Collective Q9450 and P5Q series thread issue thread

[Leeghoofd]

LATEST 1406 BIOS SOLVED ALL TILL KNOW ALL KNOWN ISSUES WITH Q9450 OR OTHER YORK CPU'S -- IF YOU STILL ENCOUNTER PROBS PLZ USE A PM MESSAGE -- NEW BIOSSES ARE ALREADY IN THE WORKS

K After reading numerous posts of users with this hardware combination, I think it will be more easier to find users with the same issue(s) if we have one collective thread on the matter... users with other 45nm quads also can pop in... This is easier for the Asus tech to dig in...


Plz fill in the following info and vote in the poll plz

P5Q ... (type) made in (Taiwain or China)
daily OC used :
Voltage settings used :

CPU Voltage:
CPU GTL Voltage Reference (0/2):
CPU GTL Voltage Reference (1/3):
CPU PLL Voltage:
FSB Termination Voltage:
DRAM Voltage:
NB Voltage:
NB GTL Reference:
SBridge Voltage:
PCIE SATA Voltage:

Load Line Calibration:
CPU Spread Spectrum:
PCIE Spread Spectrum:
CPU Clock Skew :
NB Clock Skew :
if bios later than 0803 : which setting for CPU enhancement... :

Operating System used :

RAID : (yes or no) in case of Yes type of RAID

Drivers from Cd : (yes or no) in case of no : plz fill in the version

Issue encountered : (brief description) if no issues plz state so...


counteracts taken : eg bios reflash, hardware swap, cmoss reset, format, other drivers, other OS,...



CURRENT STATS :

Influenced boards :
P5Q Dlx Total 4 out of 6 not solved : Taiwanese model seems to be influenced (4 issues till now)

CPU's :
Q9450 : 3 out of 6 : 3 issues solved with Performance EDIT : other 3 now with 1406 bios (user confirmed)

Q9550 : solved with performance setting
QX9650 : 1 out of 2 not solved : still multiplier issues

[SuporterPoli]

P5Q Deluxe China
daily OC used : 3800MHz
Voltage settings used :

CPU Voltage: 1.39375
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: 1.6
FSB Termination Voltage: 1.28
DRAM Voltage: 1.98
NB Voltage: 1.28
NB GTL Reference: Auto
SBridge Voltage: 1.2
PCIE SATA Voltage: 1.5?

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Default
NB Clock Skew : Default
if bios later than 0803 : which setting for CPU enhancement... :
now with 1306 the default setting
Operating System used :
Vista Ultimate x64 SP1
RAID : (yes or no) in case of Yes type of RAID
NO
Drivers from Cd : (yes or no) in case of no : plz fill in the version
YES
Issue encountered : (brief description) if no issues plz state so...

I upgraded to 1306 with the Asus utility(default clocks on everything) and then reapplied the settings from my old 0803 bios and everything works. Fixed a couple of major problems that i had with my 4870x2.
I am in a business trip right now so i am not able to reach my pc but as far as i remember these are my settings. I think the bios is 1306, its the last bios that the Asus software found for my board.

[LUCI5R]

I would also like to invite everyone using a Q9450 w/ P5Q Deluxe and having issues using any BIOS > 0803 (The 'CPU Margin Enhancement' setting as we've come to understand), to please come in this thread & make a post. As Leeg advised me, ASUS Techs will be looking into this thread to find out the amount of people having problems, and the nature of the problems.

P5Q made in : Taiwan
daily OC used : 3.8Ghz

Voltage settings used :

CPU Voltage: 1.35v
CPU GTL Voltage Reference (0/2): 0.65
CPU GTL Voltage Reference (1/3): 0.65
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.34
DRAM Voltage: 1.96
NB Voltage: 1.34
NB GTL Reference: 0.65
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.50

Load Line Calibration: ENABLED
CPU Spread Spectrum: DISABLED
PCIE Spread Spectrum: DISABLED
CPU Clock Skew : NORMAL
NB Clock Skew : NORMAL
if bios later than 0803 : which setting for CPU enhancement... : N/A

Operating System used : Vista Ultimate (32-Bit)

RAID : NO

Drivers from Cd : NO

Issue encountered :
Cannot boot into Vista using BIOS > 0803. Any BIOS > 0803 results in Freezes, BSOD's.
*NOTE: Only at BIOS 0803 the system boots in & works as normal. This issue started over a period of time - not immediately upon flashing to BIOS > 0803.

counteracts taken : eg bios reflash, hardware swap, cmoss reset, format, other drivers, other OS,...[/QUOTE]
Everything you can possibly think of. Formatted hard drive, re-installed Operating System, swapped hard drives, CMOS reset, bios flashed/re-flashed, all hardware removed & reconfigured.

