AMD PHII X4 955BE ES + HD4870X2 CFX 36k 3D06 46k 3d05

[[XC] gomeler]

First off I'd like to thank AMD for being great hosts. You guys knocked this one out of the park. Simon Solotko and Peter Hardman were great and Aaron Schradin's LHe pot was insane. Huge props to Brian and Vince, you two are some stellar benchers :up:

Over the three days I focused mainly on 3D05/3D06. Compared to the CPUs that Vince and Brian were using, mine was relatively tame. I worked for two days with the Gigabyte 790FXT-UD5P to get my northbridge above 4GHz but to no avail. In the last 4 hours of benching on Friday I switched over to the Asus M4A79T-Deluxe that Vince had prepared for LHe and that board screamed. I've got a mix of results below.



AMD Phenom II X4 955 BE ES, Gigabyte 790FXT-UD5P, Corsair Dominator DDR3-1800C7 D9GTR, Corsair HX1000, HD 4870x2 CFX

3D03 143678 CFX 800/950

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/3D03-CFX-143678.jpg

3D05 46151 CFX 800/950

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/3D05-CFX-46151.jpg

3D06 35615 CFX 800/950

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/3D06-CFX-35615.jpg

3D06 31109 Single 800/950

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/3D06-Single-31109.jpg

CPU-Z @ 6547MHz

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/CPUz-6547.jpg

SPi 1M @ 6490 10.812s

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Super-Pi-10-812.gif

SPi 32M @ 6090 11:54.563

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Super-Pi-11-54-563.gif

All these results were terrible due to the low NB and I was still testing the CPU.

AMD Phenom II X4 955 BE ES, Asus M4A79T-Deluxe K|ngp|n prep edition, Corsair Dominator GT DDR3-1866C7 Elpida HyperIC, Corsair HX1000, HD 4870x2 CFX

3D05 46574 CFX 800/950

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/3D05-CFX-46574.jpg

3D06 36100 CFX 800/950

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/3D06-CFX-36100.jpg

I ran out of time here, had to pack up quickly and go catch my flight :(

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Vince-and-LHe-2.jpg

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Vince-and-LHe.jpg

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/900-Gallon-LN2-Tank.jpg

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Hardman-and-900-gallons-of-LN2.jpg

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Benching-Complete.jpg

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Benching-Complete-2.jpg

Real benchers bench upside down.

[carpo93]

great run

[Zeus]

Awesome runs man! :up: Shame you wasted that much time on that gigabutt mobo but it seems you made up well with the Asus board!

Do you have more pics?

[dinos22]

nice man....really nice scores

how come you ran your GPU cores at 800?

could they not do more?

so this was LN2 only?

[[XC] gomeler]

Awesome runs man! :up: Shame you wasted that much time on that gigabutt mobo but it seems you made up well with the Asus board!

Do you have more pics?

no more pictures. I was too busy tearing apart motherboards :(


great run

thx!


nice man....really nice scores

how come you ran your GPU cores at 800?

could they not do more?

so this was LN2 only?

Vince was the only one on LHe. My GPUs do 860/950 all day long but I had troubles with the fans dropping to 20% after CPU1 and crashing out so I just used CCC and set to 800/950. Waiting on a decent 955 so I can bench at home with the GPUs on -40C alcohol :up:

[carpo93]

now i'm testing my 955 on air
then i'll go to ln2 soon

but i've 3 4890 not 2 4870x2

[Movieman]

Sounds like you had a great time with good people.
Props to AMD for this one!:up:

[G0ldBr1ck]

Nice run Gom. Shame you been having such bad luck with boards. waching all this fun you guys had has got me calling all over the state trying to score some LHe wich is proving to be dificult not to mention the $$$!

[Solarfall]

http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Hardman-and-900-gallons-of-LN2.jpg


OMG i want that thing on my back yard. jeezz thanks mate im definitely gonna have wet dreams tonight :ROTF:

[Slappa]

Glad you made up with the ASUS board and pulled ahead at the very end gom. Especially after watching you struggle and try at least 3 different setups with the UD5P.

