radeon 9700pro

[komer]

i have problem tat my radeon does not get electricity from ATX!the pins of conector on vga are moving!i need some scheme where i can see where can i put electricity on other place!tnx!hope u understand

[Hell-Fire]

Can you post a picture of exactlly what you are referring to?

[komer]

iam looking for picture where can i see resistors,transistors,chips etc

[komer]

http://www.viperlair.com/images/reviews/video_graph/ati/aiw/9700pro/power.jpg this connector seems to be broken or somethong so i looking for alternative where can i connect wires with power on radeon9700pro!tnx

[komer]

you can se 2 black,red and yellow wire!i want to connect them on other place (not on that broken connector),thats alternative but i dont know where i can connect wires!

[komer]

i would be nice that u can help me!!!

[G H Z]

Hey just flip the card over. See the back where the four pins from that connector go thru the pcb?

Easy!

[komer]

that is the problem i cant see where the wire goes through pcb!i see but not clearly

[blinky]

its not hard, just find the 4 big things of solder on the back then match them up with the wires coming to the molex

[bachus_anonym]

just like on the pic below...

right-down corner.... 4 fat soldering points in vertical....
first from the top of the pic is 12v, then ground x 2, and 5v...

http://www.speakeasy.org/~michasmisiek/R9800P/done_right_small.jpg

[komer]

ok i understand!and what if it doesnt work?where else can i connect molex wires?

[komer]

what are this two black and red wires?is that mod?

[Karnivore]

Here is a picture taken of the backside of a 9700P directly opposite the power wire connector. The colors are coded to wire placement and the solder points are directly to the right of the colored lines.


Edit: If connection at these points does NOT work your card has other problem/s

[komer]

is ok!tnx!but i have multimeter(voltmeter,ampermeter,resistormeter etc) so i checked and yellow wire is ok but on red wire it doesnt have power!where can i connect red wire(alternazive) in my case!i dont know where to connect red wire?can u help me

[Karnivore]

Umm, anywhere along the circuit trace directly connected to the pin, if your connection pin is not providing power to the board, yet the wire has voltage you may have a poor solder connection to the board, perhaps just resoldering the pin to the trace.

[komer]

if i know where t oconnect the red wire i would be happy!on some chip or?do u have picture or smthg so u can send me on mail or post it here?

[komer]

i found 1 problem!seems to be that i have a 2 problems!the condenzator(capatitor i thin is call like that) was how can i say(1 pin was connected and 1 isnt conncted!i connect both pins and the cooler starts to work!what shall i do next?i dont have picture on monitor?

[G H Z]

Use the VM to check the continuity(set it to beep), of the power/ground pins in the back, to the corresponding pins on the molex connector.

This will verify their proper connection. Maybe wiggle it a bit when doing this to see if there is a loose connection. Then check to see the you are getting power thru the molex that you attach to the card.

Is the card damaged? Do the traces coming from the pins look damaged?

[komer]

card is not damaged!i have power on molex from psu!but i think that the molex connector on card is broken!red wire does not give power to graphic card,but yellow does!the cooler working,so i think that the vga doesn´t have enough power that vga can woorking propetly!