best super pi times?

[Tom Holck]

Yeap,

M32 is almost action for me now.

right down the figure, zip the wine, look at the clock (sek)
and.... new figure...
wait a few sekunds
right down the figure, zip the wine, look at the clock (sek)
and.... new figure...

In the background I hear the 2 big compressors working hard
to pump the R1150a
looking at the ice formation om the M/B. checking the volt
checking the temp ... etc



very exiting :banana:

[Learn]

damn good :D

congrats Tom Holck

[bigZ]

I got my superpi 1m time down to 38s, need more vDIMM and vDD along with non-stock cooling on the northy if I'm gonna get anything better than this. I reckon 11x236 will get me 37s if the scaling works correctly.

12.0 x 216 = 39s
11.5 x 226 = 38s
11.0 x 236 = ??s

http://www.enscape.net/bigz/GCS0002.jpg

No matter what vCore above 2.2v I set, it freezes either in windows or on boot. I think the mosfets or vregs aren't upto it though cause it only reads 2.15v idle, 2.09v load.

not bad for a silent pc with a cooling setup that's not designed to perform :) (3/8" OD tubing)

[some_young_guy]

Hi Tom. Was your benchmark run on Windows 2003 64-bit server? And would you get a worse or better run on any other 32-bit windows version?

[Dane]

http://digilander.libero.it/daneviz/barton%202500/35b.JPG

vcore = 2.25v by bios, cooled by prommy :stick:
timings was 11222 if I remember well :confused: :p:

[Tom Holck]

Originally posted by some_young_guy
Hi Tom. Was your benchmark run on Windows 2003 64-bit server? And would you get a worse or better run on any other 32-bit windows version?

Yes, the M32 was on win 2003 server AMD 64 bit. A little worse results on 2003 32 bit or XP or win2000. On the other hand can I go a little faster (3151mhz) on 32 bit in M32 ? My old record was
3133 Mhz in win-xp it was 26.26 same timings etc.
It seems like the 64 bit runs a lot hotter, but its fast in M32 as you can see.
In Pifast, M8 etc is XP the fastes for now. When properly set up, 2003 32 bit might be faster her.:toast:

[cpulloverclock]

Originally posted by Tom Holck
Yes, the M32 was on win 2003 server AMD 64 bit. I little worse results on 2003 32 bit or XP or win2000. On the other hand can I go a little faster (3151mhz) on 32 bit in M32 ? My old record was
3133 Mhz in win-xp it was 26.26 same timings etc.
It seems like the 64 bit runs a lot hotter, but its fast in M32 as you can see.
In Pifast, M8 etc is XP the fastes for now. When properly set up, 2003 32 bit might be faster her.:toast: and the 1M digits?
always 25-26s?


Try a 10M PIFAST please
:stick:

[cpulloverclock]

ouch
that's incredible :eek:

268 1:1 in dual mode with a FX-51
5'52@2543MHz!!! awesome
http://www012.upp.so-net.ne.jp/ohij2/838-552.gif

and :slobber: :slobber: :slobber: :slobber: :slobber: :slobber:

http://www012.upp.so-net.ne.jp/ohij2/330.gif

[bias_hjorth]

ohh my §§§§ing god...

thats gotta be a wold record in mem speed..

[cpulloverclock]

Originally posted by bias_hjorth
ohh my §§§§ing god...

thats gotta be a wold record in mem speed.. for an ECC module

[bias_hjorth]

Originally posted by cpulloverclock
for an ECC module


yeah my point exactly :-)
what are those-- corsair?

[cpulloverclock]

Originally posted by bias_hjorth
yeah my point exactly :-)
what are those-- corsair? sorry but I dont know
:(

wait a minute, I look at something



M/B Asus SK8N(nForce3 Pro 150,modified by Dr.ƒXƒ‰ƒ“ƒv)
CPU Athlon64 FX-51
Infineon PC3200 BT-5(Type W=CH-5?) 512MB(Reg/ECC)x2

[FUGGER]

I finally got some superpi runs last night

29 seconds at 4.6Ghz

I wish superpi gave a little more accurate times in the tenths of a second.

I will upload when I fire up that hard drive.

[Tom Holck]

Originally posted by MickeyMouse
tom what temps show in the bios and under load on die temp's??

-47 C

What have you seen ?

[FUGGER]

12 seconds on the G5

against dry ice and a 64 bit chip, im not doing so bad =)

[Tom Holck]

Originally posted by MickeyMouse

dryice+acetone
3400+@1.9v@2.925ghz
-38c bios
-21c load
thru 32m superpi 26s< [/B]

If I run M32 at lets say 3152 at 2.112 volt for 15 min it stops.
If I reboot fast, then I see -32c in bios. In about 1 min it is back to -46/-47c . But it's only in 64 bit OS. In 32 bit 3152 Mhz +2 volt no temp drop.
konklusion -21/-38c is not sufficient:rolleyes:
Charlie had also dissapointments with FX and dryice.

[Tom Holck]

Originally posted by FUGGER
12 seconds on the G5

against dry ice and a 64 bit chip, im not doing so bad =)

Hi FUGGER

nice you are back with some nice cooling

? 12 sek on what:confused:

[FUGGER]

Apple G5 can do pi to the millionth place in a little over 12 seconds @ 2.0Ghz

I have a G5 project comming up for 2.6Ghz on phase change.

[Tom Holck]

Originally posted by MickeyMouse
G5=apple I thinks :)


what compared to you?? I didnt understandd what ya meant?:confused:

My dryice container unlike charlies has alot more mass at the base like 4x's as much also I get dryice pelets so alot more surface area.. when I put the setup back on line Ill upload the MBM5 scrren high/low after the 32m run never did it drop below
-21c load not the best cooling, but it walks all over the mach II stock I have here. :) maybe Ill do LN2 one day soon.

I meant that going higher than -32 is clearly to high for 31xxMhz /64 bit speed on the FX. Then dryice cooling is not sufficient for proper cooling at that speed. We must use something better to go on. Costum Cascade, LN2 etc.

BTW agree with you March II stock is not for FX, it's to hot:p:
Nice you still are here, read something in "speak freely"
:toast:

[cpulloverclock]

the best link : http://holicho.lib.net/pi3355/pi3355.htm

:toast:

Tom, I hope u'll be the first guy to break 5 min on the 8M digits of SuperPi with Win2k3 Server 64-Bit :)

[macci]

Apple G5 can do pi to the millionth place in a little over 12 seconds @ 2.0Ghz
But you are using different calculation program there right? So it cannot be compared at all.
I remember seeing certain PiFast version do 1M at less than 10sec with ~4G P4.

29sec at 4.6G? That seems a bit slow. I was able to go just below 30 at 4.41G. 4519MHz gave 28sec and 4650 would have been 27 - I only got to 4648 which gave the same 28 sec I got at 4519 already.

[FUGGER]

P4C800 Deluxe Rev2 16x289 5:4 2-2-2-5 on the 29 sec run. I should have done more shutting down of processes. I found out later Turbo was off.

mem and stab modded

original bios 1101 or 1011. new board, was testing the high end.

