[Team.AU] E8500=6128MHz, Biostar P45 + Corsair PC10000 DOMINATORS 4-4-4-4 DualChannel
I know i know another Biostar thread LOL
but what can you say when this board is that good
no mods on my board and FSB limit of 611MHz for 32M SuperPi runs on CAS4 but i did do some superpi tests at 5.8GHz-5.9GHz tonight
i didn't want to kill anything so i stopped the session as condensation was really starting to get a bit much for me.....i will give me my best to make it stable at 5.9GHz for some 8M and 32M runs...i know i can do it damn it lol
Test Configuration:
Biostar TPower P45 board
***1.88vcore, 2.68vdimm, 1.69vMCH, 1.47vFSB***
Intel Core2 Duo E8500 Q740A497
2GB DDR2 PC10000 Corsair DOMINATORS (645MHz 1:1 4-4-4-8 timings)
PCI GFX Card MX200
620W Corsair PSU
Stock heatsink on NB (LN2 cooled with small pours)
kingpin F1 Extreme Edition Solid copper CPU LN2 Pot
Big mamma 35L LN2 Dewar
160GB PATA
Windows XP Pro 32bit SP3
I was FSB limited here.........and condensation kicked in when i figured out how to run 1.92vcore and -140C lol
this CPU is a monster.......i need a board that can give me stable 631MHz FSB so that i can bench it at 6GHz rofl
Validation Link: http://valid.x86-secret.com/show_oc.php?id=384946
here is my settings template i usually use and then adapt it to whatever cooling i am using....so it would be slightly different for the above run if you know what i mean
Code:SETTINGS M/B : BIOSTAR TP I45 (BIOS:626) CPU : Core2 Duo E8500(Q740A497) best CPU i've EVER had :D [EDIT]...errrr maybe my Opteron 146 with 11x multi still takes the cake CPU cooling : TTBig Typhoon Chipset Cooling : stock with extra fan Mem : 2GB Kit of Crucial Ballistix 2GB DDR2 PC10000 Corsair Dominator "dead" kit for CAS4 << still works eeek even it tons of errors in memtest heheh VGA : PCI GFX Card HDD : Samsung 160gb ide OS : Windows XP SP3 USB wireless mouse and PS2 keyboard [BIOS SETUP] O.N.E Over-Clocking Navigator [Manual OverClock] Intel(R) SpeedStep(tm) : Disabled Ratio CMOS Setting : ×6 (change higher for benching subzero obviously) CPU Frequency Setting : 570(boot) Over Clock Retry Count : 2 FSB Compensation: Enabled FSB(Bsel) To NorthBridge Latch : 1333 DRAM Frequency : DDR2-1140 DDR2 Enhance Mode : Disabled DRAM Timing Configuration DDR2 RCOMP Configuration : 2 Static tREAD Value : AUTO Configure DRAM Timing by SPD : Enabled [EDIT] this will give you CAS5 clocks and PL10 past 600MHz FSB for PL9 past 600MHz FSB you need to manually set CAS4 timings Clock Gen Configuration PCIE Frequency Setting : 100 CPU Clock Skew Control : 200ps (G)MCH Clock Skew Control : 100ps CPU Clock Driving Control : Auto Voltage Configuration CPU Voltage : SET WHAT IS REQUIRED FOR STABILITY AT MHZ YOU ARE BENCHING ON DDR Voltage : +0.600v (use more depending on RAM) Chipset Voltage : +0.600v FSB Voltage : +0.40v CPU Core1 GTL Ref Voltage : 0.63*VTT CPU Core2 GTL Ref Voltage : 0.67*VTT MCH GTL Ref Voltage : Auto CPU PLL Voltage : 1.5v i also disabled Multicore Computing under CPU section for max Superpi with single core otherwise enabled for 3D benching
Originally Posted by dinos22
here is another update
32M SuperPi at 5826MHz....had a couple of runs stop at 584x and 585x so i gave up
also my hard drive must be screwed up as i am not happy with my efficiency but results are not too bad i guess
also here is a 6GHz 1M
absolutely hideous PP hehehehe
i am FSB limited by this board
this CPU has a lot more to give
with the right board...i would be expecting at least 5.9GHz 2D/3D
Josh is going to have a lot of fun with this CPU
it handles -150C plus no problems lol
update
8M SuperPi: 1m 41.9s
32M SuperPi: 8m 18.190s
Reply With Quote
), Juan J. Guerrero
Yes, Yellowbeard, a tall rough man with a big yellow beard
Bookmarks