E8600@5200mhz under water

[M-XXXX]

Because cold days/nights are here, I had some happy times with my E8600 under water OC:D

E8600 Q820A606
Gigabyte UD3P motherboard
Cellshock 1000 cl4 rams
Water cooling (radiators were outside, on cold air)

As first: Resaults aren't for best SuperPI time, but just for max frequency.

I started with 1.568V and got to 5150mhz for SuperPI 1M

http://shrani.si/t/3z/k8/1tDp6idN/5150-pod-vodo.jpg (http://shrani.si/?3z/k8/1tDp6idN/5150-pod-vodo.jpg)


Then I went for higher voltage (Motherboard has some BIOS bug, because one level higher CPU voltage, has give me almost 0.08V more voltage) so i bench on 1.648V

http://shrani.si/t/3u/XE/1GxO8U98/5178.jpg (http://shrani.si/?3u/XE/1GxO8U98/5178.jpg) http://shrani.si/t/h/On/3LlhNiP7/5200-pod-vodo.jpg (http://shrani.si/?h/On/3LlhNiP7/5200-pod-vodo.jpg)

Temparature of water was about 1-2C, air outside had about -2C.

http://shrani.si/t/2X/EG/4gLn0Zmv/img7675.jpg (http://shrani.si/?2X/EG/4gLn0Zmv/img7675.jpg) http://shrani.si/t/2x/12L/4C8O774O/img7678.jpg (http://shrani.si/?2x/12L/4C8O774O/img7678.jpg)

Bench on:up:

[(TAT")]

:D Nice! This is what I get at water cooling (15'C water)
:clap:

http://forum.anti-x.org/attachment.php?aid=74474&k=b0ef7c37c85be23a464b69690400c5d1&t=1228059394&noupdate=yes

[WaterFlex]

Good job:D
But water temperature was 1-2. You can do more. Keep pushing chip.

[TheKarmakazi]

Nice OC! Tweak those pi runs!

I was able to take my 8600 to 5013Mhz for 3dmark vantage runs, using 1.59v (1M topped out at 5050Mhz). Using dryer tube ducting bringing in cold air from outside (with a 240CFM Delta)

89912

[M-XXXX]

Nice OC! Tweak those pi runs!
My point wasnt the best time, but only frequency.
Best efficiency that I got on this motherboard was about 45250, but its a bit weird- only one time- after bios reset I could get to only 46300??


You can do more. Keep pushing chip.
Probably only few mhz more, but I will try again (more antifriz and few C less:D)

[systemviper]

Hi, That i great, i will be setting up my PC's this week, I also have the UD3P and a E8600 and Q9650

I am in CT and we are getting some nice low temps too. :rolleyes:
I am going to put 2 rads right out side the window with a Bucket half full of antifreeze, I will have them on a separate loop with a Copper top GTX and D4 pump for some cold water fun.

Thanks for posting your settings, that will give me a good start with the E8600.
The Q9650 I already had @ 4.86Ghz @ 1.55v on air :surf: with a Xig direct touch, so I am hoping for some quad action @ >5GHz if i am lucky.

Nice work :up:
Real nice Super Pi's


Is there any issues with putting 2 radiators in a bucket 1/2 full with antifreeze, This is all a first for me, so I was wondering what to look out for.

[drnip]

Nice!!!

[Bullet92]

Nice benching... Now when you maxed out CPU on water go to something more extreme if you can. And lets do some serious 1M time now ;)

[flesheatinvirus]

I am pretty happy with my 8600 also.This is on water with the chip on its own loop. Aquamark3 was at 5G:D

[M-XXXX]

Nice benching... Now when you maxed out CPU on water go to something more extreme if you can. And lets do some serious 1M time now ;)
I allready have 5600 for SuperPI under SS:D


Is there any issues with putting 2 radiators in a bucket 1/2 full with antifreeze, This is all a first for me, so I was wondering what to look out for.
If you will put your radiators into antifrize you will have some problems:
First: If will be antifreeze below -10C(or something like that) water in radiators MAY freeze, and damage the radiators,
Second:You'r temparatures won't be so good if you won't mix the antifreze or in whatewer liquid are you goint go have radiators...

[HDCHOPPER]

very nice man !!

thats all a clocker needs is a 5.0 24/7 machine :D this year

[OC4/3]

Damm.........Seeing these E8600 under water doing 5ghz+ benchable make me even wanting it more!!:D
Officially jealous of this:rofl:

[M3kk]

Nice OC! Tweak those pi runs!