Now that I have 2 of the gigabyte boards I think I'm gonna have to swap one for that ASUS board. Looks to do better with the chips altogether.

[chew*]

Nothing wrong with the board Slappa, just requires a little more work and time on the board to learn its tricks. Gomeler has had maybe 4-5 days max on the board, I'm sure he will figure out its secrets soon enough. We have had the NB up to 4700 on the gigabyte.....4600 is the max we have had the asus.....I had the NB at 4300 at this event, I ran out of multis and didn't feel like dropping ram divider to crank HT as the system was dialed in.

For reference speed is not always relative to performance.....4300 NB on one board can be equal to or greater to 4500 on another board..........with the f3L bios the MRL is pulled in very very tight, asus is known to "loosen" things up to achieve higher "speeds"

[[XC] gomeler]

now i'm testing my 955 on air
then i'll go to ln2 soon

but i've 3 4890 not 2 4870x2

3 HD4890 will be impressive. Can't wait to see your results :up:


Sounds like you had a great time with good people.
Props to AMD for this one!:up:

I had a blast. Now we just need to get you benching a Phenom II rig, all you have to do is keep the pot full of LN2 :D


Nice run Gom. Shame you been having such bad luck with boards. waching all this fun you guys had has got me calling all over the state trying to score some LHe wich is proving to be dificult not to mention the $$$!

Thanks man. LHe honestly is too expensive to use even for extreme benching. It was a lot of fun to watch, but I'd rather stick with LN2 and be more cost efficient. I think the LHe bill for the three days was around $5k :eek:



OMG i want that thing on my back yard. jeezz thanks mate im definitely gonna have wet dreams tonight :ROTF:

Me too! I'd settle with a smaller one, that one holds 900 gallons. I'll take a 200 gallon tank to start.


Glad you made up with the ASUS board and pulled ahead at the very end gom. Especially after watching you struggle and try at least 3 different setups with the UD5P.

Now that I have 2 of the gigabyte boards I think I'm gonna have to swap one for that ASUS board. Looks to do better with the chips altogether.

Thanks for the help piecing together that last 790FXT-UD5P. I really wish I had swapped boards much earlier, the ASUS BIOS/board was just slightly more mature and resulted in slightly better performance.


Nothing wrong with the board Slappa, just requires a little more work and time on the board to learn its tricks. Gomeler has had maybe 4-5 days max on the board, I'm sure he will figure out its secrets soon enough. We have had the NB up to 4700 on the gigabyte.....4600 is the max we have had the asus.....

I've been benching with that board for a while actually. You are the only person I know that has been pushing NB on that board. Even Peter Hardman was stumped by it. The Asus M4A79T-Deluxe loves my Elpida though, so I went to Fry's today and picked one up for testing. Bought 2 4870x2 waterblocks also, going to put the cards on chilled water next week with a retail CPU :D

[chew*]

For reference NB clocks best when memory is stable and IMC is happy.....IIRC you were using rear slots....the gigabyte works best with elpida in front slots Or at least thats what my testing has yielded. Give it a shot. Check out the gigabyte thread, Msimax is working with elpidas atm ;) Not the only person, Msimax has been pushing the NB as well....he's also worked closely with me so knows most of the tricks.

[[XC] gomeler]

For reference NB clocks best when memory is stable and IMC is happy.....IIRC you were using rear slots....the gigabyte works best with elpida in front slots Or at least thats what my testing has yielded. Give it a shot. Check out the gigabyte thread, Msimax is working with elpidas atm ;)

I was using D9GTR like you and copied your settings. I'll stick with the M4A79T-Deluxe for right now :)

[3oh6]

good looking stuff Chris :up:
should look a whole lot better with the GPUs on chilled water, can't wait to see the results.