[Kunaak]

my little stab at it.

[Learn]

very nice Kunaak :slobber: :D
it's prommy cooled?

[Redskin]

Here my baby ...

Barton @2.59 gig :D not so fast like Kunaak but it's only a Barton
http://mitglied.lycos.de/martinteichmann/super_pi_38sec_2.jpg

[Kunaak]

Originally posted by Learn
very nice Kunaak :slobber: :D
it's prommy cooled?

my particular benchmark was done with dry ice.
not much else, besides a Vdimm and VDD mod.

:D

[Bravo]

http://bravo.ausgamers.com/a64/3200/36seconds-2373.jpg

36 seconds @ 2.5-4-4-9 @ 2373 (10x 237mhz FSB 1:1 @ 1.65v).

[xsky]

31s (http://maitre.physik.uni-kl.de/~mkrauss)

with A64 2,71GHz (VapoXE) and 2*256MB KHX3200 @ 271 2-2-2-5

[SAE]

Mine at 11x260 11-2-2-2-2,0-13-16 :)

[shidokanjohn]

Mine after taking mobo from Hipro5 (thanks my friend), changing cpu and gas at promie:D

[CodeRed]

Here's my A64 effort

http://users.tpg.com.au/spark69/an50r/superpi31.jpg



Just scraped in under 31 sec ;)

[hipro5]

Talking about Super-Pi...here's my newest one......

[cpulloverclock]

with my 3.4C vapo chilled

http://membres.lycos.fr/cpulloverclock79/1Mo..jpg
http://membres.lycos.fr/cpulloverclock79/2Mo.JPG
http://membres.lycos.fr/cpulloverclock79/4Mo.JPG
http://membres.lycos.fr/cpulloverclock79/8Mo.JPG
http://membres.lycos.fr/cpulloverclock79/16Mo.JPG
http://membres.lycos.fr/cpulloverclock79/32Mo.JPG

[IamAnoobieCheez]

that is one hell of job, cpulloverclock.



here's my M-barton 2400+@ 2.88ghz @ 250 fsb..

34 sec.

[SAE]

@ cpulloverclock:

:confused: Your rails in sig are a joke, aren't they? :D

[nailbomb]

2.8C at 14x250 5:4 mem:

41 seconds.

[Hoschi]

FX51 ->Mach1,, 2x Corsair PC400 ECC Reg. LL,, SK8N...

http://www.dark-tweaker.com/yabbse/attachments/pi_1M.jpg

Hoschi :D

[cpulloverclock]

Originally posted by SAE
@ cpulloverclock:

:confused: Your rails in sig are a joke, aren't they? :D No, that's real ;)

[SAE]

@Hoschi.

Congrats my man. Landsmann :D

Nice results. Expensive rig, isn't it ;) ?

[ultron5]

Haven't postet it yet, here's my ol 2.4C on chilled Water -10°C ;)

http://mitglied.lycos.de/coolinglimit/Hardwarepics/SL6Z3/SuperPI_324.png

[ultron5]

Originally posted by cpulloverclock
with my 3.4C vapo chilled


really impressive dude!!! :slobber: :D

What temps do u have? Is that only a small Vapo ?? unbeleavable i think u're joking! :p:

[SAE]

@ultron5

Nice ram oc on your p4 :D (with superb timings)

I assume it's at least a vapo pe if not xe that cpulloverclock is using :)

P.S. Welcome to the sickness ;)

[[_Silence_]]

Finnaly got 32 seconds:D

A64 3000+ @ 2920Mhzs Mushkin Level II DDR 487Mhzs

http://pwp.netcabo.pt/orlandojdr/32s.jpg

[Iridium192_217]

why is it that p4's seem to do better in this test?

[[_Silence_]]

Originally posted by Iridium192_217
why is it that p4's seem to do better in this test?

Because it has Dual Channel, and mems are very important for SuperPI.
Look at the FX-51 scores, they're better than the P4 ones.

[bias_hjorth]

Originally posted by Iridium192_217
why is it that p4's seem to do better in this test?


you´re wrong their buddy..

Remember you have to compare the right cpu´s - amd64 vs. p4 and the P4ee vs. FX..
in both AMD is ahead :)

[LikwidKool]

damn I need better cooling. I can do 240fsb but the superpi time doesn't change.

Here's my 37sec at 3759.

[Learn]

new cooling :)

http://learn.chez.tiscali.fr/34s-DOD-R22.png

[Learn]

new cpu :)

need some tweak
DOD R22
http://membres.lycos.fr/ftpad/images/3.0C/superpi1M.png

[IamAnoobieCheez]

Très bon!!, mon ami. :up:

[Learn]

Thanks :) merci

[EmineM]

MY A64 3400+
Unmodded Mach II and with heatspreader ontop

[kommando]

Who has the fastest 2500+?

[cpulloverclock]

Originally posted by kommando
Who has the fastest 2500+? I've ever seen a 2500+ not mobile at 3030MHz with a prometeia
http://members.lycos.nl/neutebeut/smilies/slaap/slapen001.gif

[SAE]

Yeah. Most times the fsb is so low that it does not matter if 3gig with 200 to 215fsb or 2,8gig with 255 ;) (high fsb is the winner most of the time)

Believe me, I know... :(

Holst had (or still has) a barton doing 3gig but no high fsb for him as well... May the board or the cpu set the limits.

[kommando]

I was referring to the fastest super pi time...

[SAE]

And that's what I meant... no hgih fsb, no high benches :rolleyes:

I think nobody with an xp (barton etc) has broken 34s (read this thread and you will see) me as well...

Needs high fsb and over 2,9GHz.

[cpulloverclock]

Originally posted by kommando
I was referring to the fastest super pi time... ok
I dont know, 33s?

[bias_hjorth]

Originally posted by SAE


I think nobody with an xp (barton etc) has broken 34s (read this thread and you will see) me as well...




Sure there is. But not with a xp2500 - I believe the record barton was MEMESAN running a XP2800 around 3464 and 231fsb.. That gave a SUPERPI at 31sec..:eek:

[SAE]

Originally posted by bias_hjorth
Sure there is. But not with a xp2500 - I believe the record barton was MEMESAN running a XP2800 around 3464 and 231fsb.. That gave a SUPERPI at 31sec..:eek:

Okay. But not with 24/7 cooling ;)

LN2 I assume :slobber:

/edit: Mine was a locked 2500+ week49...

[bias_hjorth]

No not 24/7

but with ‰t‘Ì’‚‘f—â‹p cooling (I assume thats LN2) :D
screenshot;

http://members.jcom.home.ne.jp/3233730401/WS000049.JPG

[SAE]

Originally posted by bias_hjorth
No not 24/7

but with ‰t‘Ì’‚‘f—â‹p cooling (I assume thats LN2) :D


LMAO :rotf:

[ultron5]

Originally posted by bias_hjorth

http://members.jcom.home.ne.jp/3233730401/WS000049.JPG

REALLY amazing !!! The most ingenious is the fact that this Bench is made in mid 2003, and even high OCed Northwoods have problems to beat this score. :D

[bias_hjorth]

Yup thats the most impressive part of it.. Actually I had a almost 100% similar stepping on my old xp2800 that did 2610mhz (around mid 03) with water or the same using a sucky vapo and only 1.8 vcore :)

[Stang_Man]

36s @ 2912MHz, XP2400-M

:)


i'd like to know, does Super Pi take advantage more of CPU or FSB??

[bias_hjorth]

I would say 1:1 fsb action over cpu..

[SAE]

Originally posted by Stang_Man
36s @ 2912MHz, XP2400-M

:)


i'd like to know, does Super Pi take advantage more of CPU or FSB??

Yep.

11x260 gave me 34s ;)

[SAE]

watch. older bench with locked barton 2500 :thumbsup:

[Learn]

Originally posted by SAE
watch. older bench with locked barton 2500 :thumbsup:

nice
and pretty near 33s...

[SAE]

Yeah.

Unfortunately I could not get an additonal mhz on the fsb with this board... I hope I can improve the time when my LP B replacement gets here :) (bench is nearly 2 months old)

[bias_hjorth]

hell of a job btw.!! :toast: .. Arent you no 1. on the orb with a barton or does bowman record still stands?

[dpa]

my best score:

http://www.home.no/dpa/Ftp/Bilder/vr-zone.JPG

i get the same score at 4140mhz.. so iam pretty close to 32sek i think.. 30-40mhz more maybe..

[TinTin]

32sec. A64 3200+ @276.7*10

[Zeus]

Very nice oc/score TinTin. :thumbsup:

Just watercooled?

[TinTin]

Originally posted by Zeus
Very nice oc/score TinTin. :thumbsup:

Just watercooled?

Just changed to MACH II cooling. For watercooling, it was at about 2500MHz.

My photo in signature not yet changed. :p:

[Stang_Man]

Originally posted by bias_hjorth
hell of a job btw.!! :toast: .. Arent you no 1. on the orb with a barton or does bowman record still stands?

#1 is LORD with a 9800 PRO!!!

[SAE]

Originally posted by bias_hjorth
hell of a job btw.!! :toast: .. Arent you no 1. on the orb with a barton or does bowman record still stands?

Thanks. Worked hard for it ;)

Don't know about no 1 :confused:
All I know is Bowman was taking his 24k apart cause nature was too high... error in 3dm (I also have two benches over 24k with impressive nature scores..24,1k :D )

What's LORD's score???

[Stang_Man]

Originally posted by SAE
What's LORD's score???

like 24,3 or so

[SAE]

Originally posted by Stang_Man
like 24,3 or so

It's all about graphics clocks... and my radeon is lame :mad: (only at 500-760 or so)

[WildKard]

36 seconds on my 3.0C @ 3824 (no it doesnt take 1.75v thats actually 1.625v and my asus goes mental with overvolting at idle heh)

[cpulloverclock]

cache L1 and L2 disabled

It's worse than my 30s with the 3.4C :D

http://membres.lycos.fr/cpulloverclock79/low1m.JPG
http://membres.lycos.fr/cpulloverclock79/lowcpumark..JPG

[caater]

a lil 1M test.
486-sx33
20M ram

http://pillemati.cafe.ee/~kalle/pents/486_superpi.jpg

[niaboc79]

http://www.yamafoto.com/users/niaboc79/hr/13916/280-2-2-2-5.JPG

I think i can do 29s

[paul007]

1:1 at 280mhz 280x10 at 2-2-2-5 and your only running 26.5k in 2k1???

time to bench again and so some 27.5k action :)

nice score niaboc

[niaboc79]

Originally posted by paul007
1:1 at 280mhz 280x10 at 2-2-2-5 and your only running 26.5k in 2k1???

time to bench again and so some 27.5k action :)

nice score niaboc

my score in 3d are still in watercooling, not yet with my mach 2

;)

[paul007]

;) NICE :) Im so jelouis that is the lowest cpu freq. superpi 1m I have ever seen maybe lowest ever.. what ram??

[IamAnoobieCheez]

Very impressive... niaboc79 :toast:

[Try-this]

I just did superpi 1M on an old dual computer; ASUS P2B-D+2*266 mhz pentium II , it got 7minutes and 33seconds - strange thing is that with only one processor in it, it also gives 7minutes and 33seconds...

Can superpi not use the power of 2 cpus?

[niaboc79]

Originally posted by paul007
;) NICE :) Im so jelouis that is the lowest cpu freq. superpi 1m I have ever seen maybe lowest ever.. what ram??

corsair PC3200LL BH5

[Learn]

Originally posted by Try-this
I just did superpi 1M on an old dual computer; ASUS P2B-D+2*266 mhz pentium II , it got 7minutes and 33seconds - strange thing is that with only one processor in it, it also gives 7minutes and 33seconds...

Can superpi not use the power of 2 cpus?

only one cpu.

niaboc
not bad......:D

[Try-this]

Originally posted by Learn
only one cpu.

ok...

thanks :)

[nailbomb]

This is my new box, on air: MCX478-V/Tornado.

LanParty PRO875B
2.8C MO
2x512 OCZ GOLD 4000EL 1:1

[macci]

Remember you have to compare the right cpu´s - amd64 vs. p4 and the P4ee vs. FX..
in both AMD is ahead
as far as the world records go..

P4EE record is at 24sec (5269MHz)
FX-51 is at 26sec (3304MHz)

P4E 2.4A record is 27sec (4736MHz)
A64 3400 record is 27sec (3174MHz)

all ln2 cooled

[Zeus]

My best so far, aircooled:

[macci]

Prescott 2.4A:

34sec @ 3801MHz (211x18) (http://www.akiba-pc.com/e107_images/articles/24a/34sec_3801mhz.gif)

33sec @ 3962MHz (220x18) (http://www.akiba-pc.com/e107_images/articles/24a/33sec_3962.gif)

32sec @ 4038MHz (224x18) (http://www.akiba-pc.com/e107_images/articles/24a/32sec_4038.gif)

31sec @ 4166MHz (231x18) (http://www.akiba-pc.com/e107_images/articles/24a/31sec_4166.gif)

30sec @ 4317MHz (240x18) (http://www.akiba-pc.com/e107_images/articles/24a/4317_spi1m_30s.gif)

almost 29sec at this speed :D
http://www.akiba-pc.com/e107_images/articles/24a/4413_spi1m.gif

[paul007]

nice macci but the other guys at 280x10 2.8ghz on a64 at 1:1 2-2-2-5 runing 30s is smoking for low cpu power and fast scoring..

what ram timings are you running here macci??

[macci]

280x10 2.8ghz on a64 at 1:1 2-2-2-5 runing 30s is smoking for low cpu power and fast scoring..
Yea sure is - the A64 of course is a lot better clock to clock.
But this chip is smoking for low CPU cost (~150€) and fast scoring :D

RAM at 1:1 2-2-2-5 of course ;)

[nailbomb]

macci,

How are you cooling the Prescott if I might ask? I would imagine subzero something ;)

Since its a 133 part I would imagine it would run on my old P4PE eh?

[macci]

Ah sorry forgot to mention that. Its a R404 modded Mach2..
http://www.akiba-pc.com/e107_images/articles/mach2/extrafan_front.jpg
with extra fan mod :D

[paul007]

Macci has a mach II?? lol :)

I see how you had to add another fan to pull it out of factory conditions ;)

Oh and sorry I just now saw that its a prescott your running I thoiugh that was a p4EE wow only 4.4ghz and almost 29s wow :)

I want to live in your town you have so much fun with this hardware :)

[tictac]

hehehe... athlon xp 1700+ watercooling

BH5 single channel.... :D

[crazyboyrs]

Wow..
how come so fast one
?
Nice to see AMD wit such result !
GreAT JOB

[daniel_tin]

P4C800 | 2,4GHz@4,5GHz | 4x256mB FSB251 2-2-2-5 | Prometeia Mach 1|

[dpa]

were can I buy a 2.4A? nobody in Norway sells one.. :(

edit: I see akiba.fi has this cpu... to models...

Intel PENTIUM 4A 2.4GHZ SKT478 FSB533 1MB CACHE BOXED 162.00€
Intel PENTIUM 4A 2.4GHZ SKT478 FSB533 1MB CACHE BOXED SPECIAL-erä (4kpl)! 150.00€

wtf does special era mean?

[macci]

daniel_tin, can I have you chip please?? :D
Thats one good CPU :toast:
Have you tried the 8M SuperPi test yet? Should give you a great result!

[dpa]

Originally posted by macci
daniel_tin, can I have you chip please?? :D
Thats one good CPU :toast:
Have you tried the 8M SuperPi test yet? Should give you a great result!

what is the difference between:

Intel PENTIUM 4A 2.4GHZ SKT478 FSB533 1MB CACHE BOXED 162.00€

and:

Intel PENTIUM 4A 2.4GHZ SKT478 FSB533 1MB CACHE BOXED SPECIAL-erä (4kpl)! 150.00€

[macci]

dpa, check ur PM ;)

[ultron5]

Originally posted by daniel_tin
P4C800 | 2,4GHz@4,5GHz | 4x256mB FSB251 2-2-2-5 | Prometeia Mach 1|




HOLY :banana: :banana: :banana: :banana:!!!!1111 :D

N1 rofl its just amazing :toast:

[Crankster]

My golly gosh, a veritable monster u have there daniel_tin!
That cpu coupled with a nice 9800 XT and i think you could scare teh big guns!

[cpulloverclock]

Originally posted by macci
as far as the world records go..

P4EE record is at 24sec (5269MHz)
FX-51 is at 26sec (3304MHz)

P4E 2.4A record is 27sec (4736MHz)
A64 3400 record is 27sec (3174MHz)

all ln2 cooled yes, and the winner is TAM

http://www16.big.or.jp/~bunnywk/cgi-bin/superpi.cgi#24200403170406

http://www.geocities.co.jp/SiliconValley/5883/result/32ee/24-5269.gif

[daniel_tin]

Originally posted by macci
daniel_tin, can I have you chip please?? :D
Thats one good CPU :toast:
Have you tried the 8M SuperPi test yet? Should give you a great result! Hi All !
Macci, I have only one ;-)

8M with 12x248 ~= 4,47GHz ---> 5m27s

[tictac]

Originally posted by crazyboyrs
Wow..
how come so fast one
?
Nice to see AMD wit such result !
GreAT JOB

:D
Abit NF7-S v2.0, D22Alpha1
Barton 2500+ = 3.0GHz
2x256 KHX3000 cas2-2-2-5, CPU Interface ON
Co2 Cooling

cheers
:toast:

[tictac]

emmm... sorry asking... is there any DFI Lan Party B or DFI Infinity (nForce2)

firing up 3.0GHz speed yet? :D

[dpa]

macci, check your pm...

[o27]

Damn these A64 is fast. Heres my 35s sec. wiht in-a-box air and on-the-fly oc!

[mongoled]

tictac,

Here is mine at 2.8ghz, water cooled fans at 5v :)

http://homepage.ntlworld.com/dresuk03/2800mhz-super_pi.jpg

As u can see lots of background services running, will try higher after i finished breaking the new cpu and mobo in

mong

[bias_hjorth]

nice one tic´tac..

somebody ´should me this thread sticky again.. :)

[macci]

daniel_tin, Very nice :toast:

That 32M result would be #3 in the 32M rankings (http://holicho.lib.net/pi3355/pi3355.htm)!

[mongoled]

Ok ive got an update

:)

http://homepage.ntlworld.com/dresuk03/2850_super-pi.gif

mong

[daniel_tin]

Originally posted by macci
daniel_tin, Very nice :toast:

That 32M result would be #3 in the 32M rankings (http://holicho.lib.net/pi3355/pi3355.htm)! Thx for the reference :)

[dpa]

what is your steppings on these 2.4A macci and daniel_tin?

[SAE]

Hey guys.

I already managed a 33m 32M superpi bench before with an xp-barton 2500+ at 2,8+ but with my dfi lanparty b I am not able to break 40minutes :mad:

Could it be the servicepack 2 I am now using, before it was no.3 with win2k... ?

I always push my board hard with max timings and cpc on and cpu int aggressive... at 11x260 with maxed timings I only get around 40minutes and I wonder how it can be?

[macci]

cascade results w/ 2.4A (so far..):

1M:
http://www.akiba-pc.com/e107_images/articles/24a/spi_4556_29sec_s.gif

8M:
http://www.akiba-pc.com/e107_images/articles/24a/24a_spi8m_5m18s_s.gif

[Try-this]

woot :slobber:

damn macci that 2.4A is fast..., why is it so fast?

[Learn]

new best time for me

31s :D

http://learn.chez.tiscali.fr/3.0C/4377-31s.png

32M
http://learn.chez.tiscali.fr/3.0C/4323-32M-29-04.png

[macci]

old 3.0C (looks like it has got some extra speed during the last 2months - used to max at 4206):
http://www.akiba-pc.com/e107_images/articles/30c/4260_spi1m_32sec.gif

In 1:1 mode it reaches 34s limit at only 3821MHz ;)
http://www.akiba-pc.com/e107_images/articles/30c/3821_spi1m_34sec.gif

[dpa]

macci: what is the stepping on your 2.4A?

[S!1v3rB@cK_Dk]

When i ran 12.5x200 I did 44sec with my 2500+

When i run 11x225 it will do 40sec

4sec of just by running 225MHz run instead.. :)

[Try-this]

247,6*10 = 38 sec :D

I'll update with picture later...


Update, picture:

http://www.try-this.dk/38sek.jpg

[tictac]

Originally posted by bias_hjorth
nice one tic´tac..

somebody ´should me this thread sticky again.. :)

bias_hjorth....

its Mr Dani score not mine...(i dont have computer :( ) he is my beta tester

hey he get 33sec also... same as ur A64...hehehe :D

n dry ice cooling....

Super PI 1M =33sec

http://downloads.modlabs.net/bios/pic/dani3.gif

[bias_hjorth]

awesome.. :slobber:

Then I´ll guess I have to improve. :)

[zyx]

.

[ojdr2001]

My best result:

http://66.97.34.139/spi34.JPG

[gabbax]

Its old, but its a 35 s run.

2.6C L321 nV Mii cooled

http://w1.825.telia.com/~u82507271/superpi35sec.JPG

[ultron5]

35s are doable with only 3850MHz! ;)

[ultron5]

Originally posted by macci
old 3.0C (looks like it has got some extra speed during the last 2months - used to max at 4206):
http://www.akiba-pc.com/e107_images/articles/30c/4260_spi1m_32sec.gif

In 1:1 mode it reaches 34s limit at only 3821MHz ;)
http://www.akiba-pc.com/e107_images/articles/30c/3821_spi1m_34sec.gif

Impressive!! :toast:

mmmh, I only get 35s with 3890MHz! with 259MHz Ramspeed. You only have 3821MHz Core and 255MHz Ram. That is 70MHz less CPU and 4MHz less Ram. I have the P4C800-E.

http://mitglied.lycos.de/coolinglimit/Hardwarepics/SL6Z3/SuperPI_324.png

Is there a secret in benching SuperPI? Please tell us! :D

[shidokanjohn]

:) With new setup

[LardArse]

Here's my Cascade-cooled P4 3.4EE 27 second SPi run on IC7 339FSB:

http://bravo.ausgamers.com/lardarse/lard/27sec.JPG

I think its getting close to 26s as it hits 27S just a bit below 4.7Ghz.

[LiMPAN]

Very nice Lard!
Is that 5/4 with some nice bh-5's ?

[SAE]

Originally posted by LiMPAN
Very nice Lard!
Is that 5/4 with some nice bh-5's ?

No. 1:1 ;)

BH-4. Has been out since 1st April :ROTF:

I think he's on 5:4... :)

[LiMPAN]

Originally posted by SAE
No. 1:1 ;)

BH-4. Has been out since 1st April :ROTF:

I think he's on 5:4... :)


well... he could be on 3:2:stick:

[SAE]

Originally posted by LiMPAN
well... he could be on 3:2:stick:

Hey. I did not want to make you angry. :(

It's just been fun :)

But I think this performance follows a strong ram clock... So that's why I finally agreed with you :D

[cpulloverclock]

OMG :slobber:

memesama get this time with his 3.2E ES in air
30s at 4161MHz
http://membres.lycos.fr/cpulloverclock79/20040418093539.1.jpg

[LardArse]

I'm on 3:2. There's a stinky 280 FSB wall with 5:4 on my board.

[SAE]

Originally posted by LardArse
I'm on 3:2. There's a stinky 280 FSB wall with 5:4 on my board.

:eek: No. Too bad :(

There's no fix?

[LardArse]

VDD/Vdimm/VTT was done but not VAGP. Anyhows I'd still not be able to run 339 FSB with 5:4 so it sort of balances out at high FSB 3:2

[macci]

mmmh, I only get 35s with 3890MHz! with 259MHz Ramspeed. You only have 3821MHz Core and 255MHz Ram. That is 70MHz less CPU and 4MHz less Ram. I have the P4C800-E.
1:1 mode is clock to clock faster than 5:4 mode. Also use Win2003 server OS for SPi 1M :)

[ultron5]

Originally posted by macci
1:1 mode is clock to clock faster than 5:4 mode. Also use Win2003 server OS for SPi 1M :)

Ok then I will try it on Win2003! THX! :)

[cpulloverclock]

my lowest frequency for 36s, I think with a better fsb It would give 2270MHz
http://membres.lycos.fr/cpulloverclock79/36s..JPG

[derbis]

Not really fast and far away of your times, but my pers. best try with my system...

http://mitglied.lycos.de/d3r8is/pi.JPG


I think a bit more MHz and i get another second, cause till 235xMHz nothing change.

Changing my Samsung CC4 for some Infineon 6A for better Timings dont gave me the expected effect.

btw, sorry for my english ;)

[SAE]

Originally posted by derbis
Not really fast and far away of your times, but my pers. best try with my system...

Not bad at all my friend :thumbsup:

But try to get some khx3200 non-a at K&M Electronics :D
If they still have some it will very likely be bh-5 (and it's cheap there now).

[SAE]

A new 32m one :D

[xsky]

P4E 3,0@4,4 VapoLS -20c 1,64V
P4C800-E FSB 296 (Droop+Vdimm Mod)
2*256MB KHX 3200 BH5 237MHz 2-2-2-5 (3,2V)

1M: 29s

[LardArse]

Is it me or is the Prescott significantly faster than the EE @ 8M SuperPI?

My EE @ 14 x 334 is slower than Daniel Tin's Prescott @ 8M SPI?
Ran on Win XP.

http://bravo.ausgamers.com/lardarse/lard/8mspi1.JPG

[macci]

Yes Prescott is a lot faster on that one :D

http://www.akiba-pc.com/e107_images/articles/24a/24a_spi8m_5m18s_s.gif

[derbis]

Originally posted by SAE
Not bad at all my friend :thumbsup:

But try to get some khx3200 non-a at K&M Electronics :D
If they still have some it will very likely be bh-5 (and it's cheap there now).

Really? I will try to get some of them, but i need a better Barton too. My DFI Infinity will come this or next week but my CPU is locked :(

EDIT: Are there also BH5 on PC 3500 KHX http://www.kmelektronik.de/root/shop4/auswahl.php?ArtNr=4112

cause the 3200er are not available :(

[Tom Holck]

Originally posted by macci
Yes Prescott is a lot faster on that one :D




Past 4 Ghz Prescott is faster than old P4. The EE has larger L3, but around 4400-4500 the Prescott takes over.

Before the P4@EE was on top of M8

now its FX53-Prescott-P4EE-FX51--

My FX53 has arived hope soon to go sub 4.44:D

[shidokanjohn]

argggg i 'm trying for 30 sec but mem can't go higher...i will try with two sticks BH-6 :D
My bh-5 seems not to like more than 3.5 vmem:(http://www.thelab.gr/attachment.php?s=&postid=33130

[zyx]

:D

[TheInVisibleGod]

P4 2.8C@4.2 cooled by mach II r134a
1M: 33s :D

http://members.netmadeira.com/caires/33s.gif

[Orak]

Originally posted by TheInVisibleGod
P4 2.8C@4.2 cooled by mach II r134a
1M: 33s :D

http://members.netmadeira.com/caires/33s.gif

are you crazy ? over 2v on a P4 is not safe at all.. :eek:

[SAE]

Originally posted by Orak
are you crazy ? over 2v on a P4 is not safe at all.. :eek:

IMHO he only uses that much for benching ;)

[ultron5]

I had 2.23V running on a m0 P4, no problems with SNDS! :D

Temp was +12°C loaded /w R404a ^^ :cool:

[TheInVisibleGod]

Running a P4 with 2v cooled by phase-change for about 10min is more than safe... :p:

[K32A]

I'm doing 36 sec. with my A-data PC4000 @480MHz - 3.0-4-4-8

Screenshot: http://keza.port5.com/super_pi!.jpg

[Tom Holck]

Originally posted by K32A
I'm doing 36 sec. with my A-data PC4000 @480MHz - 3.0-4-4-8

Screenshot: http://keza.port5.com/super_pi!.jpg

You must have the ram-timings better.
Can you improve mem-volt on the MOB?
or you might improve the 3.3volt line on your PSU!
;)

[K32A]

The highest volt I can give the mem without a mod is 2.9v - But it does'nt matter.... I just bougt som KHX3200 BH5 and sold my A-data... So maybe i'm going to do a mod...

[bias_hjorth]

with bh5 that would be a great idea.. With only 2.9 juice you wont be able to pass 240MHz

[K32A]

bias_hjorth - I know that, but i think i will get a vmem mod fixed ;)

Do you think they will run 240 fsb with only 2.9v?

[centaur]

whats about 37sec with a h2o-cooled tbred 1800+? :)

[K32A]

Originally posted by K32A
The highest volt I kan give the mem without a mod is 2.9v - So maybe i'm going to do a mod...

Du any of tou guys know a good guide to do a vmem on my motherboard?

[aoc007]

Originally posted by K32A
Du any of tou guys know a good guide to do a vmem on my motherboard?

http://www.vr-zone.com/?i=192&s=1

[K32A]

Thanks... But it's very hard to see what they are doing... So maybe a more specifik guide`?

[bias_hjorth]

Originally posted by K32A
bias_hjorth - I know that, but i think i will get a vmem mod fixed ;)

Do you think they will run 240 fsb with only 2.9v?


sure if you´re lucky they do ;)

[K32A]

Originally posted by bias_hjorth
sure if you´re lucky they do ;)

They will only complete a Super pi 1M test at 227 fsb at 2-2-2-5 2.9v

[bias_hjorth]

then you´ll need vmod my friend :)

[K32A]

Yes i do ;) And i am looking for an easy guide :) So please help me :D


EDIT: I found a good guide :) http://www.xtremesystems.org/forums/showthread.php?s=&threadid=27805

[cpulloverclock]

by newbeetle

M/B�FABIT NF7 V2.0 ‰ü ( C3C003401 ) / BIOS�FNF7D_23



CPU�FMobile Athlon XP-M 2500+ 0351MPMW / L12‰ü

CPU CoolingÂ�FÂ�uÆ’NÆ’Å:banana:‚Ê‚¢‚ă}Æ’XÂ�IPro‚ QÂ�vÂ�•Â�uÂ�^Â�E’¹‹Â�‚_‚ñÂ�Ifor AMD64Â�v+LN2
Chipset Cooling�FSwiftech MCX159-R +Dry Ice


Memory�FTwinMOS PC2700 BH-6 256MB x2 / 5-2-2-2.0



VGA�FNVIDIA GeForce 2 MX400 AGP 64MB

HDD�FMaxtor 5T040H4 /U-DMA 5 (ATA100)

PowerSuplly�FZippy-460WS�i3.3V‰ü�j



Vcore�F2.10V�i��’è�j/ Vddr�F3.33V�iŽÀ‘ª�j/ Vdd�F1.90V�iŽÀ‘ª�j/ Vio�F3.78V�iŽÀ‘ª�j

OS�FWindows Server 2003



�õ�l�FCPU�{—¦16.5�{ / LN2—â‹p / 8rdavcore-0.8.5bŽg—p

http://homepage2.nifty.com/NewBeetle/img155.gif

[zyx]

:p:

[K32A]

cpulloverclock and zyx

Nice overclocks! :P

[bias_hjorth]

Originally posted by zyx
:p:

amezing:slobber: :slobber: a 1 sec faster on you´re on par with the nr.1 barton :) go 4 it :p: :D

[enduracell]

zyx's score is uppon unmoded Lanparty mobo and Prommie 404 :D

[robsession]

What's super pi?

[nutcase]

AnyBody else Crazy enough Other than me to run the 32M Test :stick:

Test is Great for checking stability


P4C800-E Dlx
P4 3.2C
Ocz PC3200 Plat LE, 1:1 @ 2-2-2-7
Cpu Water Chilled

[SAE]

Hehe. Already done it ;) It has to be somewhere in this thread. But for you, here ya go :D

[Learn]

Originally posted by hag6br
AnyBody else Crazy enough Other than me to run the 32M Test :stick:

Test is Great for checking stability


P4C800-E Dlx
P4 3.2C
Ocz PC3200 Plat LE, 1:1 @ 2-2-2-7
Cpu Water Chilled

my best, at this time

http://learn.chez.tiscali.fr/3.0C/SPI-32M-4350MHz.png

http://learn.chez.tiscali.fr/32M.php

[Huhn]

does dualchannel affect the 1mem test? asking because i got 34 sec by now with singlechannel on an prescott4,15ghz with memory@ 238mhz cl2-2-2-5

[OwcA]

It ought to.

[macci]

asking because i got 34 sec by now with singlechannel on an prescott4,15ghz with memory@ 238mhz cl2-2-2-5
My dualchannel 2.4A gets the 34sec limit at 3801MHz (211FSB) (http://www.akiba-pc.com/e107_images/articles/24a/34sec_3801mhz.gif) so yes it does make a difference.

[LiMPAN]

Old one.

http://w1.155.telia.com/~u15513671/35.JPG

[Try-this]

Improved from 38 sec to 36 sec, on my new ghetto waterchiller (so far :))


Picture:
http://www.try-this.dk/36sek.jpg


EDIT: for pictures of chiller, go here:
http://www.xtremesystems.org/forums/showthread.php?s=&threadid=34458

[Edward2]

Here is my best so far on my 3.0C/P4C800-E rig:

http://users.adelphia.net/~youmansj/images/Super%20PI%2036sec.jpg

[Tom Holck]

Just done

22.29 in SuperPiM32.

The Cascade can handle everything in 64 bit OS under 2 volt.
my highest OC under 2 volt is 3300.
Then the multi must be 14 (13 is to high to fastest timings)
Easy.

