bh5 steppping database

[pershoot]

adding to the thread database:

KHX3200K21G

one stick - no tiki man symbol - 1213209 - 2.5v - assembly in usa

other stick - 1352747 - 2.6v - assembly in usa - tiki man symbol

both 9905193-013.a01

what cpu-z reported (about week of production):
http://indabasement.com/2.5v.jpg
http://indabasement.com/2.6v.jpg

in dimm2 i have the 2.6v labelled stick and in dimm3 i have the 2.5v labelled stick. im assuming cpuz used dimm3 for the dimm slot away from the cpu and dimm1 for dimm2 slot (i have the booster in dimm1). otherwise the label name is wrong on my pics, hehe.

board: NF7-S Rev. 2

prime happy:
2.9vdimm, 2-2-2-11, 2T, 2x512 in DC, ~229-230
3.2vdimm, 2-2-2-11, 2T, 2x512 in DC, ~241-242

i havent tested each stick individually.

hope that helps:)

A64 s939 Winchester in DFI Ultra-D: 1.5(CL)-2(tRCD)-3(tRP)-5(tRAS), 3.4Vdimm, 250, prime is happy. 250-251, 1.5-2-2-5, memtest is happy. using same sticks that were in the nf7 (above quote).

[Mauri Antero]

With intel managed to drive 272Hhz fsb 1:1 with my pair of khx3000 sticks
http://valid.x86-secret.com/show_oc?id=7653
SuperPi 8m also went through

[Rub87]

Not bad for pc2700 sticks :D

[Crimson_dAWN]

Saaya, i've promised you some screen...
Here they are :D :D

306WE A-Data PC3200 Winbond BH5 chips 4x256MB

http://xs21.xs.to/pics/05121/BH5_275.JPG

Cl2 5-2-2 1T dual channel Enabled (but Clock gen covers the "CpuZ scree :( ) 3.36 volts on an EpoX 9NDA3+ rev 1.0 (nForce3 Ultra) modded (thanks to Bigtoe for help ;) :) ).
I've 4x256MB sticks, if you notice i've installed 512MB (2x256MB in dual), but all of the 4 sticks give the same result.
Now I'm searching for a GOOD Winch (mine doesn't work over 2.2-2.25Ghz.......).
Bye

Crim

[chefnr1]

Corsair CMX256A-3500C2
XMS3502 v1.1
0315086
XMS3500 256MB 433mhz CL2
at 3.8v

http://upl.silentwhisper.net/uplfolders/upload2/mhz-mem-cbid.JPG

[gsan]

Corsair CMX256A-3500C2
XMS3502 v1.1
0315086
XMS3500 256MB 433mhz CL2
at 3.8v

http://upl.silentwhisper.net/uplfolders/upload2/mhz-mem-cbid.JPG

how far your bh5 can go with 3.26v? coz i also got 1 pair of 256mb cmx3500c2 rev1.1

[chefnr1]

how far your bh5 can go with 3.26v? coz i also got 1 pair of 256mb cmx3500c2 rev1.1
well at 3.26 i think i'll have got them to around 260+ its long ago that i've had that low volt on them :)

[gsan]

woww... 260+ but mine only can 243mhz :(
btw,

Winbond
23320
W942508BH-5

this bh5 is belong to which week?

[masterofpuppets]

Cool thread! I gotta post some results here at some point.

[chefnr1]

woww... 260+ but mine only can 243mhz :(
btw,

Winbond
23320
W942508BH-5

this bh5 is belong to which week?
ok strange? but my sticks is outstanding :)
week of mine i have no idea have'n take hs of :p:

[FriGidi]

Corsair CMX256A-3500C2
XMS3502 v1.1
0315086
XMS3500 256MB 433mhz CL2
at 3.8v

http://upl.silentwhisper.net/uplfolders/upload2/mhz-mem-cbid.JPG
Can you run example SP1M with those clocks?

Heres mine highest SP8M with KHX3500 at 3.7v 270Mhz (http://i148.exs.cx/img148/4200/27034mhz9aj.jpg)

[chefnr1]

Can you run example SP1M with those clocks?

Heres mine highest SP8M with KHX3500 at 3.7v 270Mhz (http://i148.exs.cx/img148/4200/27034mhz9aj.jpg)
no i can't do it now because i've not have the rigg it's sold, but i have run att 275x 11 and done 30 sec but the screen is in an other hdd, i've tryed to run super-pi on 286x11 but it said not equal somthing :) so on that speed it doesnt want it...

[Formann]

Winbond
314WE
W942508BH-5

280 1.5-2-2-5 @ 3.7v

http://privat.bluezone.no/forman/images/280.JPG

[saaya]

My A-DATA 3012E 256MB BH-5 260 2-2-2 at 3.5v superpi 32m pass &
memteat pass 6 loop.250 2-2-2-5 at 3.3v run prime95 2hour :D
what chip setting? :)

thx pershoot, added :)

With intel managed to drive 272Hhz fsb 1:1 with my pair of khx3000 sticks
http://valid.x86-secret.com/show_oc?id=7653
SuperPi 8m also went through

what chip setting or spd programming date?

Crimson_dAWN, nice! but please let me know what the max prime + 3d stable speed is! :D

chefnr1, chip date or spd programming week?
and 3d stable +prime95 blend results only please :)

woww... 260+ but mine only can 243mhz :(
btw,

Winbond
23320
W942508BH-5

this bh5 is belong to which week? hey, please post a reply with all your results ,and add what the max 3d plus prime95 blend speed is :)

Cool thread! I gotta post some results here at some point. :bows:

Formann, thx, but again, prime95 blend +3d stable speeds only please :)
superpi behcnable can hardly be called stable, and memtest seeems to run great sometimes but the mem wont even boot into windows at the same speed, so please use prime95 blend+3dmark or q3 or some other 3d bench to test stability, thx :)

[chefnr1]

Have to post when i get the new rig becuse this rig i've had that speed i sold so i will post some later when my new finaly arrive..

[saaya]

np, take your time :D

seems this thread will live at least 2x as long as i originally thougt since bh5 production has started again and we will have new bh5 in a few weeks :lol:

[TEDY]

so my twinmos speed premium 1A4T already qualifies again for this section ? :=)

[saaya]

sure :)
its relabeled bh5... :D

(or is it ch5?) ask alonso, he knows :)

[Evil_Spork]

new results...

nf4, 280mhz mem, bh5, khx3200, one 256 of 315WE, one 256 of 327WF. run in dual channel, 3.8v

also 275mhz bh5, khx3200, 339WF, dual channel, 3.6v

edit: both results run at 2-2-2-2

[SAE]

new results...

nf4, 280mhz mem, bh5, khx3200, one 256 of 315WE, one 256 of 327WF. run in dual channel, 3.8v

also 275mhz bh5, khx3200, 339WF, dual channel, 3.6v

edit: both results run at 2-2-2-2
Completely stable?! :D

I mean, can you do occt or s&m with it? I really do wonder as I never got stable results with memtest-stable ram...

