QX6700 on the mini-cascade - 1st results

[Pedro Rocha]

To much work, finally I managed some time to do a quick test of a retail QX6700

Since Ricky made me a mini-cascade with VapoLS mounting kit, is real pratical to mount the CPU on it - even more quick than the Tuniq :D

Poor Mini-Cascade (orignal VapoLS + original Promie compressors) the heat of the 4 cores really give the cascade a hard time, the temperatures start to raise really quickly (from -70ºC on idle to -40 or less in load):(

Here is a photo :

http://pedrorocha.planetaclix.pt/QX6700_montado_na_MiniCascata.jpg


First let's find how many MIPS do I have under the hood..

http://pedrorocha.planetaclix.pt/QX6700_4500_SandraCPU82928MIPS.jpg

82 thousand MIPS ..not bad:)

Now the inevitable CineBench

http://pedrorocha.planetaclix.pt/QX6700_4600_CineBench9sec.jpg

9 Seconds ;)


Now let's check how fast can it run 4 SuperPI's in each core..

http://pedrorocha.planetaclix.pt/QX6700_4600_4SuperPI.jpg

Timings really bad since the memory are not optimized by any means..

And finally the CPU Score of 3D Mark2006

http://pedrorocha.planetaclix.pt/QX6700_4500_3DMark2006_6512_CPU.jpg

6.500 :D : almost doubles the X6800 score..eheh


I really need to test this CPU on Ricky's new 3 Stager ..anyway a few more results in the Mini-cascade in the next few days , I think is time for 3D Mark2006 action ;)

[Supertim0r]

looking really good :toast: :clap:
you got a pic of the cascade ? (or it's the one in phase section ?)

[Terminal 8]

How much you want for that mini cascade? :p:

[Gautam]

Love those SuperPI scores, and especially the Vapochill mounting on a cascade. :)

[FUGGER]

Falling right between my modded LS and tripple stage, nice mini. Good stuff

[Nanometer]

A bridge for SLI and no second card? Either you are wishful, or you forgot their isn't a second card lol. Great results. 4.5GHz quad core is amazing =-o

[overcrash86]

hi pedro,

what is the QX stepping ?

good luck under three stage :D

[Pedro Rocha]

hi pedro,

what is the QX stepping ?

good luck under three stage :D

L638A367

[Kabauterman]

Realy only 1,475 V ??? or it isn't right?

[Drag]

how do you optimize the memory?

[VictorWang]

nice mini-cascade, I love that :D
-70c idle for QX6700 is good !

[Pedro Rocha]

looking really good :toast: :clap:
you got a pic of the cascade ? (or it's the one in phase section ?)

Just use the search : http://www.xtremesystems.org/forums/showthread.php?t=121684&highlight=mini-cascade
:)

[DeToNaToR.cl]

Nice coolink fan :)

[Pedro Rocha]

Here is a result of this QX6700 air cooled - using a Tuniq Tower on the Abit A9WD

http://pedrorocha.planetaclix.pt/QX6700_3900AR_CineBench.jpg

At 1.6v with Enhaced SpeedStep and C0 active (in idle low cpu to 6x and around 1.40v) runs CineBench without any problem at 3.900Mhz, time no to bad 12 sec ;)

Temps are more than aceptable for 24/7 use at this speed :)

[VoRtAn_MaDgE]

That mini-cascade is :eek: ...damm nice work...as usual on Ricky.
That's a fine setup for 24/7 :D

[Hystrix^]

Very nice Pedro :up:

[TheJollyFellow]

I'm kinda surprised the SuperPi timing isn't lower, a X6800 does those times at 4.5-5GHz, and with twice the cores, I'd think it would do it at least a little bit better ;)

[STEvil]

try running it 4 times at once on an x6800 vs the times this gets running it 4 times at once.

[Drag]

how would you know what superpi test it is?

[Dynasty]

nice results.....3D 06 is all QX 6700 1st page ORB/8800 gtx's in sli,
without one is pretty much pointless to even attempt 06...

[Brettbeck]

Nice results!

I'm sure there will be much more once Ricky finishes that 3 stager :D!

[R @ P T O R]

good job Pedro! :toast:

[Ghostwind]

Great overclock on the QX6700 pedro.

I am trying to stabilize my QX6700 on a P5B Deluxe ATM (can boot into windows but not be Orthos stable) and was surprised to see your multipliers so high.

Do all the 680i boards unlock mulitipliers on Kentsfield up to 15 ?
or only the eVGA?

[LittleDevil]

Great results... :toast: Is it QX6700 much hotter than X6800 at same voltage and speed?

Regards

[Pedro Rocha]

Great results... :toast: Is it QX6700 much hotter than X6800 at same voltage and speed?

Regards

Yes, really MUCH hotter than the X6800 with same voltage.