Thanks.

[cadaveca]

Taiwan board.
BIOS 803


CPU Voltage: 1.125
CPU GTL Voltage Reference (0/2): .61
CPU GTL Voltage Reference (1/3): .61
CPU PLL Voltage: 1.5
FSB Termination Voltage: 1.2
DRAM Voltage: 2.2
NB Voltage: 1.2
NB GTL Reference: .67
SBridge Voltage: ???auto???
PCIE SATA Voltage: ???auto???

Load Line Calibration: disabled
CPU Spread Spectrum: disabled
PCIE Spread Spectrum: disabled
CPU Clock Skew : auto
NB Clock Skew : auto


Operating System used : Vista X64

RAID : RAID 0

Drivers from Cd : yes, plus newest INtel chipset INF9.0.0.xx

Issue encountered : Random hesitation, not able to reboot without clearing CMOS.


Board will boot better after flashing second bios(deluxe board) to 803(was 602, or something I cannot recall exactly), but will still not boot QX9650 C0 L739A cpu with multi higher than default. You can go into bios, change multi, boot once, then CMOS MSUT be cleared in order to boot again.

[Leeghoofd]

K thread is moving, but I see in total 6 votes but only 3 filled in the template... plz fill it in completely as just a vote is NOT enough !!

[sf rich]

Plz fill in the following info and vote in the poll plz

P5Q Deluxe, BIOS 1201, Intel Q9550 C1 stepping
daily OC used : None
Voltage settings used : All Stock

CPU Voltage:
CPU GTL Voltage Reference (0/2):
CPU GTL Voltage Reference (1/3):
CPU PLL Voltage:
FSB Termination Voltage:
DRAM Voltage:
NB Voltage:
NB GTL Reference:
SBridge Voltage:
PCIE SATA Voltage:

Load Line Calibration:
CPU Spread Spectrum:
PCIE Spread Spectrum:
CPU Clock Skew :
NB Clock Skew :
if bios later than 0803 : which setting for CPU enhancement... :

Operating System used : Windows XP SP 2

RAID : (yes or no) in case of Yes type of RAID: NO

Drivers from Cd : (yes or no) in case of no : plz fill in the version: no

Issue encountered : (brief description) if no issues plz state so...

No BSODs or software problems, but P95 failed after 3 - 5 minutes on at least 1 CPU. Ran P95 multiple times, always failed. Switched CPU Margin Enhancement from Optimized to Performance and P95 worked perfectly. [NOTE: Edited, got them reversed earlier. My mistake]

Haven't tried to OC yet, perhaps will get started this week-end.


counteracts taken : eg bios reflash, hardware swap, cmoss reset, format, other drivers, other OS,...

[mac_69]

P5Q ... P5Q Deluxe made in Taiwan
daily OC used : 3.6 Q9450
Voltage settings used : 1.34375

CPU Voltage:
CPU GTL Voltage Reference (0/2): 0.635
CPU GTL Voltage Reference (1/3): 0.675
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.34
DRAM Voltage: 2.02
NB Voltage: 1.3
NB GTL Reference: Auto
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.50

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto



Operating System used : Vista x64 SP1

RAID : No, dual drive but non raid

Drivers from Cd : Yes, but updated ALL drivers from Asus website to current releases

Issue encountered :

I am effectively unable to use any bios higher than 803, and now even with bios 803 the system does not power off from vista - it tries to reboot - this lack of power off started occuring recently. This occured without changing anything in either bios nor software which has me worried about cpu longevity.

Using higher bioses than 803 results in non stable overclock: I cannot run 3.6 stable in prime95 where with 803 and the same bios settings it will run for 8 hours each on small, large and blend tested one after each other.

Also, on bioses higher than 803, the cpu will not speedstep, its locked on 3.6 for the same bios settings.

I got scared enough from briefly using higher bioses (and reading other users problems) to revert to 803, and I was stable for a time but now I am worried as the system will not shutdown anymore from vista.

I was unable to reload vista on higher bioses (see below)


counteracts taken :

System would attempt bios recovery to "delivery bios". I have systematically tried everything suggested in these threads.

The process which works for me (in a recovery from lock up on higher than 803 bios) is to use the reset jumper, and then also remove the cmos battery for a time, then reflash to 803 then manually re-enter my settings from my template.

I had a hell of a time trying to reload vista on higher bioses. It would only work successfully on 803 and with IDE mode for the install. Both intel RAID and Drive expert Raid failed on me after a short time (I am not sure if the RAID/drive expert issue is directly related to this issue as I got fed up enough not to troubleshoot it properly, but I'm commenting on it anyway for information)

I have reformatted a few times after trying higher bioses, which I'm basically sick of doing this and crave a stable system. 803 was stable but the restart on shutdown error has just started.