If I try higher than 2 volt It hold for about 20 minuts, then the Cascade gets hot.
I'm close to that point, where I can finish BEFORE its gets hot
;)
That like "Lucky Luke ":D

[Learn]

nice score :D
Congrats Tom Holck

[Verdict]

i test my 2.4A with C02, and i think this enough this time...

next time i take some LN2 and i have to mod this mobo first and get 3.0E ;)

http://http://verdict.puuhis.net/2.4A%20Prescott%20Tuloksia%20-NEW-/sp8m_5_22.jpg

http://verdict.puuhis.net/2.4A%20Prescott%20Tuloksia%20-NEW-/sp1m_29sek.JPG

[Diablo II]

1,8V with prescott? How is it possible? Everyone has no-boot overo 1,65V

[bias_hjorth]

Originally posted by Diablo II
1,8V with prescott? How is it possible? Everyone has no-boot overo 1,65V


CO2 cooling could be the reason ;)

[Tom Holck]

Originally posted by bias_hjorth
CO2 cooling could be the reason ;)

Yea agree, bias_hjorth,
I remember when everybody said that 1.8/1.85 was the max on the old P4. With cascade cooling sub -100c the best OC was close to 2 volt.

I have not tried Prescott yeat (FX-53 is better at this point, like a 6+Ghz Prescott!!*) but with sufficient cooling the Prescott can take volt, for sure.

*2400@3300x14 is like a FX-62:slobber:

[bias_hjorth]

Originally posted by Tom Holck


I remember when everybody said that 1.8/1.85 was the max on the old P4. With cascade cooling sub -100c the best OC was close to 2 volt.



yup and that not even long ago :)


Originally posted by Tom Holck

I have not tried Prescott yeat (FX-53 is better at this point, like a 6+Ghz Prescott!!*) but with sufficient cooling the Prescott can take volt, for sure.


6Ghz pressi should be a "tad" bit faster than a fx53 even at impressive 3300 :)

[Huhn]

someone in germany feeds his 2.4er prescott with 1,75 with only mach2 and he gets an astonishing 4,4ghz super pi 1m time of 29 sec ;)
sry for tipo. meant 29 sec and not 20 sec ;)

[bias_hjorth]

Originally posted by Huhn
someone in germany feeds his 2.4er prescott with 1,75 with only mach2 and he gets an astonishing 4,4ghz super pi 1m time of 20 sec ;)


lool 20sec.. yeah sure he is ;)

[Edward2]

I managed to knock a second off my time:

http://users.adelphia.net/~youmansj/images/Super%20PI%2035%20sec.jpg

[Verdict]

With Asus P4C800 Deluxe i get only 1.67v for core but i buy Abit IC7 Max3 and i but 1.76v from bios and it works :D

and other picture :D

http://verdict.puuhis.net/2.4A%20Prescott%20Tuloksia%20-NEW-/sp8m_5_22.jpg

[aristidis]

:D This is my best until now but i have to test some bios settings and i beleive that i get a better resault. I will also test with my two sticks of GEIL PC4200 that the are able to do 310fsb 1:1.


http://briefcase.pathfinder.gr/download/arispan12/21501/252331/0/Pi+30+4636.jpg

[ant1]

I think I will replace the CPU, it´s a bad clocker.

[dpa]

look in my sig.. 3.0E @ 4.35Ghz.. = 31sek. i ran 5:4 2-2-2-5, and winxp.

iam looking for a SL79A now.. the SL79L is a "bad" overclocker..

[ant1]

When I say bad i mean baaad. It sucked at watercooling doing 3.5-3.6 and it sucks at phase change doing only 38xx-39xx. Looking for a 2.8m0 now.

[cpulloverclock]

Memesama is the best!!!!!!

New World record with a P4 3.2E and LN2

http://members.jcom.home.ne.jp/3233730401/4m43s.jpg

[Verdict]

NICE ONE... 200€~prosessor rox

:slobber: :slobber: :slobber:

[cpulloverclock]

Originally posted by Verdict
NICE ONE... 200€~prosessor rox

:slobber: :slobber: :slobber: more information

M/B：ASUS P4C800 3BMG/ BIOS：1016
CPU：Pentium4 3.2EGHz SL7B8 3412A536
RAM:KHX3500 256MB×2
CPU Cooling：クリぬいてマス！PRO3　LN2
Chipset Cooling：無改造
Memory：Kingston KHX3500　CL2　256MB x2
VGA:ASUS V9520（AGP)
HDD：IBM DTLA　１５G
Power suplｌｙ：Zippy 460W改
Vcore：1.815V/ Vddr：3.34V/ Vio：3.69V
OS：Windows Server 2003
Clock：5240Mhz　FSB327.53Mhz×16




world recordddddddddddddddddd!!!!!!!!!!!!! :slobber: :slobber: :slobber: :slobber:

with a 3.2E at 1.815v!!!
http://membres.lycos.fr/cpulloverclock79/20040503041848.1.jpg
http://membres.lycos.fr/cpulloverclock79/20040429144106.1.jpg
http://membres.lycos.fr/cpulloverclock79/20040429144122.2.jpg

[aoc007]

Very impressive:slobber: Does he have any other benchmarks with that cpu?

[cpulloverclock]

Originally posted by aoc007
Very impressive:slobber: Does he have any other benchmarks with that cpu? only Pi 8M....

[OneProdigy]

Great work, cpulloc!
But why does the fpo# batch on the heatspreader NOT match the one on the package?

[bias_hjorth]

Originally posted by OneProdigy
Great work, cpulloc!
But why does the fpo# batch on the heatspreader NOT match the one on the package?


It does.. look closely and you´ll see :)

btw. that memesame is one sick dude...
:slobber:

[zakelwe]

Lucky for the Japanese the P3.2E only does Superpi well .......

Only half jopking here.

Still, nothing to be sneezed at :)

Regards

Andy

[OneProdigy]

Originally posted by bias_hjorth
It does.. look closely and you´ll see :)


My bad, sorry...mixed it up with the number next to the logo at the bottom of the hs. ;)

[cpulloverclock]

Originally posted by OneProdigy
Great work, cpulloc!
But why does the fpo# batch on the heatspreader NOT match the one on the package? he has two 3.2E

[aoc007]

I wonder how his 5.2ghz presscott compares to Tom Holcks 3.3ghz fx in 1m?

[cpulloverclock]

Originally posted by aoc007
I wonder how his 5.2ghz presscott compares to Tom Holcks 3.3ghz fx in 1m? 24s I think

[SAE]

Have also improved :D

Superpi 1M:

[Learn]

nice one, :toast:

[SAE]

Originally posted by Learn
nice one, :toast:

Thanks :)

Been working hard for it :D

[dpa]

Originally posted by cpulloverclock
24s I think

ask memesama to run super pi 1M @ 5.3Ghz... :D it should KICK ass!

[cpulloverclock]

Originally posted by dpa
ask memesama to run super pi 1M @ 5.3Ghz... :D it should KICK ass! ok but 24s is already the world record

24s at 5268MHz with a P4EE by TAM I believe

for 23s, 5.4GHz is needed

[zyx]

:)

[MAJT]

Originally posted by cpulloverclock
only Pi 8M....