[zt_lee]

anybody has kingston kvr bh 5 0251WE? i want to know how good is this chip, thks a lot

[Evil_Spork]

Completely stable?! :D

I mean, can you do occt or s&m with it? I really do wonder as I never got stable results with memtest-stable ram...
not stable at 280, 275 is pretty stable though. 270 is stable, and 265 is like theres no stress on the ram. :p:

280 is tested 3dmark stable. superpi wont run on this mobo at high clocks so that cant be used... but sandra and everest work as well as 3d01! :)

[SAE]

not stable at 280, 275 is pretty stable though. 270 is stable, and 265 is like theres no stress on the ram. :p:

280 is tested 3dmark stable. superpi wont run on this mobo at high clocks so that cant be used... but sandra and everest work as well as 3d01! :)
Yeah, bud, I know these superpi probs. Please give lowering LDT multiplier a try :)

I was able to complete superpi32m at 270x12 with my kingstons (3.5V). But I had to set LDT to 3x. (310p) And it's not memtest stable showing some errors at times.

Seems that mem does not like 3.6V+

[Evil_Spork]

Yeah, bud, I know these superpi probs. Please give lowering LDT multiplier a try :)

I was able to complete superpi32m at 270x12 with my kingstons (3.5V). But I had to set LDT to 3x. (310p) And it's not memtest stable showing some errors at times.

Seems that mem does not like 3.6V+
ill try 3.5v and LDT 3x.. but im pretty sure im using 3x already :(

[althes]

Just to add a little, using some buffalo bh5 and testing them now on DFI ultra-d.
Can get to 275 at 2.5/4/4/7

[SAE]

Just to add a little, using some buffalo bh5 and testing them now on DFI ultra-d.
Can get to 275 at 2.5/4/4/7


Why those slooooow timings, mate!? :D

@Evil_Spork

G'luck man :up:

[Teukka76]

What can I expect from old school BH5 that goes 230MHz 2-2-5-2-1 3.0V if I run those at 3.6V?

[SAE]

What can I expect from old school BH5 that goes 230MHz 2-2-5-2-1 3.0V if I run those at 3.6V?
One cannot really predict what it's gonna do. Some sticks don't even like 3.6V (my KHX3200 BH-5 for example)...

But they can bench 270 1.5-2-2-2 1T at 3.55V :D (Superpi32m)

[Teukka76]

Ok I got two set now to choose from:
1: 225MHz 2-2-2-5 DC 2.85V Twinmos ~2 years old DDR400
2: 230MHz 2-2-2-5 DC 3.0V Kingston Value DDR400

I think that I going for #1

[SAE]

Ok I got two set now to choose from:
1: 225MHz 2-2-2-5 DC 2.85V Twinmos ~2 years old DDR400
2: 230MHz 2-2-2-5 DC 3.0V Kingston Value DDR400

I think that I going for #1

It depends on what boards/cpus were used for shown results :)

The Twinmos may be burnt in a bit better as it's already 2 years old ;)
But the Kingston could end up with higher clocks too... maybe it responds better to higher voltages.

Do you already have them laying in front of ya, or do ya have to buy them prior to testing them? :D

[Teukka76]

Now I got the Twinmos BH5 set (http://kotiweb.kotiportti.fi/teemu.koistinen/kuvat/bh5.jpg).
Can't test it with higher voltages until I get my DFI.

According the database I should get these around 260MHz @3.3V

[SAE]

Good luck :up:

[Rub87]

Don't forget to burn them in well...

BURN!! :D

[hipro5]

UPDATE with the 2 x 256MB Kingston Value Rams of mine.......BH-6 PC2700(DDR333)........Running on a AMD system stock heatsink - low frequency(for the time been till I put it in my phase cahnge)......NOT bad for a start!...... :D

3D Benchable at 287MHz 1:1.....till now and climbing..... :D


http://www.thelab.gr/images/Hipro5/AMD/png/Cpu_Z_BH6_288MHz_png.png

[-dr-]

UPDATE with the 2 x 256MB Kingston Value Rams of mine.......BH-6 PC2700(DDR333)........Running on a AMD system stock heatsink - low frequency(for the time been till I put it in my phase cahnge)......NOT bad for a start!...... :D

3D Benchable at 287MHz 1:1.....till now and climbing..... :D


http://www.thelab.gr/images/Hipro5/AMD/png/Cpu_Z_BH6_288MHz_png.png*looking at my sanmax pc3200 bh-5 which can`t do 260+... sigh*

btw, how much Vdimm do you use to get that result?

[sobol]

Btw guys, there was in past some story about CH-5 and builded in voltage regulator... some buffalo tech guy said its reason why they start to clock so well with voltage above 3.2v ( after 3.1v it supposed to turn off). And now mostly peeps says its just the way chips are builded.....

[STEvil]

there never has been built in voltage regulators on DDR SDRAM.

[hipro5]

*looking at my sanmax pc3200 bh-5 which can`t do 260+... sigh*

btw, how much Vdimm do you use to get that result?

3.82Vdimm...... :)

[funkflix]

3.82Vdimm...... :)

Ur BH6 are really really nice! :toast:

Reached 280MHz with 3,9V with mine.

[ajshin27]

I have KHX3200k2/512. In aida32 one stick reads:

Module Name Kingston K
Serial Number 030495B6h
Manufacture Date Week 22 / 2003
Module Size 256 MB (1 rows, 4 banks)

and the other:

Memory Module Properties
Module Name Kingston K
Serial Number 0304C4B6h
Manufacture Date Week 22 / 2003

Can someone tell me if these are bh-5?

I'm running them at 2-2-2-11 at 200mhz with 2.82 vdimm. This is the highest I could get it prime95 stable with my athlon xp 1700 jiuhb dlt3c. Max stable memtest was at 210mhz with the same timings and volts.

[kasius]

Hi:

I have a pair of 512mb KHX3000 BH5. Week are 318WF.

I have tried with 2.96-2.98v of my NF7-s (no booster and MSI NEO2 is RMA) and it can research 230 2-2-2-11 memtest free errors. But my question is other, Is more better remove heat spreader running at high voltajes?? I would like to put 3.6-3.7v. Allways with a 120mm fan!!

Thanks

[playah]

Mushkin pc3200 222 special(BH6 I guess) ,just came in the mail "almost new" 245x10 3.3v 1:1 cpc on 2-2-2-11 memtest 6 passes no errors,246 5 passes 8 errors active cooling now burn in

[Lewis]

TwinMOS BH-5 2x256MB 'we310' does 225FSB, 2-2-2-11, DC, NF2 @ 2.9v (Abit NF7-Sv2)
Memtest86 stable

[Rub87]

I have KHX3200k2/512. In aida32 one stick reads:

Module Name Kingston K
Serial Number 030495B6h
Manufacture Date Week 22 / 2003
Module Size 256 MB (1 rows, 4 banks)

and the other:

Memory Module Properties
Module Name Kingston K
Serial Number 0304C4B6h
Manufacture Date Week 22 / 2003

Can someone tell me if these are bh-5?

