Will a Scythe Ninja fit in this case??

[Daveb2012]

Does any one know, i already bought the ninja, and this is the case I want. Thanks if any one knows..

http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=1225662&CatId=0

[Pinnacle]

Yes, it should. Scythe says the case has to be 19cm wide

[Daveb2012]

cool im excited. thanks!

[Nazu]

Offtopic but I didn't want to make a new thread for this. So the problem is that my temps are worst now since I upgraded my heatsink from Big Typhoon to Ninja. Its like 10 degrees hotter in idle and load than with the Big Typhoon. So what's the problem here? I used a thin layer of AS5 and the mounting seemed like it's pretty tight.
http://koti.mbnet.fi/nazu/Kone/Siilit/Scythe%20Ninja.jpg
I have the bundled fan on it and 120mm Nexus at back of the case and pretty close to the Ninja. So I would assume it has a good airlfow.

[ripken204]

remount it. temps should be the same

[Daveb2012]

Offtopic but I didn't want to make a new thread for this. So the problem is that my temps are worst now since I upgraded my heatsink from Big Typhoon to Ninja. Its like 10 degrees hotter in idle and load than with the Big Typhoon. So what's the problem here? I used a thin layer of AS5 and the mounting seemed like it's pretty tight.
http://koti.mbnet.fi/nazu/Kone/Siilit/Scythe%20Ninja.jpg
I have the bundled fan on it and 120mm Nexus at back of the case and pretty close to the Ninja. So I would assume it has a good airlfow.

Sorry about your problems, I hope I dont get this issue.

[eklipze]

hehe cool Antec p160w =P

oh on your degreees its probably the FAN since the NINJA+'s fan SUCK i suggest an aftermarket 1 tho. its optional.

the HSF =good CFM low DBA + the rare end fan [ CFM = w/e you want] === good airflow wel. better if you want low temps

[Daveb2012]

hehe cool Antec p160w =P

oh on your degreees its probably the FAN since the NINJA+'s fan SUCK i suggest an aftermarket 1 tho. its optional.

the HSF =good CFM low DBA + the rare end fan [ CFM = w/e you want] === good airflow wel. better if you want low temps

I was thinking of mounting 2 fans on mine, the stock 120 and my aftermrket Delta that puts out 4x the CFM. I obviously wouldn't have both running, but connected to a fan controller so I can toggle either of the fans off/on.

[Nazu]

Well maybe I should try the Antec Tri Speed fan and set it to medium. I used that with my Big Typhoon. Seems like the fan that came with the Ninja spins at much lower rpm.

[Nazu]

I was thinking of mounting 2 fans on mine, the stock 120 and my aftermrket Delta that puts out 4x the CFM. I obviously wouldn't have both running, but connected to a fan controller so I can toggle either of the fans off/on.
Good idea but you have to make your own wire clips for the second fan as Ninja comes with only two clips for one fan.

[agenda2005]

Well maybe I should try the Antec Tri Speed fan and set it to medium. I used that with my Big Typhoon. Seems like the fan that came with the Ninja spins at much lower rpm.

Did you get your temps down with a new fan?

[Daveb2012]

Good idea but you have to make your own wire clips for the second fan as Ninja comes with only two clips for one fan.

this is true, maybe I could modify a large paper clip to make some clips.

[goreblast]

Just for everyone's info it will not fit in a Coolermaster ATC-s4000-SX1 case. that case is only a couple of cm wider than a cdrom drive, therefore any case that is that narrow will have problems.