[chew*]

gomeler;3805538']I was using D9GTR like you and copied your settings. I'll stick with the M4A79T-Deluxe for right now :)

True but we forgot to take one thing into consideration.....I was using 2 sticks binned from 6 sticks total, and had them Id'd right down to which slots they needed to be installed in for max clocks...........they probably needed to be toned down a tad to say 1660-1680, the 1720 I was running was so close to the edge of stability its not funny.

This was msi's chip on the gigabyte.

http://www.xtremesystems.org/forums/showpost.php?p=3748989&postcount=19

I would say just sit down with it for awhile man, you will figure it out, don't count it out quite yet ;)

[Slappa]

Nothing wrong with the board Slappa, just requires a little more work and time on the board to learn its tricks. Gomeler has had maybe 4-5 days max on the board, I'm sure he will figure out its secrets soon enough. We have had the NB up to 4700 on the gigabyte.....4600 is the max we have had the asus.....I had the NB at 4300 at this event, I ran out of multis and didn't feel like dropping ram divider to crank HT as the system was dialed in.

For reference speed is not always relative to performance.....4300 NB on one board can be equal to or greater to 4500 on another board..........with the f3L bios the MRL is pulled in very very tight, asus is known to "loosen" things up to achieve higher "speeds"

Not that there is anything wrong with the board, but it is a drag to work with out of the box. Of course you spent countless nights figuring out tweaks for this board. I think I'm going to have to do the same when I get home. I just don't think my board likes my G.Skill Pi set that I have in there.

Anyone know what chips are in the G.Skill 1333MHz 7-7-7-18 1.6v set? They are actually pretty good OCers, mine go up to 1600MHz 1.6-1.65V @ 7-7-7-18 and am sure I can push them further.

and @ Gomeler

No problem. I just watched your troubles for too long and felt I needed to help get you up and running faster with that last one.

[cdawall]

very nice runs sorry the GB issues loving my asus M4A78T-E

[msimax]

nice results [XC] gomeler

[Hazzan]

Cool Action ....Cool Result ......:up::up:

[Brian y.]

Very nice scores Chris:clap:

Looking forward to some more killer 3D action and even maybe a little PC Mark 05 actionhttp://img39.imageshack.us/img39/9585/ocx0937.gif

[k|ngp|n]

:up: :up: Nice last minute session eh? Good stuff..

[carpo93]

gomeler;3805515']3 HD4890 will be impressive. Can't wait to see your results :up:


i think i'll bench on 2nd june(celebretion of repubblic here in italy, so i'm not going to school) and 6-7-8nd june

i've 50l of ln2 :D


for you wich is the best bios for m4a79-t?

[Lightman]

Congrats on your scores [XC] gomeler!

Following your footsteps I will attempt to bench upside down next time :p: Sick idea!

Also that LN2 tank would look perfect in my garden! A bit of engineering and one would make nice 24/7 cooling solution for Phenom II :rofl:

[leonarderman]

Wow! I see it's easy to get 36k scores in 3DMark06! :up:

[bazx]

thats got to beat dunking cascades in tubs

well done mate sure looks a great deal of fun

[[XC] gomeler]

good looking stuff Chris :up:
should look a whole lot better with the GPUs on chilled water, can't wait to see the results.

Thanks man. I have high hopes for these GPUs on chilled liquid. Should have results in ~2 weeks.


very nice runs sorry the GB issues loving my asus M4A78T-E

Thanks. Gigabyte just needs to figure out their BIOS issues, otherwise a solid board.


nice results [XC] gomeler

Thanks, more to come!


Cool Action ....Cool Result ......:up::up:

Thanks!


Very nice scores Chris:clap:

Looking forward to some more killer 3D action and even maybe a little PC Mark 05 actionhttp://img39.imageshack.us/img39/9585/ocx0937.gif

Definitely going to take you up on that offer. Might give Phenom II a shot at some PCM05 testing later this week :up:


:up: :up: Nice last minute session eh? Good stuff..