I'm running them at 2-2-2-11 at 200mhz with 2.82 vdimm. This is the highest I could get it prime95 stable with my athlon xp 1700 jiuhb dlt3c. Max stable memtest was at 210mhz with the same timings and volts.

I have the same and mine are BH-5, but I think it's better you remove the heatspreaders, they really suck on singlesided kingston sticks...

[ajshin27]

I have the same and mine are BH-5, but I think it's better you remove the heatspreaders, they really suck on singlesided kingston sticks...

As in, they hinder the performance of the ram? And if so, by a lot? If it's only by a little, I'd rather not chance ruining the sticks. Yeah, i know, i'm chicken, but oh well.

[Rub87]

No, but they work more like an isulater then as a heatspreader..

If you remove the clips with a small screwdrive the side where the chips are comes of easy.. the chipless side I didn't remove..

[Xevipiu]

Helloooo

My 2x256 OCZ3500 Platinium Limite Edition (PLE) Winbond BH5 338WF

http://img199.exs.cx/img199/2581/262x16xevipiuciusbert9wd.th.jpg (http://img199.exs.cx/my.php?loc=img199&image=262x16xevipiuciusbert9wd.jpg)
Abit IC7 Max3 (Bios 18), 3.2E@4.191mhz (262x16) 1:1 2-2-2-5 1T 3.43v @875
52º full Watercooled

Bye

[saaya]

new results...

nf4, 280mhz mem, bh5, khx3200, one 256 of 315WE, one 256 of 327WF. run in dual channel, 3.8v

also 275mhz bh5, khx3200, 339WF, dual channel, 3.6v

edit: both results run at 2-2-2-2

stable? :D
remember, im looking for prime95 blend+3dmark stable results
so whats the max speed? 270?

Just to add a little, using some buffalo bh5 and testing them now on DFI ultra-d.
Can get to 275 at 2.5/4/4/7
are you sure its bh5? ^^
what voltage?

hipro, what board? and whats the max prime95+3d stable?
amazing results! makes me wanna go out and hunt for 2700 bh5 on ebay again :lol:

Ur BH6 are really really nice! :toast:

Reached 280MHz with 3,9V with mine.did you post the stepping already? if not please post the stepping and board and im going to add it :D
3d+prime95 stable?

ajshin27, what board was that on?

kasius, whats the max stable prime95+3d speed?
and i would remove the heatspreaders... but if you dont know how to do it and care about warranty then better dont...

playah, whats the max speed with prime95+3d? and what board was this on?
if its new special 2-2-2 its tccd

Lewis, whats the max 3d+prime95 stable speed?

Xevipiu, whats the max 3d+prime95 speed?

[funkflix]

1M + Hexus Pifast stable .... :D

http://weber-steuerungstechnik.de/felix/bh6pic2.gif

DFI nF4

[althes]

stable? :D
remember, im looking for prime95 blend+3dmark stable results
so whats the max speed? 270?


are you sure its bh5? ^^
what voltage?
Yes it is using 3.8v, these were some of first sticks made
hipro, what board? and whats the max prime95+3d stable?
amazing results! makes me wanna go out and hunt for 2700 bh5 on ebay again :lol:

did you post the stepping already? if not please post the stepping and board and im going to add it :D
3d+prime95 stable?

ajshin27, what board was that on?

kasius, whats the max stable prime95+3d speed?
and i would remove the heatspreaders... but if you dont know how to do it and care about warranty then better dont...

playah, whats the max speed with prime95+3d? and what board was this on?
if its new special 2-2-2 its tccd

Lewis, whats the max 3d+prime95 stable speed?

Xevipiu, whats the max 3d+prime95 speed?


Yes it is using 3.8v, these were some of first sticks made

[Evil_Spork]

stable? :D
remember, im looking for prime95 blend+3dmark stable results
so whats the max speed? 270?


both sets work pretty much exactly the same. the unmatched pair will run 3d at about 3fps higher.

265 with 3.6v is rock stable
275 with 3.8 should be too.. i dont have prime, or a computer to test right now, as you know exhbach and i just murdered our A64 rigs. :rolleyes:

[babyelf]

can't get aida no more.. any ideas on how to get the week with other programs? cpuz spd is empty .. can't find it in everest too..

but doing 260mhz 2-2-2-5 3.3V prime/memtest/games stable.. gonna push it up higher

http://img.photobucket.com/albums/v394/babyelf/260tight32mb.jpg
http://img.photobucket.com/albums/v394/babyelf/memtest260.jpg
http://img.photobucket.com/albums/v394/babyelf/pi.jpg

[Rub87]

can't get aida no more.. any ideas on how to get the week with other programs? cpuz spd is empty .. can't find it in everest too..

but doing 260mhz 2-2-2-5 3.3V prime/memtest/games stable.. gonna push it up higher

http://img.photobucket.com/albums/v394/babyelf/260tight32mb.jpg
http://img.photobucket.com/albums/v394/babyelf/memtest260.jpg
http://img.photobucket.com/albums/v394/babyelf/pi.jpg

Taking the heatspreaders off isn't an option?

[gsan]

babyelf,

ur bh5 damn good! which brand of this ram and what about the week production?

[babyelf]

i can't get the production week.. duno y.. not in cpuz and everest and i can't get aida32 anymore..

but here's some results after i bumped it up to 3.4v .. 3.3v is probably almost hitting the limit at 260mhz 2-2-2-5

4 errors at the 4 or 5th loop can't remember then clean test after that.. gonna run some 32mb later

http://img.photobucket.com/albums/v394/babyelf/DSCN2350.jpg

[playah]

playah, whats the max speed with prime95+3d? and what board was this on?
if its new special 2-2-2 its tccd



It's the Mushkin PC3200 2-2-2 special(BH6),I've got the Mushkin Lvl2 V2 TCCD and it ain't them.Afraid I might have pumped a little too many V's in 'em.
DFI LP u b,Vmodded 3.6v w/Hellfire 3EG REV2 bios,was tryin to push to 10x250 w/cpc off 2,2,2,11.Pasted memtest fine,then tried to prime,no go,went back to memtest..lots of errors.Sorry just got disgusted and took 'em out.

I've got new xp-m2600 ADYHA 0503 was just see'in what'd do,I'll retest later and report back.

[Xevipiu]

Hello. that result are the normal ones of a few KHX3500 314we??? :(

To I never dress 244 2-2-2-11 in only 2.9v mounting in a NF7-S :rolleyes:

Byeeee

[wwwww]

my bh5 doesnt give details in cpuz, everest or aida.

ive taken of the ihs

it says

Winbond
335WF
W942508BH-5

What week and stuff is it?