I was able to take my 8600 to 5013Mhz for 3dmark vantage runs, using 1.59v (1M topped out at 5050Mhz). Using dryer tube ducting bringing in cold air from outside (with a 240CFM Delta)

89912


I am pretty happy with my 8600 also.This is on water with the chip on its own loop. Aquamark3 was at 5G:D

What FPO guys? :)

[George_o/c]

So which E8600 batch is better ... ? Q820Axxx or Q822Axxx ?

From what I've seen so far, Q820Axxx is better @ air or water, but doesn't perform well on subzero temps ... enters Q822Axxx, which is great on subzero temps ...

Am I correct ? :shrug:

[quake6]

Yeap,as far as I known q822 is a better on subzero...

[SoF]

q822a435 seems to be the sweet stepping - I never saw so many good E8600 with one specific stepping again. also all q822a435 seem to love cold. I know a bunch of chips doing -150°C idle and good clockspeeds. my one is not too bad either and over at AF the best results in our team where all done with this stepping.

[George_o/c]

Hmmm, so I was correct :) The moment I buy an E8400 Q832Axxx (E0 stepping of course), I'm gonna start looking for a nice Q822Axxx E8600 (I need one good under cold, for some 3D benchmarking) ... In spite of the Q822Axxx you know some other "cold-friendly" E8600 batch ? First priority is temperature, then finding a nice chip ;)

[flesheatinvirus]

My chip is a 820A324 1.26vid which seems to run a little cooler then the lower vid EOs from what I have seen. I have not tried a 822 yet but this chip was an easy 5G on water with this P5K Prem. I think me needs Phase for this chip.

[fatguy1992]

Awesome :up:

I can't wait till its winter here :)

[George_o/c]

Thanks a thousand times for the information on Q820A324 flesheatinvirus. The latest E8400 batch though, has a lot of examples that can do ~5GHz on air 1M ... What benchmarks could you run with your E8600 @ 5GHz ?

[flesheatinvirus]

So far I have just done the Pi thing, Aquamark3 and Futuremarks 3DM01SE- 03- 05- 06 and Cinebench R10 all of which ran no problem at 5G, Cinebench R10 was about 11G. I will run more benchmarks and post the results. PD on this chip was 07/17/08 and its on its own PA 120.3 loop in pull with a Dtek Fuzion block. No Prime or Orthos just yet as I want to play. Soon this chip is getting a P5Q Deluxe and today I just got in my EVGA 280GTX with a EK nickel block to replace this 8800 Ultra which is certainly not pushin Brown just yet. I also have an older 745A576 CO 8400 that runs 4900 but these new EO 8600 chips are faster with less Vcore, they are the shad for the money right now. Here is 3DM06. http://service.futuremark.com/compare?3dm06=8995163:D

[George_o/c]

3D Mark 06 @ 5070MHz on water is :woot: :D
Nice chip my friend ;)

I'll go for two E8600s then ... :p Q820 for low clock challenges, and Q822 for real benching :yepp: :D I've already forgot about that Q832 E8400 :p:

[(TAT")]

Screen cap fixed...
:D

[M-XXXX]

(TAT")
What cooling? Becaue this voltage is quite high under water or air....:D

[TheGanG]

Nice OC! Tweak those pi runs!

I was able to take my 8600 to 5013Mhz for 3dmark vantage runs, using 1.59v (1M topped out at 5050Mhz). Using dryer tube ducting bringing in cold air from outside (with a 240CFM Delta)

That's pretty good man :)

[(TAT")]

(TAT")
What cooling? Becaue this voltage is quite high under water or air....:D

15'c water:D

[Nordling]

Nec 20WGX2 Pro White — awesom!

[drnip]

Had mine at 5200mhz yesterday on water as well. Got to love it!!! Vcore was roughly at 1.62v at idle though, still pretty good to me. Didn't have time to run any tests but will tonight.

5.2ghz Validation Link (http://valid.x86-secret.com/show_oc.php?id=455336)

http://i269.photobucket.com/albums/jj55/travisjcottrell/5200mhz.jpg

[flesheatinvirus]

Just got my 280GTX hooked up on water this weekend, here is a run of 3DM06 at 5100mhz.

[funkflix]

Nice results guys! :up:

Here my old E8600 Q820A5xx with 12°C water:

http://img388.imageshack.us/img388/3700/32mhy8.jpg

http://img238.imageshack.us/img238/7858/1m2rj1.jpg

http://img217.imageshack.us/img217/9725/05tu1.jpg

http://img136.imageshack.us/img136/2118/01ss1.jpg

[M-XXXX]

funkflix great resoults! Processor similar to my one. Its nice to see 5200 under water:D

[dami1stm]

I will receive a very good E8600 on aircooling, I post some screens when i receipt it. :D

[ToyTen]

He's getting that kind of CPU: http://www.jmax-hardware.com/forum/index.php/topic,1641.msg158936.html#msg158936

no need to get french to see what it goes about... Dami1stm ROCK IT please:D

[TheGanG]

E8600, one of the best Intel Chip. Overclocking easily up to 5.2GHz/S-Pi under stock fan + cold air
(10°C-15°C cold air with a good fan is more efficient than water cooling, tested!)