My cpu processor serial number is:

SLAWR MALAY
2.66 GHZ/12M/1333/05A
L8038553

The rest of my hardware is in my signature below.

[SuporterPoli]

sf rich is your board also from Taiwan? Until now the common thing is that the boards with problems(3 so far) are from Taiwan.

[Leeghoofd]

Posting from german forum in name of eAndy

P5Q Deluxe made in Taiwan
S/N Product: 85M0AG101263
Voltage settings used : Auto

CPU Voltage: Auto
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: Auto
FSB Termination Voltage: Auto
DRAM Voltage: Auto
NB Voltage: Auto
NB GTL Reference: Auto
SBridge Voltage: Auto
PCIE SATA Voltage: Auto

Load Line Calibration: Auto
CPU Spread Spectrum: Auto
PCIE Spread Spectrum: Auto
CPU Clock Skew : Auto
NB Clock Skew : Auto
bios spater den 0803 : 1403
CPU enhancement... : performance mode

Operating System : Vista X64 Sp1

RAID : (ja oder nein) : Yes

Drivers from Cd : (ja oder nein ) : no

Issues encountered : Instabilities, BSODs, Programm Crashes


Counteracts taken : I set CPU Margin Enhancement on "Performance Mode"

[ssabripo]

P5Q Deluxe made in Taiwan
S/N Product:
Voltage settings used : Auto

CPU Voltage: Auto
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: Auto
FSB Termination Voltage: Auto
DRAM Voltage: Auto
NB Voltage: Auto
NB GTL Reference: Auto
SBridge Voltage: Auto
PCIE SATA Voltage: Auto

Load Line Calibration: Auto
CPU Spread Spectrum: Auto
PCIE Spread Spectrum: Auto
CPU Clock Skew : Auto
NB Clock Skew : Auto
bios : 1403
CPU enhancement... : performance mode

Operating System : Vista X64 Sp1, Vista x86 (32bit)

RAID : : No

Drivers from Cd : : no

Issues encountered : Cannot install Vista at all, either x64 or x86. It hangs up in the first graphical screen (with mouse, and blue/green vista background), and then reboots.

Counteracts taken :
My setup consists of:
e8400
Asus P5Q pro (with latest Bios)
4 x 1GB crucial ballistix PC2-6400
2 x 250 SATA WD2500AAKS

so far, here is what I've tried:

a) Removed 2 x 1 GB sticks (from DIMM2 and DIMM4 slots).
b) Forced Bios Timings to memory 4-4-4-12 (as oem says) and 2.0 Vdimm
c) tried a different install disk of Vista x64, and even 32-bit
versions
d) removed all drives except one, and tried each one, one by one.
e) replaced all Sata cables, disconnected USB and other non-essential perihperals.
f) Used different RAM: Corsair XMS2 PC2-6400

in all cases, the same issue: it would hang up and reboot after copying installation files (right when 1st graphical screen starts up).

to double check: I installed XP pro SP3, and it worked fine with XP

[Leeghoofd]

Postin in name of Christian8672 (German hardwareluxx forum)

P5Q DLX made in China
daily OC used : 3200Mhz (8 x 400 )

Voltage settings used :

CPU Voltage: 1.28
CPU GTL Voltage Reference (0/2):
CPU GTL Voltage Reference (1/3):
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.22
DRAM Voltage: 2.0
NB Voltage: 1.26
NB GTL Reference: auto
SBridge Voltage: auto
PCIE SATA Voltage: auto

Load Line Calibration: enabled
CPU Spread Spectrum: auto
PCIE Spread Spectrum: auto
CPU Clock Skew : auto
NB Clock Skew : auto
if bios later than 0803 : 1306 bios with CPU enhancement to PERFORMANCE

RAID : (yes or no) in case of Yes type of RAID : no

Drivers from Cd : (yes or no) in case of no : yes

Issue encountered : BSOD, bios freezes, cold boot issues

counteracts taken : Asus tech, Multi 8,...

[Pants-Of-Fire]

CPU: Intel Q9300
P5Q ... Deluxe made in China
daily OC used : None
Voltage settings used :Auto

CPU Voltage:Auto
CPU GTL Voltage Reference (0/2):Auto
CPU GTL Voltage Reference (1/3):Auto
CPU PLL Voltage:Auto
FSB Termination Voltage:Auto
DRAM Voltage:2.2 (as per Geil specs)
NB Voltage:Auto
NB GTL Reference:Auto
SBridge Voltage:Auto
PCIE SATA Voltage:Auto

Load Line Calibration:Auto
CPU Spread Spectrum:Auto
PCIE Spread Spectrum:Auto
CPU Clock Skew :Auto
NB Clock Skew :Auto

Operating System used : Windows XP 32

RAID : No

Drivers from Cd : No - latest drivers from Asus Website

Issue encountered : 803 is very stable, but runs memory at Compatability 06 (later versions run at Compatability 05, but setting this on BIOS 803 causes a hard lock and CMOS needs clearing).