[TEDY]

35 week 2003

[wwwww]

Alright I got a pair of 512MB mushies;

they do DDR500 @ 3.2V on nf3]

they are week 35 2003

[saaya]

hey, thank you very much everybody for posting more and more results, its really appreciated! :toast: im glad to see im not the only one obessed with bh5 :D

but im relly busy atm, can you do me a favour and post your results in the right sheme so i dont have to pick up all the details myself? :(

please post all results following this sheme? thx :)

"2302D" 2.0-2-2 3.25v 235mhz (adata 3200 256mb@nf2)

[wwwww]

"335WF" 2.0-2-2 3.2v 250mhz (Mushkin 3500 lvl2 512mb@nf3)
"335WF" 2.0-2-2 3.2v 250mhz (Mushkin 3500 lvl2 512mb@nf3)

[saaya]

thx man! :toast:

[SoF]

well even it was hot yesterday i took another benchie run first time trying 1:1 with 3.6V
here is the result:

http://www.casextreme.net/pixx/benches/258ramcpuzs.jpg

:toast:

[Mardok]

http://members.lycos.co.uk/m4rd0k/xs/PI32_25-33_mini.jpg

338we 284MHz @ 3,66v

[13oost]

Taking the heatspreaders off isn't an option?

babyelf,

ur bh5 damn good! which brand of this ram and what about the week production?


its OCZ Value Ram series

the Ram has been rebranded and all info flushed, plus no heat spreaders

from what weve been told by OCZ is that its the same BH-5 Modules from the new Gold series

Edit:: im running, 2x512mb 230mhz 2-2-2-5 @ 2.96vdimm, memtest stable
running OCZ Value Ram, no clue on week info, no programs will tell me, and can find any info on the die numbers

running on an NF7-S, 230x11 2 1.85vcore

http://valid.x86-secret.com/show_oc.php?id=20500

[El Snorro]

"303WF" 2.0-2-2-5 3.5v 265mhz (twinmos 3200 256mb@nf3)

[arcane613]

saaya, quick question.. i noticed something before i pulled the heatspreaders off...
you said to put something similar to the following ("2302D" 2.0-2-2 3.25v 235mhz (adata 3200 256mb@nf2)).. and i do see some numbers like that in the database... if i look on my mushkin special BH-6, it has the reg stepping... but there is a little IC at the bottom, visible with the heatspreader on... is 2402E, could mean some peeps r reading that instead of taking the full IHS off? jus wondering...

here is my Mushkin BH-6
"334WF" 2.0-2-2 3.2v 243mhz (mushkin 3200 512mb@nf2)

[CanDostum]

week 17,
year 2003,kingston hyperx 3500

http://img297.echo.cx/img297/2885/282fsbspi5jp.jpg

[felinusz]

I have two more for you saaya :)

First set is my 2x256 Megs Corsair XMS PC3500 v1.1. One stick has 310we stepped chips, the other stick is half and half 310we, and 322wf.

In my DFI nForce4 motherboard, this set peaks at 273 MHz for memtest86 stability, using 1.5-2-2-3 timings, and 3.78V of VDIMM voltage. BIOS revision 510-2.


Second result is my 2x256 Megs Mushkin Black LII PC3200. All the chips are stepped 3052e. The sticks peak at 270 MHz for memtest86 stability, using 2-2-2-5 timings, and 3.89V of VDIMM. BIOS Revision 510-2.

[culmen]

Kingstone value Pc2700
263@3,3v 40 week 02year
At 3,6v 280Mhz
Infineon remark same but i dont know
year and week.
In dual mode they are doing the same
In memtest86 (test 5) 264@3,3
All on dfi infinity nf2

[piotres]

Kingstone value Pc2700
263@3,3v 40 week 02year
At 3,6v 280Mhz
Infineon remark same but i dont know
year and week.
In dual mode they are doing the same
In memtest86 (test 5) 264@3,3
All at dfi infinity nf2

Ohh yeaahh - this dual will be mine for some weeks :rehab:

Culmen sells me this sticks :banana3: .

Probably it's the best BH-6 dual in Poland and there are also only one BH-5 kit which can go higher (Mardok's :p: ) .

It's Kingston DW-60 and Infineon AT-6 - both PC2700 value rams ... :hrhr: .

Culmen's friend clocked this DW-60 stick to 281/3.6 V on DFI NF3 .. :up: .


My currently sticks scores :

HyperX PC3200K2 2x256 MB single-sided

Everest detects them as a 37 week of 2003 . I did't remove the heatspeaders so I don't know :hm: :

270/5-2-2-2/3.71 V
266/5-2-2-2/3.63 V
260/5-2-2-2/3.41 V

all on DFI Ultra-D NF4

Edit : New owner of this KHXes has taken off the heatspeaders, and now we know that this is 336WF orginal BH-5 :cool: (both sticks) .


Best Regards
Peter

[Rub87]

Offtopic, but I smoked my NF7-s (for some reason a shotcut on the mobo's 12µv rail..) and ordered myself an DFI nf4 Ultra-D, as this is my first A64, what's the highest, safe level to put through a venicevdimm controller..?

[piotres]

Offtopic, but I smoked my NF7-s (for some reason a shotcut on the mobo's 12µv rail..) and ordered myself an DFI nf4 Ultra-D, as this is my first A64, what's the highest, safe level to put through a venicevdimm controller..?

Sorry but I continue a little this Off/T and I answer Rub :
On DFI NF4 you can easy go even to 4V vdimm (real can be even 4.06V) without any mods, you only can put a fan to Vdimm section- that's the only "mod" you need ;) .

Now On Topic back :) :

I remember that I also had 2 sticks of HyperX PC2700 256MB, some month ago - both remarked BH-5 to "0309 Kingston DW-50", twin sided :( .
One stick did 255 Mhz/3.53 V on DFI Lan Party Nf3, and second did 250 Mhz/3.3 V on DFI Infinity Nf2 :p: .

Best Regards
Peter

[KoNiaK]

Did twinmos release some 256MB sticks of BH5 in there pro line? or did all of their chips of BH5 went into the 3200 cas2.5 with out selections ?

[celemine1Gig]

Well, if I'm not mistaking, there are 256MB Twinmos Speed Premium modules, so perhaps, they are Winbond based (1A4T or AA4T).
Just saw that for example the Newegg product picture for the 256MB TMSP shows Winbond based chips. The question is only, if the pics match the real product that you'd receive.

BTW, in about 6 weeks (unfortunately no time ATM), I hope I'll be able to add the following to this database:
3x 256MB Infineon 6-A PC2700 (Winbond based, seems to be BH-6): 250 Mhz/3.2V
2x 256MB VT/Kreton PC3200 UTT chips (CH-die): 250MHz/3.2V
2x 512MB VT/Kreton PC3200 UTT chips (BH-die): 250Mhz/~3.4V
1x 512MB Infineon 6-A PC2700 (same as the 256MB Infineons): 200MHz/2.8V
1x 512MB FCM PC2700 Winbond BH-6: not here yet
Fastest timings (2-2-2-10 for all sticks).

