Problems with Clockgen/SetFSB and P4C800-ED

[Naughtyboy]

As the topic say I got problems when using either Clockgen or SetFSB on my P4C800-E D ....when I have set the values I want...no matter if I choose 1mhz or 20mhz...it hangs my system after a couple of seconds...then I get BSOD it says something about something wrong in the kernel. Can´t realy remeber.

I tried to reinstall the system...but still the same...and I use Srp1a and lates Intel inf.Utility.
And I also use bios 1016...the mobo came with 1014 and I had same problem there.

I have also tried to play around with bios settings ...but didn´t came up with anything.

Anyone else had any similar problems...?!?!?!?!?

[Naughtyboy]

Anyone....!!!!!!!!!!!

Surely I can´t be the only one with this type of problem...

[cpulloverclock]

Originally posted by [NH]Naughtyboy
Anyone....!!!!!!!!!!!

Surely I can´t be the only one with this type of problem... there's nobody, I'm just a spirit

what's ur settings ?
fsb
ram timings
all
...

[CODE 4]

I had this happen with my new 3.2E. It is not being read as a 3.2, but as a 2.8 in the bios. When I run clockgen or CPUZ it crashes me. I assume that the reading error is also what is leading to the crashes. This was not the case with my old 3.0C or various other cpu's. Without knowing your specs I can not speculate as to what might be causing your problem. Post specs and someone might be able to clue you in.

[abo333]

Originally posted by [NH]Naughtyboy
Anyone....!!!!!!!!!!!

Surely I can´t be the only one with this type of problem...

Please try the new version of SetFSB.

SetFSB for P4C800 Ultra Version 1.5g
http://www13.plala.or.jp/setfsb/

[Naughtyboy]

I´ve tried all kinds of settings...everything on Auto and everything on manual.
I´ve also tried different verisions of both clocgen and SetFSB including 15g...but nothing works.

Currently my settings are:

Jumper Free:
Cpu Ext. Freq: 200mhz
Dram Freq: 200mhz
Agp/Pci: 66/33
Performance: Standard

Chipset:
Cas: 2
Ras: 3
Cas to Ras: 3
Precharge: 5
Burst: 8
Performance: Eanbeld
Dram Idle: Auto
Dram Refrsh: Auto

I´ve done the droop and vdimm mod...vcore set to 1,55 and vdimm to 2.8 when set to Auto in bios. VDDQ is 1.5

And as you se I havent OC anything yet...!!!

I just can´t figure this biatch out :(

[BuLkHy]

im havin the same prob...with a 2.8E...
can u raise ur fsb in ur bios?..
mine cant..
and restarts when i open clockgen in windows...
does p4c800 supports prescott?

[Naughtyboy]

I´m using a 3.4 Northy...and 2x256mb A-Data PC4000.

No problems raising the fsb from bios...but clockgen or SetFSB is a no go.

[Naughtyboy]

This is weird.
I throwed it all in my Mach II to day to see what I can get out of this sucker,

After everything up´n running I installed Mbm 5.3.5.1 .....now during the installation it asked me something about deleting a giveio.sys...that the system was currently using and because of mbm using it´s own driver it didn´t needed the file...so I went with it.

And after the mbm installation finished and everything configured....something told me to try clockgen angain....and it works perfectly...both clockgen and SetFSB.

Strange...!!!! :confused: :confused: :confused: