E8400 (New Batch) 5.1G Enter Window at Low Volt 1.39V

[erickwok]

My new E8400 on hand

Just tested with Biostar P45 Board

please look at my video taken ..... go into window at 5.1G 1.39V
http://www.youtube.com/watch?v=0BOGrMGu-8M

[WhiteFireDragon]

that's great and all, but why didn't you just post a screen shot? that would have been much easier to read and quicker than a 5min video. i could barely verify any numbers in SPi 1M. good job booting at those clocks though...

[erickwok]

that's great and all, but why didn't you just post a screen shot? that would have been much easier to read and quicker than a 5min video. i could barely verify any numbers in SPi 1M. good job booting at those clocks though...



ok! now tidy up screen shot pictures
to be posted soon, WFD

[HDCHOPPER]

hard to read any of it for a 1 eyed biker lol
you need a louder fan :)

how about batch # too:D

[WhiteFireDragon]

and also test for highest stable clock with p95/orthos if you can

[VRSpy]

May I know the batch number ? :D

[erickwok]

May I know the batch number ? :D

Q832A

[Zeus]

Very impressive CPU, completey pwns my E8600. :clap:

[erickwok]

4g
4.5g
5g
5.04g
5.11g

capture screen pictures

[Ozzfest05]

im not impressed considering you were only using one core try using both cores and booting a 5ghz please enable both cores and show us what it can do

[erickwok]

E8400 at 5.11G faster than Core I7 4.53G (air cool)

[jaredpace]

why is your cpu-z and coretemp not reading the cpu-string correctly?

hrm

[Oliver]

there is some nice e84s e0 ya

jaredpace a disabled core gives the result u see

[HDCHOPPER]

that cpu is sweet !
did you get lucky or cherry pick it ?
thats all eye have been looking for is an air 5.0 cpu (at reasonable volts)

verry nice

[jaredpace]

jaredpace a disabled core gives the result u see

ah thanks! :D

[PytonOrm]

erickwok

E8400 at 5.11G faster than Core I7 4.53G you say ? =) well.
Then e8400 at 5.11ghz runs superpi at 9.156 sec and look at Core I7 4.53G you see 9.187 sec :rofl: explaing that mate ;) not faster than core i7 at 4,53ghz
Ownage mate !

[Zeus]

im not impressed considering you were only using one core try using both cores and booting a 5ghz please enable both cores and show us what it can do

I think in that video he was booting with 2 cores enabled unless he can disable one core in bios? I know Rampage Extreme has that option but does the Biostar have that option as well?


erickwok

E8400 at 5.11G faster than Core I7 4.53G you say ? =) well.
Then e8400 at 5.11ghz runs superpi at 9.156 sec and look at Core I7 4.53G you see 9.187 sec :rofl: explaing that mate ;) not faster than core i7 at 4,53ghz
Ownage mate !

Do you mean 9.156 is not faster than 9.187? :shrug:

[clockero]

Q832A

Please write complete batch - Q832A???

10x :)

[PytonOrm]

I think in that video he was booting with 2 cores enabled unless he can disable one core in bios? I know Rampage Extreme has that option but does the Biostar have that option as well?



Do you mean 9.156 is not faster than 9.187? :shrug:

dohh :ROTF:okey but he need over 5,11ghz to reach faster than core i7 at 4,53ghz

[RPGWiZaRD]

W T F ....

Crazy good E8400, beats any E8400 batch I've seen and maybe E8600 too for that matter even if single core mode is used.

[ADAM1337]

fpo ?
nice voltages , can u see photo with a multimeter ?

[VRSpy]

Q832a_ _ _ ;)

[erickwok]

Dear All

the batch no. is Q832A214

Good Luck To All!!!!
erickwok

[dinos22]

holy smokes man
that is a kick ass CPU

what's with all the haters in the thread :confused:

[Oliver]

holy smokes man
that is a kick ass CPU

what's with all the haters in the thread :confused:
ya and dont know seems quite crazy about all the haters

[erickwok]

ya, what problem with my single core test result??

[TheKarmakazi]

awesome work man!!! that beats my 8600... for 5G 1M stable I need 1.52v! One hell of a CPU u got there!

[WhiteFireDragon]

holy smokes man
that is a kick ass CPU

what's with all the haters in the thread :confused:

that's because they're jealous their chips can't come near those numbers :p:

good job on single core, but can you try testing it with lowest stable vcore for 5ghz using both cores?

[Duniek]

:eek:
4ghz @ 1,1V

please try to underclock it :D
maybe 0,7V @ 1,5-2ghz will be possible :D

[dinos22]

that's because they're jealous their chips can't come near those numbers :p:

good job on single core, but can you try testing it with lowest stable vcore for 5ghz using both cores?

meh i'm more jelous than them but i'm stunned
that frequency is amazing :D

what sort of ambients did you have :D

[runmc]

Nice chip erickwok :up: You've got a good one there. :clap:

[erickwok]

Nice chip erickwok :up: You've got a good one there. :clap:

thank you runmc

I will change X48 board to test in the forthcoming days;)

[clon22]

Holy.... :D
I need 1.61v to run my E85 for 1m...
very nice cpu eric!

[LagunaX]

Nice CPU there.
Does it do 1 hr stability at 4.5ghz?
A lot of chips can survive for 10 min orthos but crash at the 12, 14, 18 or 30 min mark for one reason or another...

[erickwok]

Holy.... :D
I need 1.61v to run my E85 for 1m...
very nice cpu eric!

thank you clon22

[dinos22]

oh thats interesting its a Q832B

[erickwok]

Nice CPU there.
Does it do 1 hr stability at 4.5ghz?
A lot of chips can survive for 10 min orthos but crash at the 12, 14, 18 or 30 min mark for one reason or another...

4.5G requires 1.25V-1.28V in Biostar P45(off course pass OR over 1hr)

[erickwok]

oh thats interesting its a Q832B

OH! it is

[erickwok]

I don't know what is the big difference between A and B?????

[LagunaX]

I just remove the heatsink and notice that is B not A

sorry to all

Q832B214 is the correct answer

Well enjoy your golden chip in Asia :).

Since it is a "B" chip we'll probably never see it in the USA - it's the same story all over again just like all of the super "B" e6600's that went to Asia and Europe but not to the USA...:down:

[erickwok]

Well enjoy your golden chip in Asia :).

Since it is a "B" chip we'll probably never see it in the USA - it's the same story all over again just like all of the super "B" e6600's that went to Asia and Europe but not to the USA...:down:

so sad!!!:(

[dinos22]

Well enjoy your golden chip in Asia :).

Since it is a "B" chip we'll probably never see it in the USA - it's the same story all over again just like all of the super "B" e6600's that went to Asia and Europe but not to the USA...:down:

oh stop crying :p::p::p::p::p:
you should see what sort of rubbish we get :rofl::D

[bluto]

Nice chip eric , I have eo 8400 also but don't know if it's any good so maybe i can also ask guys here . It's Q827A324 on dice.
http://img80.imageshack.us/img80/9235/839piet2.th.png (http://img80.imageshack.us/my.php?image=839piet2.png)

[erickwok]

Nice chip eric , I have eo 8400 also but don't know if it's any good so maybe i can also ask guys here . It's Q827A324 on dice.
http://img80.imageshack.us/img80/9235/839piet2.th.png (http://img80.imageshack.us/my.php?image=839piet2.png)

E8400 Q827A and Q826A also have good chips
as I saw some test results in taiwan before:up:

[dinos22]

Nice chip eric , I have eo 8400 also but don't know if it's any good so maybe i can also ask guys here . It's Q827A324 on dice.
http://img80.imageshack.us/img80/9235/839piet2.th.png (http://img80.imageshack.us/my.php?image=839piet2.png)

were you FSB limited
that looks weak for dice
nice vcore though....tried more?

[bluto]

Dfi dk t2rs+ is ok with high fsb but I chickened out of pumping more vcore, noob on subzero here. I'll keep trying.

[[XC] Oj101]

erickwok

E8400 at 5.11G faster than Core I7 4.53G you say ? =) well.
Then e8400 at 5.11ghz runs superpi at 9.156 sec and look at Core I7 4.53G you see 9.187 sec :rofl: explaing that mate ;) not faster than core i7 at 4,53ghz
Ownage mate !

Wow you really put your foot in it :rofl:

[kiwi]

I don't know what is the big difference between A and B?????

Bs have proven to be better clockers on average :)

[G H Z]

Nice chip :up:

[Pcuser]

Killer chip you have there man :up:

[bonzo_catalin]

My q827 , and that it is not max frecq i get , i do it only for fun .

And Spi1mb 5445mhz on SS .

http://www.hwbot.org/user.do?userId=5373

[C-N]

Sweet CPU erickwok look after it :up:

[erickwok]

that's because they're jealous their chips can't come near those numbers :p:

good job on single core, but can you try testing it with lowest stable vcore for 5ghz using both cores?


WFD

Vcore + 0.05V
i.e. 1.39V 5G Dual Core SPI 1M
& 1.44V 5.1G Dual Core SPI 1M

[junkmonk]

:clap:
i want one!!!!

so B's not coming to north america = assumption or truth?

and how can you tell from which week it is from the batch number?

[erickwok]

590x8.5=5G enter window no problem

[erickwok]

Air Cooling 5.18G 9.013s

next target ----> see 8s

[BiTsCrEaM]

:clap::clap:

And this is on a TP I45, right? I need one of these chips!

[erickwok]

:clap::clap:

And this is on a TP I45, right? I need one of these chips!

!!Bingo!!

[an0nym0us]

wow that's a very nice cpu.

[erickwok]

wow that's a very nice cpu.

Work it harder, Make it better, Do it faster, Makes me STRONGER :up:

[Zeus]

Erik, wanna trade yours for a 8600? :D

[CryptiK]

Wow really impressive cpu you got there.

[WhiteFireDragon]

Erik, wanna trade yours for a 8600? :D

he also has an e8600. i asked already asked :p:

[[XC] Oj101]

That thing's on drugs :shocked: Almost 5.2GHz on air!

[OC4/3]

Try strap tweak,should shave .0xx's off your SPI:D
BTW,you can get a 1M board to test if possible,this clock should be 8's something with the right board:shocked:
DFI LP DK P45 T2RS+ is good for 1M,so does Abit IP35 Pro
Anyway,dammmm nice chip there:clap:
Too bad 9x multi:(

[Zeus]

Try strap tweak,should shave .0xx's off your SPI:D
BTW,you can get a 1M board to test if possible,this clock should be 8's something with the right board:shocked:
DFI LP DK P45 T2RS+ is good for 1M,so does Abit IP35 Pro
Anyway,dammmm nice chip there:clap:
Too bad 9x multi:(


I wouldn't mind the 9x multi if it clocks like that, any decent board nowadays can do 600+FSB.

The DFI T2RS is a very good board for 1M indeed, with a non 45nm supporting bios that is. ;)

[HDCHOPPER]

erickwok your "B" is golden ....buy more of em :)

[Unseen]

I have here 3x q830A E0. Can you tell me what type of aircooling you are using? i tested only one for a couple of minutes and i can do 9x500@1,23-24v for bench.

Still on the crap box cooling.

[erickwok]

I have here 3x q830A E0. Can you tell me what type of aircooling you are using? i tested only one for a couple of minutes and i can do 9x500@1,23-24v for bench.

Still on the crap box cooling.

this one

http://www.thermalright.com/new_a_page/product_page/cpu/u120ex/product_cpu_cooler_u120ex.htm?art=MTQyMywxLCxoZW50 aHVzaWFzdA==

[erickwok]

never never over 1.45V for SP2004
too hot for 4.7G

[HDCHOPPER]

Air Cooling 5.18G 9.013s

next target ----> see 8s

should be eazy to do sub 9's for you

my ole co8400 did 9.838~9.746 iirc at 4.7
no tweeking just nice small drive 7200rpm 20gig & clean install
:up:

[erickwok]

should be eazy to do sub 9's for you

my ole co8400 did 9.838~9.746 iirc at 4.7
no tweeking just nice small drive 7200rpm 20gig & clean install
:up:

thank you for your advice HDCHOPPER:clap:

[bigwill68]

E8400 Q827A and Q826A also have good chips
as I saw some test results in taiwan before:up:

Hey erickwok good job on the Oc brother..I just pickup a E8400 EO Q832A
for $149.99 in the states.My question now is which numbers matter the most
the first 3 or the last 3 on the cpu to tell if you got a good chip to Oc with
Also see you got the BioStar TPower45 chip.. that I got on backorder at my
local Micro Center store here in the states good match..Ic they got the (B)
over there who got the (C):rofl: now..I gotta find the Memory your running
again great job:up: and the best of luck on your Rig:yepp:

[makaka]

Nice result men , But what the hell of noise this fan make , This look like a factory and no room :D:D:D (due to the noise)

[George_o/c]

erickwok, man with your cpu @ 5183, a DFi with pre-45nm bios and some nice 1M tweaking, one could pull off like 8.74x seconds :yepp:
Sick cpu ! :up:, do you want to trade with my E4300 ? :p: :D 3800MHz stable on air, 3950MHz max on air, 4464MHz max SPi 1M on dry ice ... :D

[RPGWiZaRD]

Can you test a quick 9x500 Orthos run? To see how much vcore is required? You're a lucky guy!

[heydo6]

very nice !!!

i would drop that bad boy on ebay and let the bidding begin .

[erickwok]

Hey erickwok good job on the Oc brother..I just pickup a E8400 EO Q832A
for $149.99 in the states.My question now is which numbers matter the most
the first 3 or the last 3 on the cpu to tell if you got a good chip to Oc with
Also see you got the BioStar TPower45 chip.. that I got on backorder at my
local Micro Center store here in the states good match..Ic they got the (B)
over there who got the (C):rofl: now..I gotta find the Memory your running
again great job:up: and the best of luck on your Rig:yepp:

Hi bigwill68

Awaiting your report on Q832A:up:

[erickwok]

erickwok, man with your cpu @ 5183, a DFi with pre-45nm bios and some nice 1M tweaking, one could pull off like 8.74x seconds :yepp:
Sick cpu ! :up:, do you want to trade with my E4300 ? :p: :D 3800MHz stable on air, 3950MHz max on air, 4464MHz max SPi 1M on dry ice ... :D


I prefer to trade with a good E8600 Q822A4xx:yepp:

[erickwok]

Can you test a quick 9x500 Orthos run? To see how much vcore is required? You're a lucky guy!

yes I will
post it for you :yepp:

[erickwok]

very nice !!!

i would drop that bad boy on ebay and let the bidding begin .

too many people got E8400
this chip not so special :D

[VOID WARRANTY]

i demand you to give me your golden E8400...RESISTANCE IS FUTILE.:D

[WaterFlex]

Just insane chip. I`d like to have the same one...

[bigwill68]

Hi bigwill68

Awaiting your report on Q832A:up:


My report will come sometime in December When..I get the rest on my stuff:yepp: Gotta save some Cash

[vservera]

nice chip vould like to see it on sub zero:)

[NapalmV5]

B + 1.2000vid = 5+ghz

not surprising at all :)

congratz on acquiring great chip :up:

[Hennels]

Well done :up:

What fan is that attached to your heatsink?

[CryptiK]

Any further results?

[Unseen]

A few results from my E0

Mobo: Biostar TPower I45
Ram: 2x1gb d9gmh
Psu: Silverstone Decathlon 1200w
Vga: 8600gt
Cooling: Aircooling - Thermalright Ultra 120

[namegt]

Q832A batch code
32pi TEST
http://cfs15.tistory.com/original/18/tistory/2008/11/22/21/32/4927fbf80cb41
http://cfs15.tistory.com/original/25/tistory/2008/11/16/10/47/491f7bc3e1204
cpu E8400
M/B DFI Lanparty UT P45 T2RS
RAM OCZ 7200 SLI 1x2
VGA x700
POWER ZM 750-HP

[makaka]

Those new E0 are killing me , most people get 5 Ghz with 1.4 or even lower under SS , I start to hate my chip (C0)which require 1.55v to be stable , u got a golden E8400

[Garrett]

I wonder what my new e8400 Q836A368 can do... ;)

[SiuL]

:eek:omg VERY NICE CPU

[d975xbx]

Q829A502...
http://photo.mofang.com.cn/photo/4111/7490/20081128003911170556.JPG

[bigwill68]

Hi bigwill68

Awaiting your report on Q832A:up:
Had it a 4.5 was'nt stable so gonna keep
it at 4.0 with low volts for right now
idling temps at 32c great:yepp:
I know it will do more not gonna
push just yet easy into it...down the line



screen shot of orthos (http://img380.imageshack.us/img380/3583/40andstayju7.jpg/)

Sandra Test
http://img386.imageshack.us/img386/5761/40sandratestxc8.jpg

Temps only got up to 53c under stress that's great in my book:)
next build will be water cooled for sure haf932

Oop's I almost forgot this test 2:)
http://img296.imageshack.us/img296/9882/intelburntestps0.jpg

[PhantomBeast]

Amazing...wish I could get one like that too...:p:

Just like to know more about the stability of the gold chip at 5GHz. Can this chip pass Prime 95 on small FFT, for at least 12 hours, erickwok?