I know, none of the modules is BH-5-based, but I still hope that the results will be accepted, when I finally post them. :)

Exact results from all the modules will follow. :)

[KoNiaK]

Did twinmos release some 256MB sticks of BH5 in there pro line? or did all of their chips of BH5 went into the 3200 cas2.5 with out selections ?

Thanks celemine1Gig but I am wondering about the old BH5 not the UTT

[celemine1Gig]

Thanks celemine1Gig but I am wondering about the old BH5 not the UTT

Well, I don't really get what you mean then. :confused:
Old BH-5 isn't available anymore for over a year. How come, you think that Twinmos should be able to produce with old chips?
The only chance to get old BH-5 equipped 256MB sticks is eBay or forums. I doubt that there is any reseller that still has stock on the old modules.

And if you mean the old "new" BH-5 (UTT is synonymous for new CH-die and BH-die chips, in case you don't know), just look for "1A4T". Otherwise, no chance to still get old BH-5 sticks. At least you won't find any recent Winbond chips with a real Winbond label printed on them. All chips available ATM are remarked.

[KoNiaK]

I got a friend who have some old BH5 from twinmos - not new die CH or BH. It´s regular 3200 twinmos, SPD 2.5, but not twister/pro line. That´s why I wonder if they are gona be any good or if it´s only the crapy chips which went in this line and the good one in another.

I didn´t find any informations telling me that twinmos produced BH5 in twister or pro line, but it´s probably a 2 to 3 year old if it existed so it would not be surprising if can´t find the information even if it existed.

The problem is that where I live now it´s gonna be a real pain to send them and recieved them in a good shape. I´ll also have to gather informations about the customs. I don´t want to go threw all this crap if it´s sure that the stick won´t clock high.

[celemine1Gig]

Man, honestly, use the search function next time. I don't know how much threads there are about the original old Twinmos BH-5 sticks, but there sure are plenty.

99% of the time, there was no difference between Twinmos and let's say Mushkin or any other BH-5 RAM.
It's just luck of the draw. Either you get a good, a average or a bad pair. Doesn't matter if it says Twinmos or something else on the sticks.

[KoNiaK]

And how I look for a model that I don´t know if it exist and even don´t know the potential name ;)

I´d actualy did a few search with twister+bh5 and cheked the ram list, before posting, nothing. But the list is not exaustive for twinmos. What I am actualy looking forward is that the rep tell me if there was or not.

In this case it´s not "let's say Mushkin or any other BH-5" it´s more like VX 3500 vs 4000 ;)

[gsan]

corsair 2x256mb pc3500 bh5 on nf7-s

250 @ 2-2-2-11 , 3.6v (WE302 & 326)

http://img.photobucket.com/albums/v235/gsan_bot/PICT0088.jpg

[KoNiaK]

Is there a screen for:
"314we" 2.0-2-2 3.90v 290mhz (khx 3500 256mb@nf3)

Can´t find it with search tool, is it single?

[Rub87]

corsair 2x256mb pc3500 bh5 on nf7-s

250 @ 2-2-2-11 , 3.6v (unknown week and year)

http://img.photobucket.com/albums/v235/gsan_bot/PICT0088.jpg


What mods are you running? How much chipset voltage, I can also run 250 mhz single channel but dual channel totally sucks..

[gsan]

What mods are you running? How much chipset voltage, I can also run 250 mhz single channel but dual channel totally sucks..

memtest#86 test 5, chipset 1.7vdd, I'm going to mod the ddr booster soon, see whether can give me extra mhz or not. :)

[rzonealley]

didnt see any twinmos pc3500 result yet. mostly pc3200.

[Giana]

I didnt read all the 24 Pages full of postings ;) Just took a look at the List on the first Page. And there is something that really makes me confused.

"3092E" 2.0-2-2 3.30v 245mhz (twinmos 3200 256MB@nf2)

Should be BH5 ...

BUT !

I have Sticks with exactly!! this "3092E" on the Chips and they are labeld as BH6 ! And were sold as DDR333. They also do this 245 Mhz @ 3.3v ....

:confused:

[celemine1Gig]

I didnt read all the 24 Pages full of postings ;) Just took a look at the List on the first Page. And there is something that really makes me confused.

"3092E" 2.0-2-2 3.30v 245mhz (twinmos 3200 256MB@nf2)

Should be BH5 ...

BUT !

I have Sticks with exactly!! this "3092E" on the Chips and they are labeld as BH6 ! And were sold as DDR333. They also do this 245 Mhz @ 3.3v ....

:confused:

Man that is only the production year and week and an additional internal code from winbond. This has absolutely nothing to do with the labling of the chips as BH-5 or BH-6. ;)

[boblemagnifique]

2*256 adata 0313we -> 275.4mhz 2/2/2/5/7/12/2/2/1/2 at 3.8v bios

http://www.membres.lycos.fr/boblemagnifique/divers/313we.jpg

http://www.membres.lycos.fr/boblemagnifique/divers/bh5batch.jpg

the 2 first make 275mhz stable
the 2 others soon in test :)

stable Superpi 32mo / 3d mark (no test memtest)

http://www.membres.lycos.fr/boblemagnifique/Overclocking/A64/lbble0520apmw/superpi32mo.JPG

[krampak]

There is no week 36? Here comes mine:

"336wf" 1.5-2-2 3.65v 265mhz (http://img341.imageshack.us/img341/9203/venice3od.jpg) (Mushkin PC3500 512mb@nf4)

[gsan]

@ boblemagnifique

nice bh5 u got :)

[boblemagnifique]

thank

batch 0309 & 0346 :D (vddr 4v , bios 309 or 702-2)

http://www.membres.lycos.fr/boblemagnifique/Overclocking/Bh5/278.1mhz.jpg

[Perc]

hey guys

ive got some corsair Plat(XMS3205v1.1) i bought like 1 1/2 yrs ago off of someone in this forum. they are bh-5 the chips are labeled whinbond 3072E W942508BH-5 i last used these way back in my NF2-2600xp-m system and i believe 250fsb was what i was getting 2-2-2 but if you rember back then 250 on a nf2 was damm good and mostly rare so im sure if i tried these in my 64 system id probly see alot nicer results no?

ill pop these babys into my 64 rig and test em out. ill post back with results..

peace perc,

[Rub87]

Hi, my BH-5 does around 265-270 on lanparty..

Is ist normal that if I run the mem for exempla @ the 7:10 divider it is able to archive better results then when running 1:1 with the same timings?

