Asus P5Q - cheap and good clocker

[PcCI2iminal]

http://img240.imageshack.us/img240/1092/016nh6.jpg
http://img75.imageshack.us/img75/5732/007lf9.jpg
http://img75.imageshack.us/img75/4555/010bk8.jpg
http://img240.imageshack.us/img240/2645/012bd7.jpg
http://img240.imageshack.us/img240/5363/021do8.jpg


old school jumper
ov cpu - up to 2.10v
ov nb - up to 2.26
other voltages
cpu pll @ 2.78v
fsb voltage @ 1.9v
vdimm @ 3.08v
sb voltage @ 1.4v
pcie sata voltage @ 1.8v
load-line calibration - works great

http://img240.imageshack.us/img240/8567/imagemux7.jpg

vcore @ 1.3v
vdimm @ 2.1v
and minimum settings for all
cpu cooler -> Scythe Infinity + 120mm @ 102CFM
room temp - 28c

fsb 560MHz
http://valid.x86-secret.com/show_oc.php?id=374922

cpu pll @ 1.7v
fsb voltage @ 1.3v
vdimm @ 2.38v
nb voltage @ 1.4v
sb voltage @ 1.2v
pcie sata voltage @ auto


i can place my modules in any slot but i can not use a pair on dual channel ,the dual channel seems to be dead :(

[eva2000]

nice fsb.. but no dual channel :eek: :(

what voltages used for 560FSB ?

[@rne]

Interesting. Do you have troubles getting over 560?

[PcCI2iminal]

nice fsb.. but no dual channel :eek: :(

what voltages used for 560FSB ?

check again George :D ,no dual channel but is a very funny board and i will test a bit more before i send it back




Interesting. Do you have troubles getting over 560?


i still trying :)

[eva2000]

oh there they are... cpu pll = 1.7v :eek:

[PcCI2iminal]

oh there they are... cpu pll = 1.7v :eek:

it starts at 1.5v (~2.78v) :)

[Hyperhorn]

Dual Channel does not work? Should be fixed... :D
Even if 560 Mhz is the max this is enough for the most non-extreme OCer/ gamers out there with a small budget.

[eva2000]

maybe that's why fsb is high due to single channel ?

[Richard Dower]

Wonderful high res pics, thanks thanks.

[scooter.jay]

All the new P45's are looking good.:D

[Eldonko]

Nice photos although I have to scroll to see em. Looks like a nice budget board, hopefully you solve dual channel issue.

[Morais]

Imma little worried now...just bought this mobo with a 2x2GB Gskill DDR2 1000 kit :stick:...I hope asus fix it until I receive mine

[Nasgul]

Dual Channel does not work? Should be fixed... :D
Even if 560 Mhz is the max this is enough for the most non-extreme OCer/ gamers out there with a small budget.

Look closely.......only using SLOT 1, which means only ONE memory module was used.

Now! If he were to use TWO memory modules, then SLOT 1 and then SLOT 2 would be used and thus "Dual Channel" would be born, like this: http://valid.x86-secret.com/show_oc?id=163560

__________________________________________________ _-

I'm not impressed.........all ASUS boards are bad ass.........born to be that way.

[Shadowthor]

+1, He is running only one memory module.

[Morais]

Bought the mobo with 2x2GB Gskill pc8000 kit and working fine out of the box.I hope you dont have problems with it :up:

[ThugsRook]

mine does pretty well in dual channel mode :shrug:


500fsb is completly stable.

still working on 533fsb...
http://i224.photobucket.com/albums/dd164/ThugsRook/P5Q/spi1m-533.jpg


max CPU-Z is 550fsb so far...
http://i224.photobucket.com/albums/dd164/ThugsRook/P5Q/cpuz-550.jpg

[Flip_Lx]

good to see the "low end" P5Q clocks nicely, almost making me wish i bought an e8*00 instead of a quad to get some crazy FSB numbers but the biggest thing i have against this board is where they placed the 24pin power....

(ok sorry for derail very nice numbers folks PCc12iminal and ThugsRook)

[Spitphire]

For some reason CPU-Z reports that I'm running DDR3 with this board when I'm running DDR2 800.

[Morais]

Thats fine.Even the latest everest dont recognize the motherboard correctly .

