DFI LANparty DK P45-T2RS/T3RS (Intel P45) - News|Info|Results

[Eldonko]

Just solder from that point to your trimpot to ground. If you look in vmod section you will see many examples.

[Turb0]

Sup everybody.
I have C2D e7300 (m0) with hunix original ram 2x1 (s5) and DK P45 (812bios).
My probles - is impossible to boot mainboard with followin settingson 410+ mhz:

CPU Feature
Thermal Management Control: Disabled
PPM(EIST) Mode: Disabled
Limit CPUID MaxVal: Disabled
CIE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled
Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
Shutdown after AC Loss: Disabled
CPU Clock Ratio: 6 X
Target CPU Clock: 2400Mhz
CPU Clock: 400
Boot Up Clock: 265
DRAM Speed: 333/666
Target DRAM Speed: 800Mhz
PCIE Clock: 100mhz
PCIE Slot Config: 1X 1X

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Voltage Settings
CPU VID Control: auto
DRAM Voltage Control: 2.2v
SB Core/CPU PLL Voltage: 1.75v
NB Core Voltage: 1.42v
CPU VTT Voltage: 1.35v
Clockgen Voltage Control: 3.75v
x CPU GTL1/3 REF : 61
x CPU GTL 0/2 REF : 61
x North Bridge GTL REF Volt: 58

DRAM Timing
Enhance Data transmitting: AUTO
Enhance Addressing: AUTO
T2 Dispatch: Disabled

Clock Setting Fine Delay is:
0-0-2 and tryed 3-3-1

Ch2 Clock Crossing Setting: AUTO

DRAM Timings:

CAS Latency Time (tCL): 5
RAS# to CAS# Delay (tRCD): 5
RAS# Precharge (tRP): 5
Precharge Delay (tRAS): 15
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance LVL (Read Delay) (tRD): 7

AUTO etc..
What a problem? I read much forums about dk p45, and every where MB was bootable with such setttings on 500+ mhz. %)
ps: sorry for my bad english (

[Aerou]

Have this fine mobo only shortly, but I cant go passed 583 MHz memory speed no matter what. It's like if it would hit a wall

CPU Clock Ratio: 6 X
CPU Clock: 580
DRAM Speed: 400/800 (tryed 333/667)
Target DRAM Speed: 1160

Voltage Settings
CPU VID Control: +200
DRAM Voltage Control: 2.338v (tryed 2.1 - 2.4V)
SB Core/CPU PLL Voltage: 1.55v
NB Core Voltage: 1.43v (tryed 1.4 - 1.5V)
CPU VTT Voltage: 1.38v
x CPU GTL1/3 REF : 63
x CPU GTL 0/2 REF : 62
x North Bridge GTL REF Volt: 58

(tryed all option of the settings below)
DRAM Timing
Enhance Data transmitting: normal
Enhance Addressing: normal
T2 Dispatch: Disabled

Clock Setting Fine Delay is:
3-3-1

Ch2 Clock Crossing Setting: more relaxed

DRAM Timings:

CAS Latency Time (tCL): 5
RAS# to CAS# Delay (tRCD): 5
RAS# Precharge (tRP): 5
rest auto
Performance LVL (Read Delay) (tRD): 10

Any ideas, tips or suggestion? Thing is, that the memory ( OCZ D9GMH SLi EPP kit) needs 2.12V to get to 583, but anything higher results in errors in memtest, no matter how much voltage.

Every thing is well aircooled, except the cpu, which is watercooled. Really strange, because till 580, it is primestable and at 583+ it isnt even SPI 1M stable

[bluto]

Tried everything and this booted for me and 1M stable .If you guys have any suggestions to fine tune pls. tell me cause not 32M stable yet .Thanks.

600mhz boot bios settings: E8600 on H2o (812 bios ver.)/cell shock pc2-9200
CPU vid control:+150mV
DRAM 2.408v
SB Core/CPU PLL voltage: 1.55v
NB Core : 1.4575
CPU VTT:1.35
DRAM timing : 5-5-5-18 , T2 disable,clock setting fine delay 3-3-1
clockgen volt. control: 3.60v
cpu gtl0/2 reg volt: .61x
cpu gtl1/3 ref volt: .61x
NB gtl ref volt: 58
NB Vref :2A
CPU clock ratio: 7x
CPU amplitude: 800mv -100ps-0ps
DRAM speed : 333/667
----Target DRAM speed :1200mhz
Boot UP Clock : AUTO

[Alex-Ro]

E8600,preparations,650 fsb 1m,2xfast,5-5-5-15,665 validation,could be done greater but limited time,see ya on Ln2 Mobo and chipset under air,Dfi Lanparty Dk P45 T2RS-Plus.

http://valid.x86-secret.com/show_oc.php?id=416266

[emoners]

@Alex-Ro: what's your settings on that run?

[Aerou]

more importantly, what memory?

[EmineM]

more specific bios settings woud be nice

[Alex-Ro]

OCZ platinum rev blablabla,ordinary D9GMH

[Diegis0n]

OCZ platinum rev blablabla,ordinary D9GMH

Other then GKX not much ordinary there

Nice run

[emoners]

by the way, which code/clock gen on SetFSB works on this board?

[Aerou]

OCZ platinum rev blablabla,ordinary D9GMH

cmon, stop teasing there are lots of guys like me with walls here, maybe you can help them breake them

by the way, which code/clock gen on SetFSB works on this board?

ICS9LPRS918JKL, and btw, you can find the chip on the mobo (below the first PCIe 16 slot, on the right of the first PCIe 1x one )

[emoners]

ICS9LPRS918JKL, and btw, you can find the chip on the mobo (below the first PCIe 16 slot, on the right of the first PCIe 1x one )

thanks man...i also checked SetFSB's site

[emoners]

anybody got a stable OC on this board with a Q6600?

[PolRoger]

I just got this board for my new small form factor build last week. It took some time but I finally made it to 600! I'm using OCZ Reaper PC2-9200 (the newer 2.1v revision).

[emoners]

@PolRoger: could you list your bios settings please. thanks

[cole2109]

[MacClipper]

TRUE120 aircooled with enough room to move up still, DFI FTW!

[Pcuser]

What is it with this board, same settings that worked yesterday dont work today
Can boot @600 x6/7 , also did 5.5G with 9.5 multi(E8500) but next day without changing any settings wont even boot @4.5

[PolRoger]

@PolRoger: could you list your bios settings please. thanks

There may be better (more refined) settings but here you go:

Enhance Data Transmitting: Auto
Enhance Addressing: Auto
T2 Dispatch: Disable
Clock Setting Fine Delay: 0-0-1
Ch1 Clock Crossing: Nominal
Ch2 Clock Crossing: Nominal
Flex Memory: Auto
5-5-5-15-5-42-10 the rest: Auto

CPU: +250 (probably doesn't need that much)
DRAM: 2.266
SB Core/CPU PLL: 1.55v
NB: 1.3825v
CPU VTT: 1.38v
Clock Gen: 3.60v
CPU GTL 0/2: 67x
CPU GTL 1/3: 67x
NorthBridge GTL: 58x
FSB Vref: 2A

600x7

Boot Up Clock: Auto
CPU Clock Amp: 800mv
CPU Clock0 Skew: 200ps
CPU Clock1 Skew: 0ps
DRAM Speed: 400/800
PCIE: 100

BIOS: 0812

Memory: OCZ Reaper PC2-9200 (2.1v Revision)

[Lestat]

guys the 0901 bios is out and it implements vcore droop stoppage
just flash the bios reboot and go under the voltage control screen.
DISABLE it to get Z E R O vcore droop!!!!!!!

[DiscoTech]

what is the difference betwen the regular one and the plus version?

how does this motherboard compare to the biostar i45?

which one would overclock a dual core better?

[emoners]

thanks PolRoger!

i'm still confused with these settings tho...

Clock Setting Fine Delay: 0-0-1
Ch1 Clock Crossing: Nominal
Ch2 Clock Crossing: Nominal
Flex Memory: Auto
FSB Vref: 2A
CPU Clock Amp: 800mv
CPU Clock0 Skew: 200ps
CPU Clock1 Skew: 0ps

[MacClipper]

Vdroop Control defaults to Enabled on my Jr and if I disable it in BIOS 0901, Prime95 quickly fails in one of the cores, ceteris paribus.

[PolRoger]

thanks PolRoger!

i'm still confused with these settings tho...

Clock Setting Fine Delay: 0-0-1
Ch1 Clock Crossing: Nominal
Ch2 Clock Crossing: Nominal
Flex Memory: Auto
FSB Vref: 2A
CPU Clock Amp: 800mv
CPU Clock0 Skew: 200ps
CPU Clock1 Skew: 0ps

What do you find confusing about them? These settings may not be suitable with your combination of cpu and memory. (Pressing F9 in the BIOS gives you the option of opening up the advanced memory timings menu. The proper configuration of Clock Setting Fine Delay will help allow high fsb)