Totally worth it, now I've found the board I'll use this week. Coating it in lacquer right now :up:


i think i'll bench on 2nd june(celebretion of repubblic here in italy, so i'm not going to school) and 6-7-8nd june

i've 50l of ln2 :D


for you wich is the best bios for m4a79-t?

I don't even know what BIOS I used, we pulled the board out of the box and fired it up :shrug: I hope your bench session goes well, looking forward to some great score. I have 180L being delivered on Wednesday :cool:


Congrats on your scores [XC] gomeler!

Following your footsteps I will attempt to bench upside down next time :p: Sick idea!

Also that LN2 tank would look perfect in my garden! A bit of engineering and one would make nice 24/7 cooling solution for Phenom II :rofl:

Thanks!


Wow! I see it's easy to get 36k scores in 3DMark06! :up:

That took 3 days of benching :ROTF:


thats got to beat dunking cascades in tubs

well done mate sure looks a great deal of fun

Sadly I'm back to dunking this thing. Hopefully that thread/cascade will be finished up shortly :up:

[FlanK3r]

congratulations man. And i love AMD, great PIIs :)

[JamesBong420]

WOW!!! 36k!!!! good job m8y.... :p::up::D massive destruction on hwbot this weekend.. :up::clap:

[[XC] gomeler]

WOW!!! 36k!!!! good job m8y.... :p::up::D massive destruction on hwbot this weekend.. :up::clap:

No joke, it seems everyone planned their hwbot assault this weekend. My 06 score has slipped from 3rd to 4th already :p:

*arnold voice*

I'll be back

[dinos22]

gomeler;3805207']no more pictures. I was too busy tearing apart motherboards :(



thx!



Vince was the only one on LHe. My GPUs do 860/950 all day long but I had troubles with the fans dropping to 20% after CPU1 and crashing out so I just used CCC and set to 800/950. Waiting on a decent 955 so I can bench at home with the GPUs on -40C alcohol :up:
LOL yeah i know all abou that
what you should have done is pull out the fan cable and bend the pin that connects to blue cable for some 100% fan ownage :D

[dinos22]

gomeler;3805163']
http://gomeler.com/pic/AMD%20Phenom%20II%20OC%20Session/Hardman-and-900-gallons-of-LN2.jpg

http://weblogs.newsday.com/sports/watchdog/blog/dallas_cheerleaders.jpg

boioioioioioioing :D

[chew*]

LOL and people say, but you can't game on ln2 ......Wrong with that tank you can :D I actually pondered humping it but pete was right beside me.

[dinos22]

LOL and people say, but you can't game on ln2 ......Wrong with that tank you can :D I actually pondered humping it but pete was right beside me.

meh
if Thomas(Pt1t) was there it would be a hump-a-thon out there

:D

[tiborrr]

Excellent work Gom, too bad for NB issues. Will be better after some more 'training' at home :up:

[dpa]

get that NB up :D good luck on next 2k6 session.. dont kill my score ;)

[Pt1t]

meh
if Thomas(Pt1t) was there it would be a hump-a-thon out there

:D

On this want i can Drink beeeeeerssssss and dance on it :D

[[XC] gomeler]

LOL yeah i know all abou that
what you should have done is pull out the fan cable and bend the pin that connects to blue cable for some 100% fan ownage :D

I couldn't remember which was the sensor pin :D


meh
if Thomas(Pt1t) was there it would be a hump-a-thon out there

:D

I considered humping the dewar to pay homage to Thomas :rofl:


get that NB up :D good luck on next 2k6 session.. dont kill my score ;)

I'll be gentle :up:


On this want i can Drink beeeeeerssssss and dance on it :D

We needed you there to show us how it is done. Can you believe it, there was no beer at this event?!

[Oliver]

nice to see you guys pushing together , brings back what oveclocking is about for sure,

the scores are tasty and i cant wait to see what you will bring from your sleeve once settled with the setup and rocking max

keep pushing it