[janolle]

I have a very frustrating problem: I can do prime stable 4000mhz on both small and large fft's and play games and benchmarks. The wierd thing is that i get random lockups and reboots that are not repeatable. On thing is for sure: it doesn't happen when idle or with 100% cpu load. One thing i know for sure is that it's FSB related since it starts to happen at anything higher than 423FSB on any multiplier.

I'm not sure if it's my P5Q or something else. I've tried everything I can think of: voltages, mem dividers and all the wierd settings in the BIOS.
I'm currently stable at 3807mhz (9x423mhz) with the followin settings.

1.16vcore (prime95, have to set 1.20v in bios with LLC disabled)
1.52vPLL
1.12vFSB
1.12vNB
1.98vDIMM (memtest86+ error free at 1060mhz so that's not a problem)

3800mhz is stable at very low voltages so it would be nice to see what this little E8400 is capable of. :(

I really hope that someone had and solved this problem. It's very frustrating to do stability testing with no prime95 errors, the bastard just freezes or reboots.

[ThugsRook]

I'm currently stable at 3807mhz (9x423mhz) with the followin settings.

1.16vcore (prime95, have to set 1.20v in bios with LLC disabled)
1.52vPLL
1.12vFSB
1.12vNB
1.98vDIMM (memtest86+ error free at 1060mhz so that's not a problem)

3800mhz is stable at very low voltages so it would be nice to see what this little E8400 is capable of. :(

I really hope that someone had and solved this problem. It's very frustrating to do stability testing with no prime95 errors, the bastard just freezes or reboots.
try...
1.14vFSB
1.14vNB

[Vivi]

damn i had trouble with this board.. it totally sucked for me

at 1:1 its almost impossible to get 8 pl, i dont even think i got 8pl, + 560fsb was my max stable and around 565 validated, but i hated that board..

Why is there a 2.2v NB jumper anyway.. p45 locks up on high volts .

[ThugsRook]

damn i had trouble with this board.. it totally sucked for me

at 1:1 its almost impossible to get 8 pl, i dont even think i got 8pl, + 560fsb was my max stable and around 565 validated, but i hated that board..

Why is there a 2.2v NB jumper anyway.. p45 locks up on high volts.
Asus did a real chit job on all these P5Q-X boards/bios'.

dispite the fact i can run 500fsb 100% stable, i still hate this board cause its so completely uncooperative.

[Glow9]

In the first pic the power slot at the top how come it has 4 covered up? Doesn't need that much power?

[N00B]

´Great Board :up:

I just don't understand why the hell is the 24 pin atx connector is on the wrong side.

[janolle]

I found a problem that might be the solution to my FSB problems: even at 1.16vNB my NB is so hot that the heatsink on it burns my fingers.
Added a 120mm (the bigger the better, hahaa) fan and testing if it helps, atleast the heatsink on it feels alot cooler now. Crossing my fingers, running orthos and waiting for my paycheck so that I can buy some proper cooling on that bastard.

[RunawayPrisoner]

Hmm... clocking a E7200 with this is a whole lot of trouble for me. Just can't get more than 475MHz FSB no matter what (maxed out voltage? Not even at x6 multiplier), and Grub wasn't compatible with the BIOS or something... so... a full reinstall had to be done for Windows. :(

Worse yet... not even a BIOS flash fixed anything.

Dual-channel memory works, but not sure how well. May do a benchmark later.

And before you say it's a RAM issue, the RAM sticks can be clocked to 590MHz just fine. Just not with 1:1 ratio, and not with this E7200. Will throw in a Q9450 next to see if it's a board issue, or a CPU issue. Leaning towards board, since the E7200 could be clocked to 4.5GHz on an ASUS P5E-VM HDMI board.

[janolle]

Do you get unexplainable lockups at higher FSB settings? Or just errors in Orthos?

[Morais]

Has anyone tried the new 1004 bios for this mobo?

[RunawayPrisoner]

Do you get unexplainable lockups at higher FSB settings? Or just errors in Orthos?

Not even booting at past 450.

[ThugsRook]

Has anyone tried the new 1004 bios for this mobo?
yea i use v1004, its the best one so far IMO.