I would love to see a 3dmark at that speed or a pcmark :slobber:

[JacobHansen]

heres my DigiDice with a Mach II mounted on ;)

[cpulloverclock]

by Memesama, he's a DEUS????

with his 2.8A :

bad time, 23s was possible
http://membres.lycos.fr/cpulloverclock79/20040508013115.1.jpg

M/B�FASUS P4C800 3BMG/ BIOS�F1016
CPU�FPentium4 2.8AGHz SL7D8 L411A842
CPU CoolingÂ�FÆ’NÆ’Å:banana:‚Ê‚¢‚ă}Æ’XÂ�IPRO3Â�@LN 2
Chipset Cooling�F–³‰ü‘¢
Memory�FKingston KHX3500�@CL2�@256MB x2
VGA:ASUS V9520�iAGP)
HDD�FIBM DTLA�@‚P‚TG
Power supl‚Œ‚™�FZippy 460W‰ü
Vcore�F1.744V/ Vddr�F3.42V/ Vio�F3.60V
OS�FWindows Server 2003
Clock�F5387.2Mhz�@FSB256.5Mhz�~21
http://members.jcom.home.ne.jp/3233730401/538724s.jpg


4'33s : a new WORLD RECORD
M/B�FASUS P4C800 3BMG/ BIOS�F1016
CPU�FPentium4 2.8AGHz SL7D8 L411A842
CPU CoolingÂ�FÆ’NÆ’Å:banana:‚Ê‚¢‚ă}Æ’XÂ�IPRO3Â�@LN 2
Chipset Cooling�F–³‰ü‘¢
Memory�FKingston KHX3500�@CL2�@256MB x2
VGA:ASUS V9520�iAGP)
HDD�FIBM DTLA�@‚P‚TG
Power supl‚Œ‚™�FZippy 460W‰ü
Vcore�F1.744V/ Vddr�F3.42V/ Vio�F3.60V
OS�FWindows Server 2003
Clock�F5374.6Mhz�@FSB255.9Mhz�~21

http://members.jcom.home.ne.jp/3233730401/8384m33s.jpg



Soon 5.6GHz!!!!!!!

[JacobHansen]

I find it very hard to belive that he can hit 5.3Ghz with 1.6 Vcore and with a 21 Multi.

and he is NOT using a ES??

[aoc007]

Theres no 2.8E with 533FSB right? Why then does cpu-z show 21x multi and 2.8ghz, is it unlocked?

[bias_hjorth]

well Its MEmesama the LN2 guru.. So its 100% correct.. one of the best in the game IMHO :)

[cpulloverclock]

Originally posted by aoc007
Theres no 2.8E with 533FSB right? Why then does cpu-z show 21x multi and 2.8ghz, is it unlocked? a 2.8E with 533 = 2.8A

21*133 = 2800

2.4A = 18*133

It's a new processor

[aoc007]

I didnt hear about Intel releasing a new "A" model Prescott, is there going to be a full line of them all the way to 3.4GHz?

[Slickthellama]

Originally posted by aoc007
I didnt hear about Intel releasing a new "A" model Prescott, is there going to be a full line of them all the way to 3.4GHz?

assuming the 3.4 would have a 133MHZ fsb that means the multi = 3400 / 133 = 25.56 :slobber: :slobber: :slobber:

that means a FSB of 200 = 5112MHZ!!! :slobber: :slobber:

[aoc007]

That would be very cool, itd take the fsb limitations of the locked p4s completely away.

[Ragnarok]

http://members.iinet.com.au/~zzhang/superpi.jpg

ram is not running @ 273 (I :banana: :banana: :banana: :banana:en wish), only @ 261 using 10.5 multi

[misteroadster]

does anyone had tested this ? :
news of 1h00
Driver For mem controler A64 by AMD:
http://www.materiel.be/listnews.php?start=0#news5296

[cpulloverclock]

Originally posted by misteroadster
does anyone had tested this ? :
news of 1h00
Driver For mem controler A64 by AMD:
http://www.materiel.be/listnews.php?start=0#news5296 bad thread

[dpa]

that is sooo fast...!

23sek is awesome (he will make it..)

[Endre]

I managed to get 35s with my air cooled XP-M. :)

http://home.no.net/endreke/bilder/PC/SuperPI35s.jpg

NF7, XP-M 2400 35W "Y" IQYFA0345SPMW, TwinMOS BH-5, MCX462-V w/ Delta 80CFM 80mm

[SAE]

Originally posted by Endre
I managed to get 35s with my air cooled XP-M. :)

http://home.no.net/endreke/bilder/PC/SuperPI35s.jpg

NF7, XP-M 2400 35W "Y" IQYFA0345SPMW, TwinMOS BH-5, MCX462-V w/ Delta 80CFM 80mm

Really nice :thumbsup:

/Edit

How cold was this air? ;)

[Endre]

Originally posted by SAE
Really nice :thumbsup:
Thanks. :)

Kind of a shame it's getting so hot here now, I could get much more out the chip when it was colder. :D

[Henry]

Here's my mobile 2500+ result :

http://img4.imageshack.us/img4/2254/superpi_2860mhz.JPG

Watercooling (14c water).

[Endre]

Great speed Henry, but you've got some tweaking do do! You're 60 MHz higher on the CPU and 16.5 on the FSB, but you still get the same result.

[Henry]

Thanks Endre :)

But i think 60mhz clock / 16.5mhz fsb advantage is not enough to get 1 sec in superpi 1mb.
With desktop Barton 2500+ @ 2.63 Ghz (10.5x250) i can get 37 sec, SCREENSHOOT (http://img4.imageshack.us/img4/1701/2630mhz_superpi.jpg). 230mhz clock / 10mhz fsb advantage (2.86 ghz - 11x260) just give me 2 sec faster.

[IamAnoobieCheez]

Henry,

you turned off CPC?

nice clock for the cooling you provided. but all i need is 250fsb at similar cpu clock as yours to get 34sec....

i know you enabled everything when you ran sandra mem bench at those fsbs, but i suppose you had to disable goodies to get to 2.85'ish ghz? it seems so.

[Henry]

IamAnoobieCheez :

SuperBypass : Enabled
Sync Mode Memory Bypass : Enabled
Data Scavenged Rate : Fast,
Command Per Clock : Enabled
11-2-2-CL2-9-12, 4/29 bios.

[IamAnoobieCheez]

CPU aggressive on?

APIC enabled? :D

what brand/model memory sticks are they.

how is that 4/29 bios.. anybody getting good tight performance with that bios version?

what did that x-x-x-x-9-12 setting do to you based on your experience? faster or slower?

[Henry]

CPU Interface : Aggressive.
APIC : Enabled :)

I use 2x 256MB Twinmos PC3200 (BH-5). Never compare bios 4/29 with 1/21 yet in superpi, but in sandra mem bench and 3dmark2001 the score is same.

Maybee u use "special windows tweaks" :D

[IamAnoobieCheez]

thank you very much for your co-operation mr. Henry.


quote "Maybee u use "special windows tweaks" :D"

oh i forgot to mention that... hmm.. i use win2k ntfs sp2 dx8.1 and no special tweaks..

:)