Thank you very much for sharing it with us :clap:

[erickwok]

Amazing...wish I could get one like that too...:p:

Just like to know more about the stability of the gold chip at 5GHz. Can this chip pass Prime 95 on small FFT, for at least 12 hours, erickwok?

Thank you very much for sharing it with us :clap:

I am now waiting for a new Copper Thermalright Heatsink to break my air cool record.;)

http://www.thermalright.com/new_a_page/product_page/cpu/true-copper/product_cpu_cooler_t_copper.html

[C-N]

I am now waiting for a new Copper Thermalright Heatsink to break my air cool record.;)

http://www.thermalright.com/new_a_page/product_page/cpu/true-copper/product_cpu_cooler_t_copper.html

Nice, but did you check the weight...... ouch!!!

[NapalmV5]

Q829A502...
http://photo.mofang.com.cn/photo/4111/7490/20081128003911170556.JPG

no one noticed the foxconn avenger mobo ? :D

damn @ 1.125vid

[Mav451]

To the OP: I realize XS places an odd fascination with SuperPI, but is this overclock OCCT stable? 3D Stable (e.g. passes a couple hours of regular gaming use)?

[chris.y2k.r1]

Wow you really put your foot in it :rofl:

No :banana::banana::banana::banana:e! We now know to put exactly ZERO worth into any posts from this cat. Hell, super-basic math escapes him. He understands how to spend money though! Doh.

And pyth's follow up was, well, he needs to run faster than 5.11 to beat the 4.53 I7.... What!? He already beat it at 5.11... reality is hard to swallow sometimes - I guess... :ROTF:

[chris.y2k.r1]

To the OP: I realize XS places an odd fascination with SuperPI, but is this overclock OCCT stable? 3D Stable (e.g. passes a couple hours of regular gaming use)?

I run both, but I find that OCCT is not as hard as SPI is on overclocks. I can run the latest OCCT for hours (Rev 2.1 I think??) but if my settings aren't perfect, I'll crash SPI in 3 minutes. It's no 'fascination', SPI, especially 32M, is the last word in stability IMHO - aside from gaming. Gaming is the end all be all for stability as I can be ALL stress tests stable and still crash games. That's because the northbridge and video cards aren't pushed with any other stress tests. I wish there was an OCCT with video stress test. That would be the way to go.

--- End Hijack.

[kenofstephen]

I smell a lot of jealousy.

[erickwok]

I believe most extreme overclockers here are seeking for extreme speed and not for extreme stable
those haters on overclocker's superpi second why not challenge on CPUZ's capture screen....?? no meaning in this extreme site
why not just keep the mouth open if can't keep the mouth shut??

[George_o/c]

I run both, but I find that OCCT is not as hard as SPI is on overclocks. I can run the latest OCCT for hours (Rev 2.1 I think??) but if my settings aren't perfect, I'll crash SPI in 3 minutes. It's no 'fascination', SPI, especially 32M, is the last word in stability IMHO - aside from gaming. Gaming is the end all be all for stability as I can be ALL stress tests stable and still crash games. That's because the northbridge and video cards aren't pushed with any other stress tests. I wish there was an OCCT with video stress test. That would be the way to go.

It has been stated, like a billion times ... this is Xtremesytems, that's the way we like to overclock, pushing the system to its limits ... knowing that the system is 32M stable, is enough for us, because we know that now we can bench some 3Ds with no problems at all :)

Screw stability ffs :down:, this is www.xtremesystems.org :yepp:

[rockfella]

Simply rocking!!!! 5 ghz possible on air now!!

[Glow9]

Anywhere stateside to find these?

[MarcusFoX]

very sweet gotta getme a low vid one of these

[mikesrex]

Do you mean 9.156 is not faster than 9.187? :shrug:

with times that close, it's all about who has the quickest reaction time at the tree