[saaya]

can't get aida no more.. any ideas on how to get the week with other programs? cpuz spd is empty .. can't find it in everest too..

but doing 260mhz 2-2-2-5 3.3V prime/memtest/games stable.. gonna push it up higher

everest also shows the spd week irc :)

saaya, quick question.. i noticed something before i pulled the heatspreaders off...
you said to put something similar to the following ("2302D" 2.0-2-2 3.25v 235mhz (adata 3200 256mb@nf2)).. and i do see some numbers like that in the database... if i look on my mushkin special BH-6, it has the reg stepping... but there is a little IC at the bottom, visible with the heatspreader on... is 2402E, could mean some peeps r reading that instead of taking the full IHS off? jus wondering...

here is my Mushkin BH-6
"334WF" 2.0-2-2 3.2v 243mhz (mushkin 3200 512mb@nf2)LOL, never thougt of that... but id be surprised if they read the stepping of the spd eeprom chip, there are at least 2 guys i go theese codes from who i dont think are stupid enough to not know what the eeprom and what the winbond chip is :D
so i think its just a coincidence...

I have two more for you saaya :)

First set is my 2x256 Megs Corsair XMS PC3500 v1.1. One stick has 310we stepped chips, the other stick is half and half 310we, and 322wf.

In my DFI nForce4 motherboard, this set peaks at 273 MHz for memtest86 stability, using 1.5-2-2-3 timings, and 3.78V of VDIMM voltage. BIOS revision 510-2.


Second result is my 2x256 Megs Mushkin Black LII PC3200. All the chips are stepped 3052e. The sticks peak at 270 MHz for memtest86 stability, using 2-2-2-5 timings, and 3.89V of VDIMM. BIOS Revision 510-2.
thx, added your info as this: (memtest isnt windows+3d stable so i entered a slightly lower result)
"310WE" 2.0-2-2-5 3.8v 270mhz (corsair 3500 256mb@nf4)
"310WE" 2.0-2-2-5 3.8v 270mhz (twinmos 3200 256mb@nf4)
"322WF" 2.0-2-2-5 3.8v 270mhz (twinmos 3200 256mb@nf4)

"3052E" 2.0-2-2-5 3.9v 265mhz (mushkin 3200 256mb@nf4)
"3052E" 2.0-2-2-5 3.9v 265mhz (mushkin 3200 256mb@nf4)

Did twinmos release some 256MB sticks of BH5 in there pro line? or did all of their chips of BH5 went into the 3200 cas2.5 with out selections ?they aölso made a very limited eidtion of pc3700 with bh5 chips :D
a veeery rare edition, i own a dual channel kit of those, havent seen anybody else with twinmos 3700 based on bh5 so far.

so to answer your question, back then 99% of the bh5 went to the vanilla 3200 2.5-3-3 sticks. twinmos now has a high performence offer for memory, back then they only had value stuff afaik.

Is there a screen for:
"314we" 2.0-2-2 3.90v 290mhz (khx 3500 256mb@nf3)

Can´t find it with search tool, is it single?
most likely single, yeah, and not everybody here sent me screenshots, i trust people if they say they reached a certain speed :)

I didnt read all the 24 Pages full of postings ;) Just took a look at the List on the first Page. And there is something that really makes me confused.

"3092E" 2.0-2-2 3.30v 245mhz (twinmos 3200 256MB@nf2)

Should be BH5 ...

BUT !

I have Sticks with exactly!! this "3092E" on the Chips and they are labeld as BH6 ! And were sold as DDR333. They also do this 245 Mhz @ 3.3v ....

:confused:i know, i think winbond labeled some as bh5 and some as bh6 but they are actually made in the old 150nm process (bh6)

hey guys

ive got some corsair Plat(XMS3205v1.1) i bought like 1 1/2 yrs ago off of someone in this forum. they are bh-5 the chips are labeled whinbond 3072E W942508BH-5 i last used these way back in my NF2-2600xp-m system and i believe 250fsb was what i was getting 2-2-2 but if you rember back then 250 on a nf2 was damm good and mostly rare so im sure if i tried these in my 64 system id probly see alot nicer results no?

ill pop these babys into my 64 rig and test em out. ill post back with results..

peace perc,
yepp :D
be sure to post the results hehe :D

Hi, my BH-5 does around 265-270 on lanparty..

Is ist normal that if I run the mem for exempla @ the 7:10 divider it is able to archive better results then when running 1:1 with the same timings?
you mean the memory is running slower than the fsb and this gives you a higher oc? hmmm i never heard of this before.
if it was the other way around it could be that your fsb is limiting you.

you do know that a divider slightly changes your memory speed, right?
so it will show your memory speed as a few mhz higher than it actually is, while in 1:1 it always shows the exact memory speed in cpuz for example.

@everybody:
thx a lot for all those new entries! :D
unfortunately half of you posted the results not like i asked you to and there are infos missing so i cant add them :P
i sent those people a pm asking them to pm or post the full results, and to please post them as:

"303WF" 2.0-2-2-5 3.5v 265mhz (twinmos 3200 256mb@nf3)

for example :D

thx a lot again to all the people who are sharing their reults here :toast:

[largon]

i know, i think winbond labeled some as bh5 and some as bh6 but they are actually made in the old 150nm process (bh6)
:nono: Winbond's datasheets actually prove BH-6 is 175nm. Just like BH-5.

btw. I updated your "the bh-5/bh-6 legend (http://xtremesystems.org/forums/showthread.php?p=1038005#post1038005)" thread.

[saaya]

nice research!
why didnt you pm me about this earlier? didnt notice your posts :D

[eliminate]

what about the OCZ Gold Series Winbond UTT BH5?

[saaya]

thats what i also wondered about. there is def new bh5, but is it really bh5 or is it ch5 tested to run 2-2-2 and then labeled bh5 by winbond even though its actually a different ic? there is definately ch5 that runs 2-2-2, so why would winbond go back to an older design and produce bh5 ics? hmmm

[SoF]

I sended sayaa these results via pm yesterday, but there aren't complete, I told him already...this is what I had on BH5 this year (5 of these pairs were belonging to a friend of mine):

System: MSI K8N Neo2 Platinum + 3000+ Winchester
ALL 2x512MB Dual Channel
ALL Timings: 2-2-2-5-12 1T
ALL Memtest86 5&7 30min

TT Twinmos BH5 (no more details sry)
240MHZ 3.08V
260MHZ 3.31V
270MHZ nicht möglich

TT Twinmos Black (black HS, no more details sry)
240MHZ 3.05V
260MHZ 3.65V
270MHZ 3.9V

Twinmos Relabled BH5 (no more details sry)
240MMHZ 3.15V

Twinmos 311WE W942508BH-5
270MHZ 3.84V

Twinmos Relabled 03034TMD7608F8E50D
240 MHZ 3.37V
245MZH 3.47V

K8N Neo2 Plat. + 3500+ NC
2x512 MB Kingston KHX BH5 (maybe I'll find the detailed description)
258MHZ 3.6V

2x512 MB NEW BH5 Twinmos
~ 245MHZ @3.6V but just for testing purposal

Again sorry I missed to write down all the details of the BH5 but at least you can see a few new results ;)

Regards,
SoF

[FriGidi]

2*512 Kingston Value PC3200 BH5 "251we"

Anybody got ScreenShot from A64 tweaker settings to try? :)

[funkflix]

U can try this :

http://img104.imageshack.us/img104/7088/timings6lj.jpg

Great Bandwith, Stability and Performane, but not all sticks will do that.

