booster??

adrian

05-16-2005, 04:01 AM

Hello...

Does OCZ Booster works on Asus A8N-SLI Deluxe? I saw it has a little problem with that heatsink, but i'm interested if it works?

thanks...

gsan

05-16-2005, 07:30 AM

hey guys, whats the max vdimm can the booster support on Abit IS7-E and on which slot should i put the booster??

should more than 3.4vdimm :)

zt_lee

05-16-2005, 07:43 AM

hey guys, whats the max vdimm can the booster support on Abit IS7-E and on which slot should i put the booster??
try to do some search.. i heard is7 e doesnt support ddr booster...

pyridoxine

05-16-2005, 08:32 AM

try to do some search.. i heard is7 e doesnt support ddr booster...

turn to the 1st page la :confused:

Vassili

05-17-2005, 01:29 PM

DFI

DFI nForce2 Lan Party Rev. A

Does that mean that a DFI Infinity nForce 2 also works with the booster? Or do I have to mod the board/booster?

MAValpha

05-17-2005, 08:44 PM

zt_lee

05-22-2005, 11:38 PM

turn to the 1st page la :confused:
turn to first page??? what do u mean?

FLDQUY157

05-23-2005, 12:54 AM

Does that mean that a DFI Infinity nForce 2 also works with the booster? Or do I have to mod the board/booster?

It coould mean that only the Rev A not the Rev B. I got the rev B, though.

Vassili

05-23-2005, 09:47 AM

It coould mean that only the Rev A not the Rev B. I got the rev B, though.
And does the booster work?

stealth17

05-28-2005, 09:33 PM

please add DFI nf4 all models to the list

thanks

babyelf

05-29-2005, 05:31 AM

and 3.8v for the DFI :)

andyOCZ

05-29-2005, 11:33 AM

please add DFI nf4 all models to the list

thanks

Yup, the DFI NF4 was fully tested by myself and added to the OCZ Compatabilty list with full notes for operation:

http://www.ocztechnology.com/displaypage.php?name=DDRBoostermobocompatibility

justwOo

05-29-2005, 11:36 AM

Does the DDR booster keep our ram safe at night against the even the toughest of foes(the 5v rail on the dfi nf4's?)

corvus_corax

05-29-2005, 12:41 PM

I'm reading about compatibility with DFI NF4. I have a PowerStream 520W (old ones, not like the last revision) and this PSU have a unique 24 pins connector, is there any way to connect it? any adapter :D?

stealth17

05-29-2005, 02:25 PM

Yup, the DFI NF4 was fully tested by myself and added to the OCZ Compatabilty list with full notes for operation:

http://www.ocztechnology.com/displaypage.php?name=DDRBoostermobocompatibility

will it go above 3.8v?

andyOCZ

05-31-2005, 01:36 PM

will it go above 3.8v?

It should, yes. Why you would need that I dunno. :slapass:

Probmaker

06-08-2005, 02:34 PM

does the booster work with the Gigabyte K8NXP-9?

greetz

stealth17

06-08-2005, 02:36 PM

It should, yes. Why you would need that I dunno. :slapass:

XtremeSystems man! :woot: :banana:

andyOCZ

06-08-2005, 04:31 PM

XtremeSystems man! :woot: :banana:

Almost forgot where I was posting! ;)
:slapass:

Gamer

06-29-2005, 05:38 AM

does it work on the Epox EP-9NPA+ SLI ?

Gamer

07-02-2005, 12:39 AM

NO, it doesn't :)

glad that Epox support is up to date...

Kunaak

07-02-2005, 12:53 AM

this is the most up to date list, as of July Second 2005, from the feedback posted here in this post.

MSI

k8n neo platinum.
K8N Neo2 Platinum

Epox

8RDA
8RDA ver. 1.1
8RDA3+

Abit.

Abit NF7-s rev2
AN7
IS7-e
IC7-G (worked for some, but not for me)
Av8
AS8

Gigabyte.

K8NS pro
K8NSXP-939
K8N nonPRO
K8NSNXP
k8Ns Ultra 939
GA-K8NF-9

Asus.

P4C800-E
A7V880
P4C800 Deluxe
Asus P4P800-E
P4P800SE
k8n-e
SK8V
A8V

DFI

DFI nForce2 Lan Party Rev. A
DFI NF3 Ultra 250 GB.
DFI nf4 all models

Random.

Soltek qubic 3801
Chaintech VNF3-250
Chaintech VNF4 Ultra
shuttle an51r

babyelf

07-02-2005, 04:40 AM

any idea about the abit an8?

stealth17

07-02-2005, 10:39 AM

any idea about the abit an8?

it wount work :(

babyelf

07-02-2005, 10:45 AM

hmm ok.. =/

u tired it before?

stealth17

07-02-2005, 11:15 AM

hmm ok.. =/

u tired it before?

opps sorry i was thinking you said a8n...not sure about the an8

too many wierd number and letter codes. should stick to lan party or something easy to rememeber :p:

Nohto

07-02-2005, 01:36 PM

Andy, or anyone else for that matter. What about a MSI K7D-Master running 2 1800+ @ 2400MHZ each and 2 gigs of Kingston non registered ram. That leaves 2 slots open.

