View Full Version : [OCTH] GTX 295 + Tek9 warm up on dice
Achill3uS
03-13-2009, 02:50 AM
hey guys,
yesterday ive inaugurated my new Tek9 5.0 pot (http://img3.imageshack.us/gal.php?g=tek91.jpg) with some dice action, and i can tell this unit is just amazing by holding temps :) sadly i had some problems with the card after one hour benching so i couldnt continue, it was not able to run any 3D on even stock clocks, dunno why coz i insulated very well... anyway now its dry and works again, waitin for the ln2 run :D
DFI LanParty UT X58-T3eH8 (0217bios)
Intel Core i7 965XE retail (3835A577)
Team Xtreem 3GB DDR3-1866 CL9
XFX GTX 295 2GB
CSX SLC 32GB SSD
Silverstone DA 1200W
k|ngp|n F1EE & Tek9 5.0 @ -60C
CPU voltage: 1.50v
NB voltage: 1.10v
CPU PLL voltage: 1.80v
QPI voltage: 1.63v
RAM voltage: 2.03v
GPU voltage: 1.25v
http://img16.imageshack.us/img16/5859/benching295onsubzero.jpg
http://img27.imageshack.us/img27/5803/3012106.png
http://service.futuremark.com/compare?3dm06=10311956
max validation @ 4994MHz (http://valid.canardpc.com/show_oc.php?id=525784)
thanks,
bala
850, sounds about right.. I tested yesterday with LN2.. 890 is max.. 1.2v in voltage tuner. over that = red light.com :(
did you encounter red light?
ADAM1337
03-13-2009, 03:47 AM
Very nice scores.
W8ing for ln2 bench.:yepp:
ZoLKoRn
03-13-2009, 03:57 AM
well done! m8 and greats score from first start :up: waiting to see more on really benching ;)
Kabauterman
03-13-2009, 04:25 AM
nice score, but I think your card isn't good over all, -60 @ 1,2V and only 850 MHz ?
keep pushing it man! and try out Vantage ;)
(1,3V and card clocks up to 1000 are possible)
Vantage produces the lowest Phase output so OCP don't comes on Vantage...
carpo93
03-13-2009, 04:29 AM
nice score
Achill3uS
03-13-2009, 07:11 AM
850, sounds about right.. I tested yesterday with LN2.. 890 is max.. 1.2v in voltage tuner. over that = red light.com :(
did you encounter red light?
i have some non-public mods so no red light problem with even more volts like 1.30v+ but it not helped for my card at all.
Very nice scores.
W8ing for ln2 bench.:yepp:
thanks ADAM, me too :D
well done! m8 and greats score from first start :up: waiting to see more on really benching ;)
thank you m8, my dewar is still under repair (re-vac) so im on dice till months, but lets hope i will got it back in few weeks :up:
nice score, but I think your card isn't good over all, -60 @ 1,2V and only 850 MHz ?
keep pushing it man! and try out Vantage ;)
(1,3V and card clocks up to 1000 are possible)
Vantage produces the lowest Phase output so OCP don't comes on Vantage...
haha i know it mate, this card is kinda banana :D i hope will do something around 900 on ln2 :rolleyes:
nice score
thank you carpo :)
iam starting to HATE these cards.. non public mods.. BLAH.
good luck on further benching!
Kabauterman
03-13-2009, 08:20 AM
same as on GTX 280 (20A Per Phase max)
but 280 has 5 Phases (100A per PCB) and 295 has 3 Phases (60A per PCB)
OCP suxxs!
Solarfall
03-13-2009, 01:24 PM
could it be that the graphic driver is holding you back? .. i remember when i did my last vantage test with 2 260gtx cards the 182.xx drivers sucked balls.. only the 180.48 was descent and was able to push the cards much further.
Good job Bala mate, hope youll get the dewar sorted out soon. Nice & clean setup :yepp:
xbrian88
03-14-2009, 05:59 AM
good score my friends
Achill3uS
03-15-2009, 01:52 PM
thank you mates M3kk, loc.o, xbrian88 :up:
iam starting to HATE these cards.. non public mods.. BLAH.
good luck on further benching!
actually ive heard about redlight with stock card only around 1.29v so it depends on, like oc potential i bet.
for me more volts than 1.20-1.25v not gain anything so i think if you have a bad card mod not helps with a good card you dont need it :) and thanks!
could it be that the graphic driver is holding you back? .. i remember when i did my last vantage test with 2 260gtx cards the 182.xx drivers sucked balls.. only the 180.48 was descent and was able to push the cards much further.
ive seen some other guys also stuck below 900 with ln2 so i guess not, i used 182.06 btw
Oliver
03-15-2009, 02:13 PM
good start bro , the unit is just amazing ...
keep pushing it
George_o/c
03-15-2009, 10:06 PM
Nice on mate :up:, in spite of the GTX295 "banana" version :D :( Hope you can sort out your problems with the dewar soon :)
Achill3uS
03-17-2009, 12:09 AM
thank you bro's, till i didnt got my dewar back as our plans at the weekend we will push it more on different cpu and vga together with jugeen :)
k|ngp|n
03-17-2009, 09:33 AM
Always love your work man..keep pushing. Of course the setup looks amazing but I'm biased :D. From what I heard the software voltage adjustments work good dpa, guess not.
hardmod is def the way 2 go! software volting takes a little skill out of overclocking
Oliver
03-17-2009, 10:37 AM
Always love your work man..keep pushing. Of course the setup looks amazing but I'm biased :D. From what I heard the software voltage adjustments work good dpa, guess not.
for THC and i , the soft works flawless ... no problems what so ever , accoured during weekend session ...
hardmod is def the way 2 go! software volting takes a little skill out of overclocking
ya , its prefered to have such control on hardware level , but from personal experience , soft on it have worked very well
Achill3uS
03-18-2009, 02:00 AM
Always love your work man..keep pushing. Of course the setup looks amazing but I'm biased :D. From what I heard the software voltage adjustments work good dpa, guess not.
thanks for your words Vince, and there is nothing bad with your bias, wich is good is good :D
hardmod is def the way 2 go! software volting takes a little skill out of overclocking
thanks Goddy, there is nothing bad with softmods, easy to use almost without any risks, but ofc hardmod is always a better solution for more precise voltage adjustments and so on :)