[noinimod]

Wow crazy clocks on the e8600. looks like they're well worth the premium over its little brothers

[s e r e n i t y]

Thats an impressive result under water!

[eva2000]

sweet clocks guys.. one of my E8600 Q820A599s on Fuzion V1 H20

E8600 Q820A599 *0464

Max CPUZ Validation @5146Mhz at 1.600v idle / 1.568v load
Super Pi 32M @5093Mhz at 1.600v idle / 1.568v load
Super Pi 32M @5025Mhz at 1.552v idle / 1.520v load


@5146Mhz

http://valid.x86-secret.com/cache/banner/438159.png (http://valid.x86-secret.com/show_oc.php?id=438159)

http://fileshosts.com/intel/DFI/DFI_DK_X48T2RSB_Plus/results/fuzion/E8600_Q820A599_0464/crucial/ballistix/8500naked/9.5x/333_800/AFE_541-650_5559-A-A-pla_30-a_1212_trrd3trtp4_1.5875_104-2.55-1.665-1.39_66766761_800200_1244_AA/eeeea_eaaaa/cpuz_valid_5146mhz.png

@5093Mhz - click image for full screenshot

http://fileshosts.com/intel/DFI/DFI_DK_X48T2RSB_Plus/results/fuzion/E8600_Q820A599_0464/crucial/ballistix/8500naked/9.5x/333_800/AFE_536-644_5559-A-A-pla_30-a_1212_trrd3trtp4_1.5875_104-2.525-1.665-1.39_66766761_800200_1244_AA/eeeea_eaaaa/spi32m_9m21s265ms_tn.png (http://fileshosts.com/intel/DFI/DFI_DK_X48T2RSB_Plus/results/fuzion/E8600_Q820A599_0464/crucial/ballistix/8500naked/9.5x/333_800/AFE_536-644_5559-A-A-pla_30-a_1212_trrd3trtp4_1.5875_104-2.525-1.665-1.39_66766761_800200_1244_AA/eeeea_eaaaa/spi32m_9m21s265ms.png)

http://fileshosts.com/intel/DFI/DFI_DK_X48T2RSB_Plus/results/fuzion/E8600_Q820A599_0464/crucial/ballistix/8500naked/9.5x/333_800/AFE_536-644_5559-A-A-pla_30-a_1212_trrd3trtp4_1.5875_104-2.525-1.665-1.39_66766761_800200_1244_AA/eeeea_eaaaa/everest.png

@5025Mhz - click image for full screenshot

http://fileshosts.com/intel/DFI/DFI_DK_X48T2RSB_Plus/results/fuzion/E8600_Q820A599_0464/crucial/ballistix/8500naked/9.5x/333_800/AFE_529-634_5559-A-A-pla_30-a_1212_trrd3trtp4_1.5875-2.525-1.665-1.39_66766761_800200_1244_AA/eeeea_eaaaa/spi32m_9m29s281ms_tn.png (http://fileshosts.com/intel/DFI/DFI_DK_X48T2RSB_Plus/results/fuzion/E8600_Q820A599_0464/crucial/ballistix/8500naked/9.5x/333_800/AFE_529-634_5559-A-A-pla_30-a_1212_trrd3trtp4_1.5875-2.525-1.665-1.39_66766761_800200_1244_AA/eeeea_eaaaa/spi32m_9m29s281ms.png)

System:

E8600 Q820A599 0464
CPU Cooling: Dtek Fuzion Rad Tower Box (http://i4memory.com/showthread.php?t=5133)
DFI LP DK X48-T2RBS Plus - 9/23 beta bios
128MB Gainward FX5200 PCI
2x1GB Crucial Ballistix PC2-8500 Tracer double sided Micron D9GMH dual channel kit
Memory cooling: 120x25mm Thermaltake 81cfm fan
750GB Samsung SATAII
Pioneer 215 DVD-RW
1200W Silverstone OP1200
WinXP Pro SP2 Nlite Fully Updated.

[flesheatinvirus]

Nice Pi score eva2000. One of my sticks of Ballistix just died so now Im on Teamgroup which is pretty good but you got me by a good 20secs. These E8600s scale rather well.

[CrystalAl]

excellent work:up::up:

[flesheatinvirus]

Some new Teamgroup timings at 5100mhz.:)

[MarcusFoX]

Nice setup...