My first Single Stage

[hincó]

My first SS
I'm waiting for tommorow and probably i'll tank it with r 507 and POE oil
Containing:
:exclaim: Custom homemade Case made of alu and OSB walls
:exclaim:EVAP (http://forum.purepc.pl/index.php?showtopic=185634&hl=)
:exclaim: Danfoss FR 8,5g
:exclaim: Captube about (dont remember) 270 cm
:exclaim: Neo45-thermometer
:exclaim: Fan- 13cm by Thermaltake
:exclaim:SLHX
:exclaim: Condenser made of ine bigger
:exclaim: Desup
:exclaim:Power suply atx+rheobus for fan
:exclaim: Sunction 45 cm
:exclaim: r507+POE
:exclaim: and all that should be..



Case:
http://i29.photobucket.com/albums/c272/hinco_1988/buda/Image861.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/buda/Image858.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/buda/Image859.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/buda/Image860.jpg
Rest:
http://i29.photobucket.com/albums/c272/hinco_1988/ss/eeaab99a.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1028.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1029.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1030.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1031.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1041.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1042.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1043.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1044.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1052.jpg
Electronics by me :E
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1053.jpg
SLHX
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1008.jpg
SLHX sunction and evap isolated
http://i29.photobucket.com/albums/c272/hinco_1988/ss/20060518.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/20060518001.jpg
Desup
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1067.jpg
Heart
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1068.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1069.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1070.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1006.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1072.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1007.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1073.jpg
Back:
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1009.jpg
I'm sailing - looking for leaks
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1109.jpg
Here's leack you won't see cause of bad photo quality:
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1110.jpg
Taking a bath :P
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1111.jpg
It's just a little piece of photos :P
Now it's waiting for me 18 birthday :P
Oh, yeah, it will be for sale for sure ; ]]

[ICE COOL]

congretulation, nice fist unit but the electricitie is a bit dangerus with water dude.

ICE COOL

[hincó]

congretulation, nice fist unit but the electricitie is a bit dangerus with water dude.

ICE COOL
I know, i wouldn't do this, but i spend about 3 months looking for leak, friends from Poland gave me an idea of water, and i found leack when i lern it how to sail ;]]
Leak was in sunction port in Danfoss :|
I didn't expect that :(

Thermometer is now dry cause it shows good temp, so i think psu is ok too..

[LukeXE]

Nice work my friend, I`m waiting for photos with very, very low temp on evap mate ;)

[hincó]

Nice work my friend, I`m waiting for photos with very, very low temp on evap mate ;)
Sorry but i'm very unlucky with all those phase stage, i expect that tommorow morning i'll recieve no presure in it after todays 5 bar :P (just a little gift for my 18 :P )
Im scarred if condenser in enough and if cap isn't blocked (now it isnt but.. look up;] )

[GuGaCoSa]

it is my eyes or did u glued some of the connections?
Good looking slhx btw =D

[hincó]

it is my eyes or did u glued some of the connections?
Good looking slhx btw =D
It is leak lock, sum1 on XS uses it same like me :)
I gave it on all conections to make myself sure there is no leak :)

[Carlz0r]

It is leak lock, sum1 on XS uses it same like me :)
I gave it on all conections to make myself sure there is no leak :)
Leak lock is actually only meant for flare connections where it has pressure from the sides holding it in. If there is a leak on a pipe, the refrigerant will gradually "bubble" the leak lock off, or create a small path out.

[hincó]

Leak lock is actually only meant for flare connections where it has pressure from the sides holding it in. If there is a leak on a pipe, the refrigerant will gradually "bubble" the leak lock off, or create a small path out.
I believe :)
I gonna make a whole in a pipe and glue it by LL and check under some presure for a few weeks :)

[Xeon th MG Pony]

can you make a schematic? hard to see what has been don.

[epion2985]

115+v in a bath of water... very bright :caution:

[yngndrw]

Thermometer is now dry cause it shows good temp, so i think psu is ok too..
Did I read that wrong, or does that imply that you switched it on BEFORE it was dry ??? :stick: :slap:

Electrical items are fine in water as long as you dry them BEFORE use.

[hincó]

can you make a schematic? hard to see what has been don.
almost everything is done. What is not clear?
I've got 230 v :p:
I switched on thermometer after 2 days in 40*C and it is ok, i think it would show bad temps if there was some water on paths..

P.S
Starter in Danfoss is probably bad, when i was brazing suction port where was leak it probably get too much heat and i dont know what now.. :/

i'll wait with starting it for a few days i think..

[runmc]

Congrats on a first attempt :toast:

That water is going to play heck on the OSB. I would only submerge non electrical parts. Compressor, tubing, condenser, evaporator, slhx.

[hincó]

Congrats on a first attempt :toast:

That water is going to play heck on the OSB. I would only submerge non electrical parts. Compressor, tubing, condenser, evaporator, slhx.
play heck? what does it mean ? :P
I only know i've got balcony made of that osb and it is ok after winter :P:

Now i don't know if i finish it..
I'm f... furious cause i started it in march!! :[

[yngndrw]

'Good things come to those who wait.'

Stick at it. :)

[luf1c3r]

Doesn't the wood make that the system every time it is reheated but according to raisin the time?

Greetings

[godmod]

play heck? what does it mean ? :P
I only know i've got balcony made of that osb and it is ok after winter :P:

Now i don't know if i finish it..
I'm f... furious cause i started it in march!! :[

keep on working ;)
my first SS building atempt took over 3 months :D
leek in suctionline, leek in evap, leek in condensor,... but i finally did it :toast:

[hincó]

keep on working ;)
my first SS building atempt took over 3 months :D
leek in suctionline, leek in evap, leek in condensor,... but i finally did it :toast:
Did tou fired it at the end? no? But i did :p:
and i had electricity problems too :p:

[Dаvidoff]

Very well for first SS. Gats!

[hincó]

i dont know wtf :/
Evap is freezing, 0bar/15bar, but when i put finger on it, ice disapears and after few minutes comes back :|
when i put it off it have that pressures for a few minutes, and realy slowly presures equals. And what's the worst, first run was yesterday night, after it, i put it off and go sleep, when i saw today morning the static presure of 10 bar i almost died! :shock:
Just dont know what is happening.. :(

[yngndrw]

when i saw today morning the static presure of 10 bar i almost died!
Where did you measure ? High side only ?

Blocked cap tube ?

[hincó]

Where did you measure ? High side only ?

Blocked cap tube ?
no no :P
LukeXE told me it's alright with r 507
10 bars were at both low and high side
I didnt know that 2-3 bars static presure is not for r 507 :P
Captube is probably ok, cause evap is freezing, is it possible that it is blocked only in for example a half ?

[hincó]

http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1135.jpg
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Image1134.jpg
Dont look at that thermo, i think it shows temps about 2*C to high
A lot of work is waiting for me :p:

[LukeXE]

I didnt know that 2-3 bars static presure is not for r 507 :P


2-3 bar isn`t enough even for propane :p

[hincó]

2-3 bar isn`t enough even for propane :p
I was wrong (like in song [; )
But i still learn a lot at forums :)

[hincó]

I play with it a little bit today ; ]
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz041.jpg
Two bad termometers :p::lol2:
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz042.jpg
SLHX is loosing its' ice [;
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz043.jpg

http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz044.jpg

http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz045.jpg
only two screws are holding top
http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz046.jpg

http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz047.jpg

http://i29.photobucket.com/albums/c272/hinco_1988/ss/Obraz048.jpg


A lot of work is waiting for me ; ]