This mini-cascade hold very well a X6800 at 4.900 with 1.8v - idle near -88ºc and load around -78ºC .. - with QX6700 a 1.8v load temps reach -40ºC or more.

A much firm contact with evaporator is also needed with QX6700

For double use (X6800 / QX6700) I would say a CPEV to adjust is essential - after finish their 3 stager, I'm gonna ask Ricky to put a CPEV and a better compressor on the 2nd stage on this mini-cascade.

Here is the temperatures with X6800 at 1.84v in the mini-cascade.

http://pedrorocha.planetaclix.pt/TempIgualFluke.jpg

As you can see the evap temperatures measure in the Fluke are exactly the same as the tempeatures measured in EVGA 680i Bios - nice :D

[Pedro Rocha]

Great overclock on the QX6700 pedro.

I am trying to stabilize my QX6700 on a P5B Deluxe ATM (can boot into windows but not be Orthos stable) and was surprised to see your multipliers so high.

Do all the 680i boards unlock mulitipliers on Kentsfield up to 15 ?
or only the eVGA?

Yes, I think so .. the 680i's even allow higger multi than 15x

I tested my QX6700 on the P5B Deluxe (max multi 12x) and the 965 chipset board allow much more higger FSB than the 680i

Aircooled (Tuniq Tower) my QX6700 in the P5B Deluxe runs Cinebench at 3.900 and is full Orthos stable at around 3.800 Mhz..as you can see in this pic ..

http://pedrorocha.planetaclix.pt/QX6700_P5B_3900_CineBench.jpg

[4Qman]

Yes, really MUCH hotter than the X6800 with same voltage.

This mini-cascade hold very well a X6800 at 4.900 with 1.8v - idle near -88ºc and load around -78ºC .. - with QX6700 a 1.8v load temps reach -40ºC or more.

WOW that's some serious heat load. :eek:

[NapalmV5]

http://pedrorocha.planetaclix.pt/QX6700_P5B_3900_CineBench.jpg

VS

mine,
http://img175.imageshack.us/img175/8361/cine95zo9.jpg


can anyone guess whats going on? :D

[npk]

VS

can anyone guess whats going on? :D

Winxp64 on your computer maybe?

[black_edition]

Winxp64 on your computer maybe?


or because Asus P5W64

[NapalmV5]

Winxp64 on your computer maybe?

nope, winxp32

or because Asus P5W64

hmm.. such a big difference between i975x and i965p?

[eva2000]

VS

mine,
http://img175.imageshack.us/img175/8361/cine95zo9.jpg


can anyone guess whats going on? :D

sounds like throttling ? why cause Q6600 at 3600mhz with P5B Deluxe

http://fileshosts.com/intel/Asus/P5B_Deluxe/results/G4Storm/Q6600_Kenstfield/ocz/titaniumalphaVX2/PC8000/1_2/0804/9x/533/400-400-3434_3-25-6-def_1.55-1.4-1.65-2.25/cinebench.jpg

doh wrong version of cinebench heh

[NapalmV5]

sounds like throttling ? why cause Q6600 at 3600mhz with P5B Deluxe

doh wrong version of cinebench heh

lol, yeh i get the same results @ cine 2003,

1 cpu - 627 @ 42.0
x cpu - 2011 @ 13.1

Kent @ 3604mhz 400x9

wat did u mean by throttling?


eva, would u do cine 9.5?

[Drag]

mach2 temps on oc'd qx6700.
http://rol-co.nl/images/dt200mod.jpg
http://valid.x86-secret.com/cache/127648.png

[npk]

ouch poor mach2 :( I´d like to see a chiller comparo between a kent and a conroe, somehow I think a chiller will hold temps better than a SS (commercial unit I mean).

[VoRtAn_MaDgE]

mach2 temps on oc'd qx6700.
http://rol-co.nl/images/dt200mod.jpg
http://valid.x86-secret.com/cache/127648.png

Calibrate that bastard Drag, ASAP :slapass:

But for the heat that your quad-core produces, you can't do much more :(

[Rol-Co]

mach2 temps on oc'd qx6700.
pic
validation

Drag , don't know what country you are , maybe you found this with google but its totaly wrong.
its my old step 4 kentsfield , the validation is a 500fsb show , and the 22 degrees temp on the dt is showing that the dt200 is modded to get power from the psu, so if you can't read the story with it don't post it somewhere else please.:mad:
it will give a wrong impression too people.

new kentsfield in the meanwhile and doing better
to compare with the cinebench score , air cooled

p5b dlx/tt120/g.skill 8500hz

http://82.173.172.10/Rol-Co/qx3950.JPG

[Reg-Edit]

Drag = BAD :slapass:

Stealing someone els screenshot is not the right way to get credit !!
This way no one will believe you anymore .. :cussing:

[Drag]

Damn...

[DaCoSa]

Good results Pedro!!!:toast:

regards

[anarinsk]

Look great. QX6700 is much harder to raise clock.