ShawnMcGrail

07-02-2005, 02:57 PM

Any word about it for the Asus P4S800?

ShawnMcGrail

07-02-2005, 07:00 PM

Bump?

eBoy0

07-04-2005, 12:11 AM

Don't know if it was mentioned, but it works on the DFI Nf3 Ultra-D, self tested :)

Nohto

07-09-2005, 10:21 PM

Andy, or anyone else for that matter. What about a MSI K7D-Master running 2 1800+ @ 2400MHZ each and 2 gigs of Kingston non registered ram. That leaves 2 slots open.

bump

BB mods's

07-11-2005, 04:08 PM

Any new's on the dfi-875p-t and high voltages?

andyOCZ

07-12-2005, 01:58 AM

Andy, or anyone else for that matter. What about a MSI K7D-Master running 2 1800+ @ 2400MHZ each and 2 gigs of Kingston non registered ram. That leaves 2 slots open.

I do not personally recall anyone testing this board. I did find this: http://www.ocforums.com/showthread.php?t=320663

So somone at OCZ must have had word form a user or tried it. Apparently VTT won't track, rendering the extra voltage useless.

Sorry

Nohto

07-12-2005, 12:29 PM

Ok, thanks for letting me know.

ShawnMcGrail

07-12-2005, 02:41 PM

Okay, Well the Asus P4S800 works for up to 3.9v on no-name RAM Via 12 minutes ago. :woot:

andyOCZ

07-13-2005, 12:03 AM

Okay, Well the Asus P4S800 works for up to 3.9v on no-name RAM Via 12 minutes ago. :woot:

Very good to know. Thanks!

BB mods's

07-16-2005, 02:21 PM

Any new's on the dfi-875p-t and high voltages?
bump

mare87

07-18-2005, 06:49 AM

has any one tried running the booster on Epox 8rda+ rev. 2.0?

I would like to know...

Regards

RocKer

07-18-2005, 07:42 AM

has any one tried running the booster on Epox 8rda+ rev. 2.0?

I would like to know...

Regards
Is it 8rda+ rev 2.0 or is it 8rda3+ rev 2.0,becaus if it is 8rda3+ then the booster works on it,only 3.4v thoug.

mare87

07-18-2005, 09:21 AM

it is 8rda+ rev 2.0

SoF

07-21-2005, 05:49 AM

Abit NF8 WILL NOT FIT. Picked one up at CompUSA- first slot has a cap too close to the DIMM, second slot means that the Booster is blocking the first. Board went back same day.
Didn't trying bending anything, didn't want to risk the board or Booster.

Damn you Abit, why couldn't you be normal and put in three slots?!?! *Shakes fist angrily*

if it's only this - just turn the poti to the other side or where ever you want.
my ones modded in this way to fit in the 4th slot of a k8nxp-9/k8nxp-sli.

was nicht passt wird passend gemacht, ist doch nicht so schwer ^^

Gauss

07-21-2005, 04:47 PM

What about a Gigabyte motherboard with nforce4? The K8NXP-SLI. Is it compatible? This mobo sucks for Vdimm so it would be nice to use the Booster with it.

mare87

08-06-2005, 03:03 PM

I have a question for Andy or someone at OCZ. Why is Leadtek`s K7NCR18D board on your page marked as N and on my Chart which came with the booster marked as compatible? So the booster works with Leadtek K7NCR18D Pro and Pro 2 boards or not?

sja360

08-07-2005, 12:09 PM

anyone confirm the ocz booster rev1 or 2 works in the asus a8v rev2 deluxe?
i've read all 15 pages and there's not one saying "yes the booster and a8v work"

mrlobber

08-11-2005, 11:49 AM

How about the Booster and Asus P4GD1?

BB mods's

08-11-2005, 12:48 PM

Nice suport here. :stick: .has any one else tried the booster on a 875p-t???? i get no post at 3.2v on the booster..ill try again at higer voltages.

