Nvidia 7950GX2 + dual evap

[CornerJack]

Today, I installed my dual evap (http://www.overclex.net/atelier/226/Dual-Evap) of Piotres on a Nvidia 7950GX2.
I used it with "GX2 Spacer kit" of Swiftech.
Tomorrow, I make test and I give you the results. For the moment, the graphic card isn't modded.

http://www.overclex.net/data/images/articles/hardware/atelier/2007-03-28/gx1.jpg

http://www.overclex.net/data/images/articles/hardware/atelier/2007-03-28/gx4.jpg

http://www.overclex.net/data/images/articles/hardware/atelier/2007-03-28/gx5.jpg

http://www.overclex.net/data/images/articles/hardware/atelier/2007-03-28/gx6.jpg

http://www.overclex.net/data/images/articles/hardware/atelier/2007-03-28/gx7.jpg

[Jort]

Go jack Go :D

why no Vmod? ;)

[CornerJack]

Go jack Go :D

why no Vmod? ;)
the next week :D

[Gebba]

haha very nice locking rig :D

whats the core temp under load?

[vanovich]

:D i like ,nice tight insulation ,good work .looking forward to some reults .

[blind_ripper]

nice jack push it all the way m8

[massman]

Great work :)

I really like your work, bro, always clean and tidy !

[v|aDy]

Nice, very nice...
Waitin' result :toast: Pencil Mods - 5 minutes ;)

[Dekara]

Nice setup, we expect nice result too :) .

[LordofDoom]

Wow, I'm expecting big numbers in '05, and as said... why no Vmod?

EDIT: I see the "No Vmod yet," sorry to speak so presumptuously.

[Radamanthys]

Wow nice work CJ . Regards i wait to see the benchs :)

[Pedro Rocha]

Nice work

Moved from overclock to phase change section

When you have some bench results please post it on 3D Team section

[billdavis]

what are the clocks you get with stock volts?

id like to do this but there is no 1m x 1m x 1m case to put 2 phase units in

[Sneil]

i noticed that the steel hold-down plates are directly in contact with the evaporator so you'll want to insulate those as well. Otherwise when the frost melts and drips, and you decide to fire up your rig again, bye-bye 7950gtx. I've got those same hold down plates from piotres.

[Kobalt]

Does anyone else think its funny that he has dual phase for his gfx and then air cooling for the cpu :p:?

[[XC] gomeler]

I chuckled a bit, I'm hoping there is atleast a waterblock for the CPU.

[JT from Russia]

Very nice, need great result.

[CornerJack]

Thank you !


haha very nice locking rig :D
whats the core temp under load?
Test today :D


Nice work
Moved from overclock to phase change section
When you have some bench results please post it on 3D Team section
Ok Pedro.


i noticed that the steel hold-down plates are directly in contact with the evaporator so you'll want to insulate those as well. Otherwise when the frost melts and drips, and you decide to fire up your rig again, bye-bye 7950gtx. I've got those same hold down plates from piotres.
Have you pictures of you insulation ?


Does anyone else think its funny that he has dual phase for his gfx and then air cooling for the cpu :p:?
For the moment, after is LN2 for CPU :D

[LittleDevil]

Nice setup ;)

regards

[piotres]

nice setup :D

Waiting for temperatures of dual vap loaded :toast: .

Peter

[sacha35]

Nice looking, as sneil said steel hold-down plates are directly in contact get some insulation on them.

[Duniek]

nice, but where is chipset phase cooling ?:D

[Pete]

Water the SB, phase the NB and LN2 the cpu now that be kick ass!!

[Xtasy]

we have a dual evap unit from piotres too and i can tell you that your cards arent insulated enough. you need to cover really the whole graphics card with armaflex, otherwise there will be condensation everywhere. the steal holddown will freeze too, so it must be insulated

[likewhoa]

nice setup, just wish the spacer kit didn't preclude Quad-SLI on these cards.

[CornerJack]

I have begin the benchs but much condensation at the time of the benchs…

http://users.skynet.be/fb331210/gx9.jpg

http://users.skynet.be/fb331210/gx10.jpg

Moreover, one of the evaporators was not placed better, therefore, I withdrew, I dry and I reinstall with a better insulation: D

[T0bbz0n]

Ey! Very nice!

Got 7950GX2 aswell :) Just waiting for my spacer kit :D

looking damn cool!