A BIOS later than 803 is very unstable, and fails Prime95 and IntelBurnTest anywhere from a few seconds to a few minutes. Increasing NB voltage to 1.52 and DRAM voltage to 2.36 helps a lot, but the system is still unstable, and applications crash, exit, etc. Anything later than 803 is basically unusable, although I think the improved memory support runs my Geil RAM slightly faster.

[douirc]

1402 yeilded me 475*8, where 0803 maxed out at 450*8. I still can't get to 500FSB on my Q9450, but my board does 520FSB on my E7200. oh well, I'll take the extra 200MHz oc.

[SuporterPoli]

douirc imho your vcore is kinda dangerous for 3.8 only.Mine does 3.8 with 1.39375 in bios which in load is 1.38.

[Leeghoofd]

Think that's an old signature... 780i 1.4 in bios could be only 1.3 in reality...

More results plz

[Leeghoofd]

Early results indicate 1406 bios seems to resolve the non boot, shutdown issue with Q9450 series and the P5Q series...

Plz give it a go

[LUCI5R]

Early results indicate 1406 bios seems to resolve the non boot, shutdown issue with Q9450 series and the P5Q series...

Plz give it a go

I second Leeg's appeal. Please flash to 1406 as soon as possible.
Check out detailed post: http://www.xtremesystems.org/forums/...postcount=4245

[Big Lar]

1406 is running fine here with my Q9400. I was not having Some of the problems that others encountered tho. No boot problems or shutdowns tho, of which Prime95 would occasionally lock up my system with previous bios, that is gone.

Larry

[LUCI5R]

1406 is running fine here with my Q9400. I was not having Some of the problems that others encountered tho. No boot problems or shutdowns tho, of which Prime95 would occasionally lock up my system with previous bios, that is gone.

Larry

All results by different users seem to be indicating 1406 to be a better BIOS.

@ Leeg ... is it possible to add 1406 to the Poll above?

[kimohw]

does the P5Q-E suffer from the same problem or it is only related to the Deluxe ?

[Pants-Of-Fire]

1406 works for me where anything over 803 was very unstable and flaky.

[Leeghoofd]

15 bios series is already in the works, I'll edit the first post to use the latest 1406 if a yorkfield cpu is used, thx to all for the posts...and a big thank you to sir Pmp...

[douirc]

douirc imho your vcore is kinda dangerous for 3.8 only.Mine does 3.8 with 1.39375 in bios which in load is 1.38.

y, i agree, but i want more mhz so i have to put more voltage. i figure if/when it dies, i'll upgrade to a Q9650. by then hopefully people are selling used ones for $200 that do 4.2ghz under 1.35v.

[Ender17]

P5Q Dlx (type) made in ??? (how do I tell?) (Taiwain or China)
daily OC used : stock
Voltage settings used : vdimm 2.1, everything else stock

CPU Voltage:
CPU GTL Voltage Reference (0/2): stock
CPU GTL Voltage Reference (1/3): stock
CPU PLL Voltage: stock
FSB Termination Voltage: stock
DRAM Voltage: 2.1
NB Voltage: stock
NB GTL Reference: stock
SBridge Voltage: stock
PCIE SATA Voltage: stock

Load Line Calibration:
CPU Spread Spectrum: stock
PCIE Spread Spectrum: stock
CPU Clock Skew : stock
NB Clock Skew : stock
if bios later than 0803 : which setting for CPU enhancement... : optimized and performance

Operating System used : Vista Ultimate x64

RAID : No

Drivers from Cd : can't remember

Issue encountered : system will not shutdown, only restarts; random BSODs


counteracts taken : flashed BIOS to 1406, changed CPU enhancement to Peroformance from Optimized; reinstallation of OS, different GPUs

I'm tired of the glitchiness of this board. Can't even run stock settings? What a POS!! Is this a problem on the Maximus II? Or any other known boards?

[Leeghoofd]

Did you check your memory? also this board overvolts the Ram (mine with 0.08), do your rams need 2.2 volt to be stable ? Which rams are we talking about ? I would do a reflash and then pop the battery for an hour or so... test them one at a time... did you try a reinstall ? put the dimms in the other slots, etc...