Lestat

08-11-2005, 01:22 PM

MSI K8N Neo2 Platinum 3.4V <-- according to OCZ

i can tell you right now the NEO2 will handle 3.6v (tested with DMM on the mobo) as thats as far as i tested with a certain kit of ram...

bb_mod's knows what kit ;)

and BB looks like the 875LE only goes to 3.1v so its possible the PT only goes to 3.1 also.. which just sucks but you also can not use the 24pins with the booster unless you were to extend the length of the other four from the atx plug.

msimax

09-03-2005, 10:17 PM

jetway939gt4 anyone know if the ocz booster is compatible with this mb

TMFX

10-22-2005, 07:19 PM

well, i just grew balls (or REALLY need to sleep...)
OCZ DDR Booster is in and running on my AV8
DDR @ 3.0V and DDR VTT is tracking (reads 1.54V)
upping on the fly...3.3V but VTT is still 1.55...3.4 but 1.5... :upset:

upped (in bios) DDR to 2.8 (max)...booster@3.2V VTT@1.66 :banana:
could be bios setting could be reboot...

not real stable or "Mushie 222 rev 2"s ("new"? TCCD) dont like >3.0V...

be ready to get a fan on your MEM...pups got HOT!

Where is the VTT option of AV8? :confused: :stick:

andyOCZ

10-22-2005, 08:05 PM

Where is the VTT option of AV8? :confused: :stick:

There is no option for VTT. He was saying that as he adds DDR voltage the VTT follows like it should. Some boards will not do this.

Desk-Star

12-16-2005, 07:17 AM

HI!
I was lookin around, and i couldn't find out if DFI Ultra Infinity NF4 is compatibile
with OCZ DDR Booster.

DFI Ultra Infinity NF4 isn't mentioned here
http://www.ocztechnology.com/displaypage.php?name=DDRBoostermobocompatibility

so i wonder, if i can plug in BOOSTER? And if i can , in witch slot?

I would be grateful if someone could answer my question.

Desk-Star

12-19-2005, 02:08 PM

Anybody?:confused:

RyderOCZ

12-19-2005, 09:35 PM

Black Phoenix

04-11-2006, 02:38 PM

But you had tested on DFI nf4 all models, and as i know this board is 24 pin atx. So it's proved that he have to try and then say something, right...

RyderOCZ

04-11-2006, 03:10 PM

But you had tested on DFI nf4 all models, and as i know this board is 24 pin atx. So it's proved that he have to try and then say something, right...AndyT (AndyOCZ) tested on his personal board and found it to work, yes.

Officially, OCZ does not test the booster on any of the 24pin motherboards :)

andyOCZ

04-11-2006, 08:14 PM

But you had tested on DFI nf4 all models, and as i know this board is 24 pin atx. So it's proved that he have to try and then say something, right...

The DFI boards have extra power connectors on the board and handle power differently than most boards. Some boards don't even use the extra 4 pins on the 24 pin at all. Some boards will blow up iof the booster is used. If you try it you could have a bad experience unless you know it is a working combo.

Black Phoenix

04-12-2006, 09:55 AM

I understand, so if i use on my Asus A8N32-SLI i'm at my own... But if it works i can post here right... Let's see if i have the guts to try it...

RyderOCZ

04-12-2006, 10:09 AM

I understand, so if i use on my Asus A8N32-SLI i'm at my own... But if it works i can post here right... Let's see if i have the guts to try it...That is correct :)
It helps also to have a PSU with the 20 + 4 connector, because you can leave the 4 off, connect to the booster harness, plug the booster harness into the mobo, then add the 4 pin directly into the remaining slots on the ATX connector :)

Black Phoenix

04-12-2006, 01:36 PM

Well my PSU is like that kind of config, 20 pin + 4 pin. So part of the test is done...

Black Phoenix

04-29-2006, 12:42 PM

As i had said, i had tested on A8n32-sli... Results: voltage corrected detected, waiting for new memory to test (OCZ VX). For the ones that want to help me, use slots a2 and b2, if ddr don't interfear with ocz resistor... Possible dual channel problem because of the layout (slot a1 - capacitator interfear with ocz heatspreader)...

OverCool

06-22-2006, 08:31 PM

Did OCZ DDR Booster running fine on DFI CFX3200 ATI RD580 mainboard??

Or just use the onboard 4V jumper. Which 1 is more stable?

phi|os

06-22-2006, 10:22 PM

What is this booster?

Black Phoenix

06-25-2006, 01:46 PM

What is this booster?
This is the booster: http://www.ocztechnology.com/products/power_management/ocz_ddr_booster_diagnostic_device

gsan

01-06-2007, 06:42 PM

FYI,

Booster works on DFI NF3 Ultra-D.

Kinsy

01-11-2007, 05:29 AM

FYI,

Booster works on DFI NF3 Ultra-D.
If it does, how?

Think i have rev1.1 - never used it with my OCZ 3700EB as it never worked.

Hooked it up to slot1 with 2&3 holding the memory.

On power up, it displays 25..26...27...28...29...got to 31 and i switched off. I set voltage to 2.6v in BIOS and was worried when i saw it steadily climb. No VGA signal was produced (i.e. no boot). Take it this is the voltage readout?

Got an OCZ Powerstream 520w for it.

As my 3700EB doesnt seem to clock well at all anyway over 220mhz fsb i doubt itll make much difference, but thought id give it a try.