prommy mach I will not start !!!

[PytonOrm]

hi there... i have a big problem with my prometeia mach I it will not start correct.. when power switch is on the compressor will shut down after 10-20 seconds... it´s gonna piss me off :mad: i haved programmed the display wrong i thing "A misstage" then the ST2 and P2 is lost i can´t programmed it right when these is lost... ST1 is set to - 28 right now and P1 set to 13

correct settings St1 - 20 + P1 = 13
St2 - 33 + P2 = 13

how in hell i got these P2 and St2 back ????? please :toast:


:confused: i will not buy new one for this.....


forgot this ?? what it does setting PRG + SEL if i put this all time in 10-15 seconds i get "range 0-120" tell me your config please......

[Rancidelephant]

is it shutting down due to high temperature ?

tried booting with it not connected to cpu, put the stock hsf on that ?

iirc the default settings are in the back of the manual.

sorry if thats absolutely no help :)

[PytonOrm]

is not shutting down due to high temperature at all.... from start i say it take 10-20 sec from i push the power switch on case.. i have lost all my setting in display on it !!! Please answer :(

[Rereg]

Possibly a cpu problem, rather than a prommie problem?

[TheDude]

If I understand your post correctly, your problem is that you have lost your ST2 and P2 settings? Have you tried this:

Hold down "SEL" for a few seconds; the display starts showing "St1"; release "SEL"; the actual value of St1 now flashes; press Up- or Down Arrow until you reach the desired new value; press "SEL" to confirm and enter this new value for St1; having confirmed St1 the display shows "St1" for a few seconds, and then its current value begins to flash; press Up- or Down Arrow until you reach the desired new value, or just; press "SEL" to confirm the new or unchanged value for St2; the display goes back into normal operation mode, and shows again the value measured by the probe.

To modify the factory-set and default hysteresis for the Reset signal and Fan-speed (P1 and P2); hold down "PRG" for 5 seconds; the display starts showing "P1"; press "SEL"; the actual value of P1 appears in the display; pressUp-or Down Arrow until you reach the desired new value;press"SEL" to confirm and enter the new value; press Up- or Down Arrow until the display shows "P2"; press "SEL"; the actual value of P2 appears in the display; press Up- or Down Arrow until you reach the desired value; press "SEL" to confirm the new or unchanged value for P2; press "RPG" to store all changes and return to normal working operating mode.

I hope that is the info you wanted? ;)

[PytonOrm]

The dude

:( i only get P1 , 14 , 25 , 26 , 27 ,28 and P2 is not coming however i push the bottom... even ST2 is gone :( by the way :) if i buy new display it will work ???

[TheDude]

This is after you select new P1 value?

[PytonOrm]

i will take a pics now

[PytonOrm]

This is P1 and it set to 13

http://w1.565.telia.com/~u56506172/pic01.JPG


http://w1.565.telia.com/~u56506172/pic02.JPG


http://w1.565.telia.com/~u56506172/pic03.JPG


http://w1.565.telia.com/~u56506172/pic04.JPG


these setting i got only !!!

[TheDude]

So after you set P1, you can"t you set P2 because it never shows up?

[PytonOrm]

Thedude

yepp... never shows up :( even ST2

[TheDude]

So, you can set the highest temp, but have no way of setting the lowest temps.
I'm at a loss...I would suggest you send all this detailed info to nVENTIV in an email with your serial number and any setup or other type changes you might have made to it.
Hopefully they have seen this before and will be able to help you.
Please post if they have any suggestions as to a fix.