abit IC7-max3 p4 3.2 more pics

[warlock]

2
pics

[sinn]

in the future, combine these threads into one, dont make an invidividual thread for each picture you have, nice though

[afireinside]

Make one thread and is that a vapo?

[warlock]

yes.
vapochill pe
cpu temp -31c to -28c
{bios reported -4c}
fan1 80%
fan2 80%
condenser 100%
heater load 70%
compressor speed 3500 rpm
-------------------------------------
on full load -22c/ cpu -1c
-------------------------------------
overclock

cpu 230x16/ vcore 1.650v /mem 2.8v
front bus 921.3
P4 3.2c

so what do you think, can i go higher if {yes} please tell me how.

[shidokanjohn]

I think that -31c at cpu with vapo is very hard to be done...

[Karnivore]

Slow your memory using the dividers (temporary) to remove memory from the equation, and try upping the FSB some more.

However by your already increased Vcore (1.75) I'm guessing you've already ran into stability issues?

What memory are you using?


If your memory is capable, you have limited options to increase CPU speed.

raise fsb, if unstable cool more, or add Vcore, past this very little you can do.

[warlock]

Karnivore


Was playing painkiller f about 20min, and them the system started to beep.
It did not lock me out; I quiet the games and check sys status
cpu 11c
vapo -17.5c
All the fans are disable

any Q

[Phyrox]

-31C with a vapo pe? on r134a that is immpissible. unless ur using r404a...my pe did -20C idle

[Karnivore]

Originally posted by warlock
Karnivore


Was playing painkiller f about 20min, and them the system started to beep.
It did not lock me out; I quiet the games and check sys status
cpu 11c
vapo -17.5c
All the fans are disable

any Q


I think your best bet at this point is to run some system stress tests and try to confirm stability. Why the added Vcore? was that needed to regain stability at your current clocks? at what point does default Vcore become insufficient?

Just trying to get a feel for system stability and what all you've done so far..

[warlock]

o.k

bear w me; sorry f my typeing..

in bios setting i change the thead hold to 80, i had it set 30
i change back def 80, when back and play the game.
no beeping sound.

that one.

i so change the mem (Vcore) back to 2.7v it was set to 2.9v

that two.

here is the sys status from pcwiard 2004.

Front Side Bus Speed : 250.6 MHz
Bus Speed : 1002.5 MHz (QDR)
Memory Bus Speed : 250.6 MHz
Vcore : 1.78 V
Type : DDR-SDRAM PC4000
Frequency : 251 MHz
FSB/DRAM Multiplier : 1/1x
Channels : Dual
ECC Diagnostic : No
CAS Latency (tCL) : 3 clocks
RAS to CAS (tRCD) : 4 clocks
RAS Precharge (tRP) : 4 clocks
Cycle Time (tRAS) : 7 clocks

the mem i hive Corsair xms PC4000pro w/led light.

at this time the system is very stable; i can play all the games with no problems.

at full load vapo temp -17.5c cpu is 11c
my fx5950 temp at full load, is about 34c

did i miss any thing?

p.s.
is possable to go high then 250fbs, would that put in about 4.2 to 4.5hz
i know it sound crasy, but can it be done.
with vapochill its a 160w unit right now i'm at -31c and cpu is -3c.
what do you think....

[Karnivore]

Originally posted by warlock
o.k

bear w me; sorry f my typeing..

in bios setting i change the thead hold to 80, i had it set 30
i change back def 80, when back and play the game.
no beeping sound.

that one.

i so change the mem (Vcore) back to 2.7v it was set to 2.9v

that two.

did i miss any thing?

p.s.
is possable to go high then 250fbs, would that put in about 4.2 to 4.5hz
i know it sound crasy, but can it be done.
with vapochill its a 160w unit right now i'm at -31c and cpu is -3c.
what do you think....


4.2+ is indeed possible, I'm sorry though, I simply cannot understand your #1, wth is thread hold?

I'm venturing a guess and saying you upped Vcore after the beeping in windows, as well as reducing your memory voltage? is that correct?

I would have to say playing painkiller is a somewhat less than optimum stability test.

You should really consider Evaluating your complete system and testing for stability. Just because you have PC4000 memory does NOT automatically say it will run DDR500. I would suggest setting everything back to default, then 5:4 on memory, and up your FSB slowly and test for stability, only increase your Vcore when needed. once you find max processor OC, then move on to memory, again test for stability, and compensate as needed with voltage, or speed reduction.

[warlock]

thank you..

#1 That's " thead hold" / in bios, if cpu temp pass
more then 70c it will shutdown.
i read this in vapo menual, it say to set to 30c
any way thanks f reply and for help....
i ran prime95, wait it f and hour no problem report it
sandra 2004 all test, the same no errors .
the only thing is vapo temp idel is -29.5c, full load at -17.5c and stable...

thanks f info...

[Manoj]

Originally posted by warlock
Karnivore


Was playing painkiller f about 20min, and them the system started to beep.
It did not lock me out; I quiet the games and check sys status
cpu 11c
vapo -17.5c
All the fans are disable

any Q

That must be your Pwr temp or something that the IC7 Max3 has. If it goes over 30 degrees C it beeps.

The mofsets are getting hot.

[warlock]

yea

i fix the problem.
it was in bios setting; the shutdown thead hold for cpu, it was set to 30c instead of 70c temp cut off
pws tru 550w 40a on 12v good power

[Shane5578]

i got similar setup as you.

i have these settings...

Reset CMOS

Load Optimised Defaults

Soft Menu
-Userdefined
-FSB 200
-PSB800 strap
-1/1 Ratio
-Fixed Lock
-AGP at 66mhz (higher if possible)
-VCORE 1.55v
-VDIMM 2.8
-VAGP 1.6

Advanced Bios
-Onscreen Branding Disabled

Advanced Chipset Features
-Manual
-2.5-7-4-4
-AGP 256meg
-Cycle Time set to normal
-tRDA set to Disabled
-CPC set to Disabled

Save and RESET

Run Prime95
Run Clockgen to increase FSB in small increments