[FriGidi]

Pushing Set freeze the system. Sticks doesn`t like that Max Async Latency 9ns.

[funkflix]

And with an other Max Async Latency it works? Can't set it below 9, or i get instant freeze, after Bios-screen. With my Neo2 it works with 6.0/4.0 ...

[FriGidi]

Yes, Max Async Latency 6ns-8ns works great. Now I´m testing with your settings example Max Async Latency is 6ns :)

Oh and mobo is Gigabyte K8NSU NF3.

[funkflix]

K fine, good luck! :)

[Xevipiu]

Hola Saaya. (Lo prometido es deuda :) )

2x256 KHX3200 339wf
http://img84.imageshack.us/img84/232/epsn05759kw.th.jpg (http://img84.imageshack.us/my.php?image=epsn05759kw.jpg)

1mb Spi1mb:
265mhz 2-2-2-0 1T 3.23v
http://img84.imageshack.us/img84/4691/32v2651mb0jd.th.jpg (http://img84.imageshack.us/my.php?image=32v2651mb0jd.jpg)

277mhz 2-2-2-0 1T 3.55v
http://img304.imageshack.us/img304/9233/355v2771mb0hx.th.jpg (http://img304.imageshack.us/my.php?image=355v2771mb0hx.jpg)

282mhz 2-2-2-0 1T 3.66v
http://img304.imageshack.us/img304/7255/366v2821mb9jb.th.jpg (http://img304.imageshack.us/my.php?image=366v2821mb9jb.jpg)

285mhz 2-2-2-0 1T 3.82v
http://img304.imageshack.us/img304/3504/382v2851mb6ey.th.jpg (http://img304.imageshack.us/my.php?image=382v2851mb6ey.jpg)
Maxim stable 3.93v

Spi8mb:
280mhz 2-2-2-0 1T 3.71v
http://img304.imageshack.us/img304/9182/371v2808mbtimmings0om.th.jpg (http://img304.imageshack.us/my.php?image=371v2808mbtimmings0om.jpg)
+ In process

Spi32mb:
In process...

Bye

[felinusz]

Wow, nice 8M results!

[kasius]

Hi:

I purchased on Ebay 2x512 Corsair LLPT. This guy don´t know he was selling BH5 ^^. He tell me he did not OC never.

I remove heatspreader and this is:

307WE the two sticks

And I hit with 3.31v in memtest86 this:

- Module 1; 256 2-2-2-5
- Module 2; 260 2-2-2-5

But, when I put the two memory stick with the same voltaje (3.31) it only do 248 2-2-2-5
It´s posible???? :confused:

I´m with a MSI NEO2, with Vdimm@3.3v mod and a powerstream PSU. 3.31v with tester when memtest is runing.
Bios 1.8MOD.


Thanks

[chikitano]

Hello

My corsair 3500c2 v1.1 2x256 (2452D)

http://img526.imageshack.us/img526/1024/bhd37s1m9rk.th.jpg (http://img526.imageshack.us/my.php?image=bhd37s1m9rk.jpg)

Salu2

[5days]

Hello

My corsair 3500c2 v1.1 2x256 (2452D)

http://img526.imageshack.us/img526/1024/bhd37s1m9rk.th.jpg (http://img526.imageshack.us/my.php?image=bhd37s1m9rk.jpg)

Salu2
Nice time and checksum. ;)

[chikitano]

Hello

There is no space for everything ;) I will post other pic after burning (with time and checksum)

Salu2

[Xevipiu]

Hello

My corsair 3500c2 v1.1 2x256 (2452D)

http://img526.imageshack.us/img526/1024/bhd37s1m9rk.th.jpg (http://img526.imageshack.us/my.php?image=bhd37s1m9rk.jpg)

Salu2

mm nice memos:)

OT: Todas llevan la misma semana? Seguro q no

Salu2

[chikitano]

Hello

Hi:

I purchased on Ebay 2x512 Corsair LLPT. This guy don´t know he was selling BH5 ^^. He tell me he did not OC never.

I remove heatspreader and this is:

307WE the two sticks

And I hit with 3.31v in memtest86 this:

- Module 1; 256 2-2-2-5
- Module 2; 260 2-2-2-5

But, when I put the two memory stick with the same voltaje (3.31) it only do 248 2-2-2-5
It´s posible????

I´m with a MSI NEO2, with Vdimm@3.3v mod and a powerstream PSU. 3.31v with tester when memtest is runing.
Bios 1.8MOD.


Thanks

That also happens to me

V Stick1 Stick2 Dual

2.8 226 220 216
3.0 241 234 231
3.2 262 250 247
3.4 270 259 259

with the voltage it is solved

mm nice memos

OT: Todas llevan la misma semana? Seguro q no

Salu2

:D no, they are not the same week, of 4 faces, 3 are 245 and one is 246

PD: tengo unas mas chulas que estas...

Salu2

[Fixxxer]

I expect seeing soon the nice ones, Chikitano ;)

[Dani]

DFI nF4 SLI-D, 3.73VDIMM, AIR cooled CPU&MEM -1'C :cool:

CORSAIR CMX256A-3500 C2
XMS3502v1.1
024704

Stick1:
Winbond
2452D
W942508BH-5

and same stepping on other side

Stick2:
Winbond
2452D
W942508BH-5

and the other side

Winbond
2462D
W942508BH-5


http://koti.mbnet.fi/dani69/DFI%20nForce4%20Ultra-D/Opteron%20146/146_0540FPBW_SP8M_3360MHz_4m32s_1.64V_AIR.gif

http://koti.mbnet.fi/dani69/DFI%20nForce4%20Ultra-D/Opteron%20146/146_0540FPBW_SP32M_3315MHz_22m06s_1.7V_AIR.gif

[chikitano]

Hello

CORSAIR CMX256A-3500 C2
XMS3502v1.1
024704

Stick1:
Winbond
2452D
W942508BH-5

and same stepping on other side

Stick2:
Winbond
2452D
W942508BH-5

and the other side

Winbond
2462D
W942508BH-5

Very good result Dani, they are equal that my, but yours they are quite better, although cold also help :D ...whereupon voltage you have obtained it?

I expect seeing soon the nice ones, Chikitano

I also ;) .. because I am having more problems of the account :(

Salu2

[Xevipiu]

Chiki.

.- (331we) 2-2-2-0 1T 3.63v 270mhz (http://img463.imageshack.us/img463/9992/1mb27036alphaapretats3as.jpg) (Corsair3500C2 1.1v 256@nF4) Xevipiu

http://img463.imageshack.us/img463/9992/1mb27036alphaapretats3as.th.jpg (http://img463.imageshack.us/my.php?image=1mb27036alphaapretats3as.jpg)

Stick1: 250/250we

Stick2: 331/332we

P.D: Ahora te miro de que semana era el otro juego de C2, ese hacia 283 2-2-2-0 3.82v, creo q eran 250we todos son caras

Salu2

[Dani]

Hello



Very good result Dani, they are equal that my, but yours they are quite better, although cold also help :D ...whereupon voltage you have obtained it?

Salu2
Thanks M8 :)
Yes, 3.73V, I edited my post above;)

[Wayway]

sayaa i have mushkin lvl 2 3500 bh-5 2 x 256

one is 313we and other is 338wf right now super pi 1m and 32m and all game stable and all benchmark stable and memtest stable

right now there at 250 fsb 2-2-2-5 @ 3.4v dual channel

[pasatoiutd]

2*512 MB Corsair PC3500 C2PT v1.1 BH-5 + DFI Lanparty nForce 4 SLI-DR
vDimm = 3.6V (set in BIOS)
Cooled by a 120mm Antec fan

DDR 545 2-2-2-7

[TaPaKaH]

2x512MB Kingston HyperX KHX3200AK2/1G (Winbond CH-5)
Week 51 Year 05
3.0V - 224.3 MHz 2-2-2-5 Dual Channel
3.0V - 265.4 MHz 2.5-3-3-8 Dual Channel

[Mean Machine]

BH-5:
342WF - 261MHz 2-0-0-5 Dual Channel, 3.7V
Screen: http://files.upl.silentwhisper.net/upload4/26.454s.JPG (Does do as much as 270MHz, but I don't have any screenshot)

342WF - 280MHz 2-2-2-5 Single (One stick), 3.8V
Screenie: http://files.upl.silentwhisper.net/upload0/280.JPG (I eventually had enough after about three hours of memtest, so I simply shut it down. Rock solid, even though it was done on an Asrock-mobo)

[Godmaster]

week 22
"322wf" 2.0-2-2 3.4v 265mhz (xms 3500 2x256@nf2)
Original alpha timings
DDR DUAL CHANNEL ENABLED.

Nf7 rev 2.0 & xp-m

week 22
"322wf" 2.0-2-2 3.71v 260mhz (xms 3500 2x256@nf2)
2-2-2-2
alpha 0 0 3 3 3 0 3

[Bob21]

Corsair 3200LL 303WE 264MHz @ 3.5v 277@3.85v Neo2 nForce3

I'm sure it would do higher with nf4

[Hystrix^]

2*512mb GEIL Ultra-X 250Mhz @ 3.4V 265MHz @ 3.6 =>BH5 chips

tested on my Ultra-D

[krullet]

a-data old-bh5, 2*512..272mhz@2-2-2-5, 3.7V superpi stable

tested on ultra-d, sli-d and expert

[chikitano]

Hello

2x256 corsair 3200C2PT bh-6 338wf

http://img102.imageshack.us/img102/2595/bh6s2720ju.th.jpg (http://img102.imageshack.us/my.php?image=bh6s2720ju.jpg)

2x256 corsair 3500C2 v1.1 bh-5 2452E

http://img55.imageshack.us/img55/6865/275s1a388um.th.jpg (http://img55.imageshack.us/my.php?image=275s1a388um.jpg)

Salu2

[joek71]

Hi guys
I have this mem:
2Gb Kit Team Xtreem Cronus 3-3-3-8 PC4000 (Micron)
does it use these chips that you are talking about here? If not can you please point me in the correct directions and I am sorry for posting in the wrong forum

[gsan]

is it bh5 or ch5? although the sticks just 3500 without A/AK2/K2, but from cpu-z, it shown 200 @ 2-3-38, 217 @ 2.5-4-4-9 and different from what I found.

"HyperX PC 3500 (rated 2-3-3-7 @ 433Mhz, 2-2-2-6 @ 400Mhz, old revision) (KHX 3500) --chip--> Winbond BH-5 (maybe relabeled)"

http://img.photobucket.com/albums/v62/jasonloh/KingstonHyperXResized.jpg

http://img.photobucket.com/albums/v62/jasonloh/HyperXCPU-Z.jpg

[funkflix]

Did u tried 200MHz 2.0-2-2-5 2,6/2,7V?

[gsan]

Did u tried 200MHz 2.0-2-2-5 2,6/2,7V?

the ram is not mine but is someone else, and i'm going to buy from him. i just wanna comfirm before deal with him.

[Bob21]

2.5v is BH-5

2.6v is CH-5

[skinnie]

ppl found some old winbond mems and this is what it says on the chips..can anyone tell me if they are bh5 or something like that?
w942508BH-75 it has winbond logo..and it says too 233WD and in other chip 234WD they are from transcend

[caesarean]

2.5v is BH-5

2.6v is CH-5

YES !!!

[chefnr1]

Corsair xms v1.1- 2 x 512 bh-5 winbond 282mhz @ 2,0-2-2-5 , 3,7v on DFI U-D

[largon]

ppl found some old winbond mems (...)
w942508BH-75 (...)It IS the Winbond BH chip but binned for 7.5 nanoseconds (= 133MHz / DDR266) instead of 5ns as for BH-5 or 6ns for BH-6.

[deadlock7]

ppl found some old winbond mems and this is what it says on the chips..can anyone tell me if they are bh5 or something like that?
w942508BH-75 it has winbond logo..and it says too 233WD and in other chip 234WD they are from transcend

They don't overclock dude.I'd tried a pair of them..:(

[skinnie]

They don't overclock dude.I'd tried a pair of them..:(

well already bought them..I saw this http://www.xtremesystems.org/forums/showthread.php?p=1864331#post1864331

and other threads...sayin that with 3.3v for example..it could give 2-3-2-6 2240mhz

[stunned_guy]

2x256 mb TwinMOS PC3200 old BH-5 @ 291 mhz @ 3.95 v cooled by air
312we is the week ;)

http://img453.imageshack.us/img453/7640/twinmos2x256pc320029115jh4.th.jpg (http://img453.imageshack.us/my.php?image=twinmos2x256pc320029115jh4.jpg)

vaildation is 300 mhz @ 4,01 v (http://valid.x86-secret.com/show_oc?id=144706)
testetd on dfi sli-dr

[skinnie]

ppl this ram http://www.hardware.fr/medias/screenshots.php?id=IMG0006567 but in the pc3200 version is bh5 or bh6? the owner says it does 250@2.8v :S @2-2-2-3

[Drager2]

BH-5 "303we" 2.0-2-2 3.3v 242mhz (noname 3200 2*256mb@865PE)
*Asus P5P800 vovdimm=vio, S&M stable.

[loopy83]

Hello,
are there any BH5 Chips with a modified label?

maybe
Twinmos 0402D TMD7608F8E50D,
TwinMos 0448D TMD7608F8E501 or
TwinMOS 0449D TMD7608F8E50I

or does all these sticks have Powerchips on PCB?

Or have all old BH5 the Winbond Logo??