[hema]

I flashed to 1004 with one problem
my q6600 cpu temp. show in bios and with real temp in windows lower than the last bios version 703 with 10 degree
this wrong reading in temp with this bios version and Q6600 processor why?
so I reflashing back to 703

[ThugsRook]

I flashed to 1004 with one problem
my q6600 cpu temp. show in bios and with real temp in windows lower than the last bios version 703 with 10 degree
this wrong reading in temp with this bios version and Q6600 processor why?
so I reflashing back to 703
please explain to me how you know which one is wrong?
or if any of them is right?

[janolle]

This board is wierd: I have to run at PL8 for stability on over 400mhz fsb.Anything higher will hard crash eventually and anything lower just won't boot. This happens with bios version 1102, is the 1004 a later version?

[ProStreetCamaro]

Avoid 1004 at all costs. With the new bios I can not get back to 4.0 on my E8400 no matter what I try. On 703 I could easily do 4.3 on air. My 24/7 was 4.0 at 1.33 volts. Now 4.0 is a no go. I am tired so i will flash back tomorrow.

[philbrown23]

so glad I changed my mind about sticking to asus with my P45 board. gonna either get biostar or gigabyte, leaning towards gigabyte.

[ThugsRook]

Avoid 1004 at all costs. With the new bios I can not get back to 4.0 on my E8400 no matter what I try. On 703 I could easily do 4.3 on air. My 24/7 was 4.0 at 1.33 volts. Now 4.0 is a no go. I am tired so i will flash back tomorrow.
dont give up so fast. 1004 is very different from 703 and may require slightly different settings and voltages.

if using nbs400 before try nbs333 now, or vise verse.
cpu management: optimum ...seems to get me the highest fsb

etc

HTH :)

[ProStreetCamaro]

dont give up so fast. 1004 is very different from 703 and may require slightly different settings and voltages.

if using nbs400 before try nbs333 now, or vise verse.
cpu management: optimum ...seems to get me the highest fsb

etc

HTH :)



Thanks for the tips I will give it a shot when i get home from work. :D

[RunawayPrisoner]

Okay... never mind. Threw a Q9450 in, and booted right into 495MHz (495 x 8. Approx. 3.80GHz or so). Guess the BIOS just couldn't handle E7200.

By the way, BIOS is 0506.

Update: Q9450 3.20GHz (400 x 8) at 1.12v stable...

[Leeghoofd]

so glad I changed my mind about sticking to asus with my P45 board. gonna either get biostar or gigabyte, leaning towards gigabyte.

How can you compare a budget board like the P5Q with the P45 DQ6 you are getting... total different ballpark here... will be interesting to see ya test on that board and compare it with the E or Dlx version...

Total useless post to me....:confused:

[ThugsRook]

im not seeing the plain P5Q doing any better or worse than any of the other P45 boards. for a so called "budget board" it holds its own quite well. the only thing budget about the P5Q is the 1x PCI-E.

yes the bios is a complete PITA, but it does run.

[ProStreetCamaro]

How can you compare a budget board like the P5Q with the P45 DQ6 you are getting... total different ballpark here... will be interesting to see ya test on that board and compare it with the E or Dlx version...

Total useless post to me....:confused:


I agree. The P5Q is simply a great board for the price. My system runs my E8400 at 4.3 stable with a little more vcore. I dont see it doing any better on any other board.

Here is 4.0 on the P5Q. This litteraly took nothing to acheive. 3rd boot ever on this chip and board get me 4.0.

http://img.photobucket.com/albums/v426/prostreetcamaro/bench.jpg

[Morais]

New Asus P5Q BIOS: 1104 (http://dlcdnet.asus.com/pub/ASUS/mb/socket775/P5Q/P5Q-ASUS-1104.zip)

[MajkY]

One thing i cannt find out clearly... Does this board obtain Raid support ? what SB IHC10R ?

[Ket]

+1 for a fantastic board from Asus. Can't say I like the plain P5Q much, but from the Pro onwards look up and the sky is the limit :)

[Venom-Crusher]

Please tell me It has OV_nb jumper or not?

[ThugsRook]

Please tell me It has OV_nb jumper or not?
yes, OV_NB and OV_CPU jumpers are on the board.

[Mask]

can someone tell where P5Q vcore measure point?

E: soon will buy E8500 and will see what max fsb on this board :)

[hema]

any one try 1406 bios version
any feedback